TRENDnet TEW-WLC100 User manual
Quick Installation Guide
TEW-WLC100 (V1)
Table of Content
1 English
1. Before You Start
2. Hardware Installation and Configuration
3. Connect your wireless access points
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
1
1. Before You Start
Package Contents
ŸTEW-WLC100
ŸQuick Installation Guide
ŸCD-ROM (User's Guide)
ŸPower adapter (12V DC, 1A)
ŸRack mount kit
Minimum Requirements
ŸComputer with an Ethernet port and web browser
ŸNetwork cable for computer connection to controller
ŸCompatible wireless access point(s) (TRENDnet TEW-755AP, TEW-821DAP, or TEW-825DAP)
Optional Equipment
ŸEIA standard 19” rack
ŸPower drill/drill bits and Phillips bit or screwdriver for mounting
Make sure your existing network is using a DHCP server to distribute IP addresses to the access
points. By default, TRENDnet access points listed below will obtain an IP address automatically
through DHCP or otherwise default back to 192.168.10.100 / 255.255.255.0 if a DHCP server is
not available on your network. Each access point must be assigned a unique IP address on the
same network. The wireless controller and access points must be connected to the same IP
subnet on your network (e.g. 192.168.10.x / 255.255.255.0).
Important Note:
2
Access Point Model Description Controller Compatible
Firmware Version
TEW-755AP N300 PoE Access Point 1.03 or above
TEW-821DAP AC1200 Dual Band PoE Access Point 1.05 or above
TEW-825DAP AC1750 Dual Band PoE Access Point 1.01 or above
Access Point Compatibility
Before you proceed, please ensure you are using one of the access point models in the list and
the firmware version of your access point has been upgraded accordingly to the versions
indicated in the list below. You can download the access point firmware from
http://www.trendnet.com/support which include instructions on how to upgrade the firmware.
Before any access points are added to the wireless controller, make sure to reset the access
points to factory default.
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
3
2. Initial Controller Setup
Note: Before connecting the wireless controller to the network and connecting other devices
such as PoE injectors or access points, follow the steps to set up your controller IP address
settings and administrator password first.
3. Assign a Static IP address to your computer's network adapter in the subnet of 192.168.10.x
(e.g. 192.168.10.25) and a subnet mask of 255.255.255.0.
4. Open your web browser, type the default IP address of the wireless controller in the address
bar, and then press Enter. The default IP address is 192.168.10.200.
1
Power
2
4
6. Click Management and click on LAN.
5. Enter the User name and Password, and then click Login. By default:
User Name: admin
Password: admin
LAN
Management
Login
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
5
8. To change the controller administrator password, click Account Settings and click Edit.
Edit
Account Settings
7. Configure the wireless controller IP address settings to match the requirements of your
network and click Apply.
IP Address
Netmask
Gateway
DNS1
DNS2
192.168.10.200
255.255.255.0
192.168.10.1
192.168.10.1
6
10. Using an Ethernet cable, connect one of the five Gigabit Ethernet ports located on the back of
the wireless controller to your network (e.g. router, switch, etc.)
9. In the New Password and Confirm Password fields, enter the new administrator password
and click OK to save the new password settings. You will be prompted immediately
afterwards to login to the controller management page with the new password.
OK
Confirm Password
New Password
Network
TEW-WLC100
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
7
3. Connect your wireless access points
Important Note: Please make sure your access points have met the requirements in Section 1.
1. Using an Ethernet cable, connect each wireless access point to the wireless controller or your
network.
Note: If powering the access points using their power adapters, you can connect the access
points directly to your network or the wireless controller. If powering the access point using
power over Ethernet (PoE), you can connect your access points to your network or to the
wireless controller using a separate PoE injector (not included) or PoE/PoE+ switch (not
included).
OR OR
Access Point
Power
Network
PoE Injector
Access Point
Network
PoE Switch
Access Point
Network
8
4. Initial Wireless Setup
1. Using your computer and web browser, access the wireless controller management page
using the newly assigned IP address settings (configured in Section 2) and login.
Note: If the IP address settings were not changed in Section 2, the IP address settings for the
controller are 192.168.10.200 / 255.255.255.0.
2. Click Monitor and click Devices.
3. The access points will be discovered automatically and appear in the Device List.
Note: If the access points do not appear, make sure the access points are powered by checking
the physical LEDs and physical cable connections and refresh the page.
Login
Devices
Monitor
Other manuals for TEW-WLC100
3
Table of contents
Other TRENDnet Network Router manuals
TRENDnet
TRENDnet TW100-BRV214 User manual
TRENDnet
TRENDnet TE100-S5Pplus Quick start guide
TRENDnet
TRENDnet TE100-S50g User manual
TRENDnet
TRENDnet TE100-S800i User manual
TRENDnet
TRENDnet TEW-452BRP - 108Mbps Wireless Super G Broadband... User manual
TRENDnet
TRENDnet TEW-752DRU User manual
TRENDnet
TRENDnet TW100-BRV304 - Advanced VPN Firewall Router User manual
TRENDnet
TRENDnet TE100-S88 User manual
TRENDnet
TRENDnet TVP-224HR User guide
TRENDnet
TRENDnet TDM-C504 User manual
TRENDnet
TRENDnet TW100-BRF114 User manual
TRENDnet
TRENDnet TW100-BRM504 User manual
TRENDnet
TRENDnet TEW-633GR - Wireless Router Installation and operation manual
TRENDnet
TRENDnet DSLR-2000G User manual
TRENDnet
TRENDnet TW100-BRF104 User manual
TRENDnet
TRENDnet TW100-BRF114 Instruction Manual
TRENDnet
TRENDnet TEW711BRV2 User manual
TRENDnet
TRENDnet TE100S8P - Fast Ethernet Switch User manual
TRENDnet
TRENDnet AC3200 User manual
TRENDnet
TRENDnet TW100-BRV304 SHEETS User manual
