TRENDnet TEG-S80TXD User manual

TEG-S80TXD

Version 10.18.2005

User’s Guide

Table of Contents

English ............................................................................................

Românǎ ..........................................................................................

1. Introduction .............................................................................

2. Unpacking and Setup ..............................................................

3. Identifying External Components ............................................

1. Introducere ..............................................................................

2. Despachetare si instalare .......................................................

3. Identificarea componentelor externe .......................................

Technical Specifications ..................................................................

This section describes the features of the 8-Port 10/100/1000Mbps Gigabit

Ethernet Switch.

Features

The 8-Port 10/100/1000Mbps Gigabit Ethernet Switch was designed for easy

installation and high performance in an environment where traffic on the

network and the number of users increase continuously.

1. Introduction

English UG

English

8 x 10/100/1000Mbps Auto-negotiation Gigabit Ethernet ports

Auto-MDIX for each port

Supports Full/Half duplex transfer mode for 10 and 100Mbps

Supports Full duplex transfer mode for 1000Mbps

Wire speed reception and transmission

Store-and-Forward switching method

Supports 8K entries absolute MAC address table

Supports 256K Bytes RAM for data buffering

Extensive front-panel diagnostic LEDs

IEEE 802.3x flow control for full-duplex

Back pressure flow control for half-duplex

Optional Rack-mount Kit for 19” standard rack

2English

2. Unpacking and Setup

This chapter provides unpacking and setup information for the Switch.

Unpacking

Open the shipping carton of the Switch and carefully unpack its contents. The

carton should contain the following items:

If any item is found missing or damaged, please contact your local reseller for

replacement.

TEG-S80TXD

User's Guide

Four rubber feet with

adhesive backing

AC power cord

TEG-S80TXD

Version 10.18.2005

User’s Guide

3English

Setup

Desktop Installation

The setup of the Switch can be performed using the following steps:

When installing the Switch on a desktop or shelf, the rubber feet included with

the device must be attached first. Attach these cushioning feet on the bottom at

each corner of the device. Allow enough ventilation space between the device

and the objects around it.

The surface must support at least 5 kg.

The power outlet should be within 1.82 meters (6 feet) of the device.

Visually inspect the power cord and see that it is secured fully to the AC

power connector.

Make sure that there is proper heat dissipation from and adequate

ventilation around the Switch. Do not place heavy objects on the Switch.

Gigabit Ethernet Switch installed on a Desktop or Shelf

Rack Installation (optional)

The 8-Port 10/100/1000Mbps Gigabit Ethernet Switch can be mounted in an

EIA standard size, 19-inch rack, which can be placed in a wiring closet with

other equipment. To install, attach the mounting brackets on the Switch's front

panel (one on each side) and secure them with the provided screws.

Then, use the screws provided with the equipment rack to mount the Switch in

the rack.

English

Installing the Switch on an equipment rack

Attaching the mounting brackets to the Switch

5English

Connecting Network Cable

AC Power

The 8-Port 10/100/1000Mbps Gigabit Ethernet Switch supports eight

10/100/1000Mbps Gigabit Ethernet ports. These ports support half or full

duplex mode when running in 10Mbps or 100Mbps. They support full duplex

while running in 1000Mbps.

These ports are Auto-MDIX type port. They can auto transform to MDI-II or

MDI-X medium type, so you can just make an connection with a straight or

crossover cable.

The 8-port Gigabit Ethernet Switch can be used with 100~240V AC, 50~60 Hz

power source. The power supply of the Switch will adjust to the local power

specification automatically and may be turned on without having any or all LAN

segment cables connected.

6English

3. Identifying External Components

The front panel of the Switch consists of eight 1000BASE-T ports and LED

indicators.

This chapter describes the front panel, rear panel and LED indicators of the

Switch

Front Panel

Front panel view of the Switch

Rear panel view of the Switch

Eight Gigabit Ethernet ports of 10/100/1000Mbps Auto-Negotiation

interface.

Comprehensive LED indicators display the conditions of the Switch and

status of the network. A description of these LED indicators follows (see

LED Indicators).

AC Power Connector: This is a three-pronged connector that supports

the power cord. Plug in the female connector of the provided power cord

into this connector, and the male into a power outlet. Supported input

voltages range from 100~240V AC at 50~60 Hz.

Rear Panel

The rear panel of the Switch consists of an AC power connector. The following

figure shows the rear panel of the Switch.

7English

The LED indicators of the Switch including Power, Link/Act, 1000Mbps and

100Mbps. The following shows the LED indicators for the Switch along with

explanation of each indicator.

The Switch LED indicators

LED Indicators

This indicator lights green when the Switch is receiving power. It is off for

no power.

This LED indicator lights green when there is a valid connection (or link) to

the port. The LED indicator blinks whenever there is reception or

transmission (i.e. ActivityAct) of data at a port.

This LED indicator lights green when there is a valid 1000Mbps Gigabit

Ethernet connection (or link) to the port.

This LED indicator lights green when there is a valid connection (or link) to

100Mbps Fast Ethernet device at the port.

Power:

Link/ACT:

1000Mbps:

100Mbps:

If the connection (or link) is 10Mbps, both 1000Mbps and 100Mbps LED

indicators are off.

1. Introducere

Românǎ

Aceasta sectiune descrie caracteristicile Switchului cu 8 porturi

10/100/1000Mbps Gigabit Ethernet

Trasaturi

Switchul cu 8 porturi 10/100/1000Mbps Gigabit Ethernet a fost realizat in

vederea unei instalari usoare si unei performante ridicate, intr-un mediu unde

traficul in retea si numarul utilizatorilor sunt intr-o continua.

8 porturi x 10/100/1000Mbps Auto-negociere Gigabit Ethernet

Auto-MDIX pentru fiecare port

Suporta mod de transfer Full/Half duplex pentru 10 si 100Mbps

Suporta mod de transfer Full duplex pentru 1000Mbps

Viteza la nivel de “fir” pentru receptare si transmitere

Metoda switching Store-and-Forward

Suporta intrari 8K table adrese absolute MAC

Supporta 256K Bytes RAM pentru buffering la informatie

LEDuri pentru diagnostic pe panpul frontal

Control al fluxului de tip IEEE 802.3x pentru full-duplex

Control al fluxului de presiune pentru half-duplex

Kit Rack optional pentru rack standard 19” .

Other manuals for TEG-S80TXD

Table of contents

Languages:

Other TRENDnet Switch manuals

TRENDnet

TRENDnet TE100-S50g User manual

TRENDnet

TRENDnet TK-408K User manual

TRENDnet

TRENDnet TE-910plus User manual

TRENDnet

TRENDnet TPE-S160 User manual

TRENDnet

TRENDnet TEG-S80Dg User manual

TRENDnet

TRENDnet TI-PG541i User manual

TRENDnet

TRENDnet TE100-S50g User manual

TRENDnet

TRENDnet TPE-TG44G User manual

TRENDnet

TRENDnet TK-CAT508 Quick start guide

TRENDnet

TRENDnet TPE-TG160g User manual

TRENDnet

TRENDnet TPE-224WS - Web Smart PoE Switch User manual

TRENDnet

TRENDnet TK-802R User manual

TRENDnet

TRENDnet TK-209K User manual

TRENDnet

TRENDnet TK-401R User manual

TRENDnet

TRENDnet TPE-TG80G User manual

TRENDnet

TRENDnet TI-PG80 User manual

TRENDnet

TRENDnet TE100-S24R User manual

TRENDnet

TRENDnet TK-1603R User manual

TRENDnet

TRENDnet TK-210K User manual

TRENDnet

TRENDnet TK-802R User manual

TRENDnet

TRENDnet TK-802R User manual

TRENDnet

TRENDnet TK-208K User manual

TRENDnet

TRENDnet TEG-S18TXE User manual

TRENDnet

TRENDnet TK-408K User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual