Toro 07297 User manual

This manual suits for next models

1

Popular Utility Vehicle manuals by other brands

Polaris

Polaris ACE 900 SP owner's manual

TrailMax

TrailMax T-12-UR manual

Floe

Floe Cargo Max 9.5-73 Assembly instructions

Taylor-Dunn

Taylor-Dunn B0-050-00 Operation, t roubleshooting and replacement parts manual

Taylor-Dunn

Taylor-Dunn ET 3000 manual

Kayo

Kayo S70 Assembly manual

Range Road

Range Road RR608 Assembly manual

Landoll

Landoll 900D Series Operator's manual

pronovost

pronovost PUMA-10000 Operator's manual

SSI SCHAEFER

SSI SCHAEFER WEASEL LITE user manual

Club Car

Club Car TURF 272 2005 Maintenance service manual

Cushman

Cushman Turf Truckster 84069 Parts & maintenance manual

BERG

BERG Large Trailer user manual

Cub Cadet

Cub Cadet Big Country 641 Operator's manual

Westward

Westward Go-4 XTR Operator's manual

Club Car

Club Car Carryall I 1999 owner's manual

Etnyre

Etnyre Street Flusher operation, maintenance, parts and safety manual

Landoll

Landoll 340 Operator's manual

1

All Rights Reserved

Printed in the USA

2001 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Canopy Kit

Workman1100/2100 and TwisterUtility Vehicle

Model No. 07297

Model No. 07297R

Form No. 3326-769 Rev B

Installation Instructions

Safety and Instruction Decals

Safety decals and instructions are easily

visible to the operator and are located near

any area of potential danger. Replace any

decal that is damaged or lost.

104-6731

Assembly

1. Position the machine on a level surface. Set the parking

brake, turn the ignition off, and remove the key.

If you leave the key in the ignition switch, someone

could accidently start the engine and seriously

injure you or other bystanders.

Remove the key from the ignition switch before

you do any maintenance.

Caution

2. If your vehicle has a Roll Over Protection System

(ROPS), proceed to step 3. If your vehicle does not

have a ROPS, proceed as follows:

A. Loosely attach the support brackets to the rear

support tube with 8 screws, 4 (5/16 x 2-3/4 in.) and

4 (5/16 x 1-3/4 in.); 16 flat washers (5/16 in.); and 8

flange nuts (5/16 in.) (Fig. 1).

B. Loosely attach the support brackets to the vehicle

with 8 screws (5/16 x 1 in.), 16 flat washers

(5/16 in.), and 8 flange nuts (5/16 in.) (Fig. 1).

3. Remove the rear bolt that holds the front fender to the

dash and front frame support on each side of the

vehicle. Do not remove the fenders from the vehicle

(Fig. 1).

1

23

4

5

6

7

8

9

Figure 1

1. Rear support tube

2. Left-hand support bracket

3. Screw, 5/16 x 2-3/4 in.,

and washer, 5/16 in.

4. Screw, 5/16 x 1-3/4 in.,

and washer, 5/16 in.

5. Flange nut and washer,

5/16 in.

6. Screw, 5/16 x 1 in,. and

washer, 5/16 in.

7. Left-hand front fender

8. Right-hand front support

9. Left-hand front support

2

4. Slide the slotted bracket on the front support between

the fender and vehicle. Loosely attach the front supports

to the floor of the vehicle using the existing hardware

on the vehicle (Fig. 1).

5. Secure the fenders with the bolts removed in step 3.

6. Loosely attach the canopy to the front supports using 4

long screws (5/16 x 2-3/4 in.), 8 flat washers (5/16 in.),

and 4 flange nuts (5/16 in.) (Fig. 2).

Note: The canopy support is already loosely attached to the

canopy (Fig. 2).

6

1

2

3

4

5

5

Figure 2

1. Canopy

2. Right-hand front support

3. Left-hand front support

4. Screw, 5/16 x 2-3/4 in.,

and washer, 5/16 in.

5. Flange nut and washer,

5/16 in.

6. Canopy support

7. If your vehicle has a ROPS, insert the clinch nuts into

the holes in the ROPS (Fig. 3). Lift the canopy and

attach it to the ROPS with 2 screws (3/8 x 1 in.) and 2

flat washers (3/8 in.) (Fig. 3). If your vehicle does not

have a ROPS, lift the canopy assembly and attach it to

the rear support tube with 2 screws (5/16 x 2 in.), 4

washers (5/16 in.), and 2 flange nuts (5/16 in.) (Fig. 4).

1

3

4

2

Figure 3

Vehicle with ROPS

1. ROPS

2. Clinch nut

3. Canopy

4. Screw, 3/8 x 1 in., and

washer 3/8 in.

1

23

4

Figure 4

Vehicle without ROPS

1. Rear support tube

2. Canopy

3. Screw, 5/16 x 2 in., and

washer, 5/16 in.

4. Flange nut and washer,

5/16 in.

8. Starting at the bottom of the vehicle and working your

way to the top, tighten all of the fasteners.

9. Adjust the front suspension; refer to Adjusting the Front

Suspension in the vehicle Operator’s Manual.