Trader BEAR BESMOKEYV2 User manual

BESMOKEYV2 - User Manual

Smoke Alarm, Photoelectric, Surface Mount

220-240V AC, 9V Battery Back Up / Individual or Interconnected

Thank you for purchasing our smoke alarm. This instruction contains important

information on the correct installation and operation of your smoke alarm.

Read this instruction fully before attempting installation and retain them

for future reference.

Standard: AS 3786-2014

Licence Number: SMK41282

WARNING:

• This product must only be installed and serviced by appropriately qualied electrician;

• This product must only be used for the purpose described in these instructions and must be installed in

accordance with the wiring rules and regulations in local location.

• Hazardous voltage may be presented at the wire leads of this product.

• Disconnect the AC power before installing or removing the smoke alarm.

• Ensure that the product has been correctly installed and tested for safe operation before reconnecting the

electrical supply.

• DO NOT connect the interconnection wire to Live or Neutral.

• A non-pure sinusoidal power sources is not suitable for this smoke alarm (e.g. derived from square-wave

invertors).

• The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such as

vases, shall be placed on the apparatus.

Failure to follow these instructions may result in death or serious injury.

Specications:

Main Power Source 220-240V AC 50 Hz

Secondary Power Source

Suitable batteries: GP DC 9V carbon battery or PAKKO DC 9V

carbon battery; or EVE DC 9V Lithium battery; or Raymax DC

9V Alkaline battery

AC Operating Current <60mA

Interconnecting Max. 24 alarms (wired 150m maximum)

Operating Temperature 0 °C to 40 °C

Ambient Humidity 5-95%

Alarm Sensitivity 0.100-0.180 dB/m

Alarm Volume ≥ 85dB(A) @ 3m

Sound Pattern

ISO8201(BI 0.5s - pause 0.5s - BI 0.5s - pause 0.5s - BI 0.5s

- pause 1.5s, with the RED LED ashing, repeat this alarm

pattern)

Comply with AS 3786:2014+A 1 :2015+A2:2018

Product function description:

Function Indication Description

Standby status The Red LED ashes about every 48

seconds. The unit is working.

AC power indication The Green LED illuminates continuously. The unit is receiving AC power.

Low battery warning The unit chirps with Red LED ashing

about every 48 seconds.

The battery voltage is too low, must replace a new battery

within 30 days.

Fault warning The unit beeps twice and ashes twice

every 48 seconds

The unit is faulty, get helps from the section:“Trouble

Shooting”.

Self-test fault warning The Red LED ashes twice about every

48 seconds. The buzzer fault or buzzer detection circuit fault.

End-of-life warning The unit chirps between the Red LED two

times ashing.

The unit will send end-of-life warning after working 10

years. Need to replace a new smoke alarm.

Test function

The Red LED ashes once every second

with alarm sounding until the TEST

button is released.

• Test by pressing the TEST button on the smoke alarm

at least 5 seconds.

• The alarm will sound if all electronic circuitry, horn

and battery are working properly.

• If no alarm sounds, refer to“Trouble Shooting”.

• Recommend testing the alarm Weekly by pressing

the TEST button.

Silence function The Red LED ashes every 8 seconds.

• This smoke alarm has a built-in Silence feature.

• If cooking or other non-hazardous sources cause the

alarm to sound, it can be temporarily silenced by

pressing the HUSH button for above 2 seconds.

• The alarm enters silence mode for 10 minutes.

• After the 10 minute dormant period, the smoke

alarm will resume normal ooeration.

Fire alarm The Red LED ashes every second, with

alarm sounds. Generate alarm sounds when re happening.

Fire alarm memory The Red LED ashes twice every 24

seconds.

After the unit exits Fire alarm state, it enters the Fire alarm

memory state, and the red LED ashes twice every 24

seconds for 72 hours.

Interconnection alarm The unit generates alarm sounds without

Red LED ashing.

The unit will enter the interconnection alarm mode when

received wire interconnection alarm signals.

Interconnection alarm

memory The Red LED ashes once every 1 second.

After the unit exits Interconnection alarm state, it enters

Interconnection alarm memory state, and the red LED

ashes once every 1 second for 3 minutes.

Do not disturb The Red LED ashes about every 48

seconds.

The unit will stop nuisance warning about 10 hours

under low battery or fault mode when the HUSH button

is pressed.

CAUTION:

• Before using the silence function, identify the source of the smoke and make sure a safe condition existing.

After 10 minutes silence, the unit will resume to normal operation.

• DO NOT use an open ame to test your alarm which may damage the alarm or ignite combustible materials

and result in a re.

• If the alarm sounds, and it is not being tested, it means the unit detected smoke. THE SOUND OF THE ALARM

REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION.

Installation planning

• Recommended location of smoke alarms

• Standard guidelines should be followed and locations should be planned for optimum performance when installing

the smoke alarms. The Building Code or Australia and regional Government Legislations provide direction.

• For optimal performance, alarms should be mounted as close to the centre of the rooms as practical and on the ceiling

for residential applications (see diagram 2).

• Smoke alarms should be located in the vicinity of sleeping areas, bed rooms and along the path to the exit as the

sleeping quarters are usually further from building exits.

• Smoke alarms should be mounted near each end of hallways longer than 9 metres.

• Smoke alarms on ceiling must be installed at least 300mm away from walls or corners (see diagram 3).

• Where it is necessary to mount smoke alarms on a wall, use the inside wall of the room and position them between

300mm and 500mm from the ceiling. (See diagram 3).

• The alarm should be at least 500mm away from the apex of any angled ceiling surface and no greater than 1500mm

(see diagram 3).

• Alarms should be located in every room where electrical appliances are used.

Multi Storey

• Alarms should be installed on every oor level.

• Stairwells can act like chimneys as smoke can rise through them, so additional alarms should be located in these areas

(see diagram 1).

Mobile Homes

• For modern mobile homes or caravans with ecient insulation, install smoke alarms as recommended, refer

‘Recommended location of smoke alarms’.

• For older and mobile homes and caravans that are not well insulated on external surfaces compared to current

standards, external temperatures can vary to extreme heat or cold. In these cases the smoke alarm should be

mounted on an inside partition between 300mm and 500mm from the ceiling surface. This is to overcome the

problem where the temperature conditions on external surfaces may create a thermal barrier where smoke may not

reach the ceiling.

• If unsure of the insulation in the mobile home it is recommended to install the alarm on an inside wall panel, and for

minimum protection install at least one alarm near bedrooms.

• Note: for smoke alarm use in mobile homes it is recommended to test them before each excursion and at least once

a week during use, particularly if travelling on rough roads.

Locations to avoid:

• Air-conditioner ducts or appliance outlets that create airow such as heaters where combustion heat particles rise

and spread horizontally.

• Avoid locating the smoke alarms within 1 metre as it can cause nuisance triggering or smoke particles may be blown

away from alarm.

• Avoid installation in kitchen areas as nuisance triggering can occur from cooking fumes, heat or smoke particles

rising.

• Avoid installation in damp areas or extremely humid locations where relative humidity may reach 90%.

• Avoid installing in areas where there are large temperature variations such as 5 to 45 degrees as performance may

vary in extreme conditions and battery life may be reduced.

• Avoid installing alarms in areas that are considered“dead air space”where smoke will unlikely reach the alarm (see

diagram 3).

• It is recommended not to locate your alarm in the garage - products of combustion that are present when you start

your vehicle may cause nuisance triggering.

• Do not locate your alarm less than 500mm from the peak of an“A” frame type ceiling (see diagram 3).

• Avoid dusty areas or areas where insects may infest the unit as it may cause nuisance triggering or premature failure.

• Avoid installation in close proximity to other electrical equipment or uorescent lights as electromagnetic

interference may cause nuisance triggering.

CAUTION:

• All interconnected smoke alarms must be supplied from the same circuit.

• A common Neutral wire must be used for Interconnect to function.

• MAX. Interconnected alarms: 24.

• MAX. Wiring length between rst and last alarm: 150m.

• DO NOT connect the interconnect wires to Live or Neutral.

• Observe and follow all local and national electrical and building codes for installation.

• Use a minimum of 1.5 mm 250V insulated wire for all wiring, including interconnecting wiring.

Bedroom

Bedroom Bedroom

Living Room

Lounge Room

Kitchen / Dining

Diagram 1 Diagram 2 - Suggest alarm location

Diagram 3

Wiring Instructions:

Replace Battery Instructions:

Note: After replacing battery press the TEST button to ensure it is connected and working correctly.

Mounting Instructions:

1. Turn of the AC power .

2. Select the proper location for your smoke alarm.

3. Press the base on the instaltion position, mark installation holes of the bracket with pencil.

4. Bore tow installation holes on the sign with electric drill. Make diameter of holes 5mm. Strike the two plastic plugs into

holes with hammer (See diagram A).

5. Wired Live, Neutral and Interconnection wire according to wiring instruction.

6. Attach the base to the plastic plugs and x tightly the screws into the plastic plugs. (See diagram 8).

7. Take out battery and remove outside lm from battery, then insert the fresh battery into battery box. (See diagram C).

8. Close the alarm body. (See diagram D).

WARNING: To prevent injury, this unit must be securely attached to ceiling in accordance with the

installation instructions.

4V230511

What to do if the Alarm sounds

1. Alert any small children and elderly persons.

2. Leave immediately by your plan of escape. Every second counts, so don’t waste time getting dressed or picking up

valuables.

3. In leaving, don’t open any inside door without rst feeling its surface. If hot, or if you see smoke seeping through cracks,

don’t open that door! Instead, use your alternate exit. If inside door is cool, place your shoulder against it, open it slightly

and be ready to slam it shut if heat and smoke rush in.

4. Stay close to the oor if air is smoky. Breathe shallowly through a wet cloth if possible.

5. Once outside, go to your selected meeting place and make sure everyone is there.

6. Call the Fire Brigade on 000.

7. Don’t return to your home until ocials say that it is safe to do so. For further information on re safety contact your

local Fire Brigade.

Trouble Shooting:

Problem Cause and Remedy

The green LED does not light when AC power

supplied

• Check the AC line is properly connected to the smoke alarm.

• Ensure that the AC power is turned on.

The Red LED does not ash every 48s • Ensure that the battery and the AC power are properly connected.

Smoke alarm does not sound when tested

• Ensure that the battery and the AC power are properly connected.

• Clean the smoke alarm. Then take out the battery and turn o the AC

power. Install battery and turn on the AC power after 3 minutes.

Low battery warning • Ensure that the battery is properly connected.

• Replace at battery, refer to“Replace Battery” section.

Fault warning • Clean smoke alarm. Take out the battery and turn o the AC power.

Wait 3 minutes, then install battery and turn on the AC power.

Self test fault warning (reserved) • Press the“TEST/HUSH”button at least 15s, then release.

False alarm

• Press the“TEST/HUSH”button to silence it.

• Clean smoke alarm device.

• Move the smoke alarm device to new location.

The alarm sounds dierent from it is used to

• Ensure that the battery is not low voltage.

• Clean smoke alarm. Take out the battery and turn o the AC power.

Wait 3 minutes, then install battery and turn on the AC power. .

The alarm can’t interconnect

• Check the Live, Neutral, Interconnection wires are properly

connected

• Check the interconnected smoke alarms are supplied from the same

circuit.

If the problem still exists, please return to your electrical wholesaler.

If the unit is out of warranty, please replace another new alarm.

10 Year Manufacturer’s Warranty

This product has been manufactured to the highest quality standards.

This product is warranted to the original purchaser and is not transferable.

The product is guaranteed to be free from defects in workmanship and parts for a period of 10 Years from the date

of purchase. Defects that occur within this warranty period, under normal use and care will be repaired, replaced or

refunded. The benets conferred by this warranty are in addition to all other rights and remedies of the consumer under

Commonwealth, State and Territory laws in relation to the goods or services to which this warranty relates and Australian

Consumer Law. Risk in regard to the product to be repaired shall at all times remain with the Purchaser. The warranty

is given on the condition that the product to which it applies is used for the purpose and in the manner intended by

its construction and for no other purposes whatsoever. GSM Electrical (Australia) Pty Ltd shall not be responsible for

damage of any kind, caused by accidents, power surges, electrical storm damage, incorrect power current, infestation

(vermin or insect), incorrect installation, incorrect electricity or plumbing installation, improper use of controls or failure

to use the product in accordance with the operating instructions, general misuse or abuse or from normal wear and tear.

Any attempt by an unauthorised person to repair or tamper with the equipment shall render the warranty

null and void.

GSM Electrical (Australia) Pty Ltd’s liability under this warranty is limited to the replacement and/or repair of the defective

parts within the warranty period and does not extend to installation or removal of the product. Acceptance of liability by

GSM Electrical (Australia) Pty Ltd contained herein is to the exclusion of any other remedy whatsoever and howsoever

arising in respect of any equipment to which it applies.

Disposal:

Waste electrical products and batteries should not be disposed of with your other household waste.

The alarm is ideally suited for disposal within the waste electronic and electrical equipment (WEEE)

recycling scheme.

Please recycle where facilities exist. Check with your local authority, retailer or contact our Technical

Support team for recycling/disposal advice as regional variations apply.

Once the batteries are removed, the low battery warning chirp will stop. The batteries should always be

removed before disposal.

GSM Electrical (Australia) Pty Ltd

Level 2 142-144 Fullarton Road

Rose Park SA 5067

www.gsme.com.au

Phone: 1300 301 838

Fax: 1300 301 778

Warranty

Other Trader Security System manuals

Trader

Trader BEAR BESMOKEY10WM User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual