Toro 07352 User manual

TORO DELUXE HARD CAB DOORS

This cab is manufactured for TORO

by Jodale Perry Corporation.

These door kits are intended to

be used on the following cab :

TORO WORKMAN®

MD Series cab

07328

Installation Instructions

Model’s 07352 & 07353

3362-138 Rev A

1. Safety instructions/Specifications..…………………………….2

2. Installation instructions…………….……………………………3

3. Warranty statement……………………………………………..5

Sliding Window Door

Kit Model 07352

Solid Window Door

Kit Model 07353

Table of contents

Safety Instructions

• Read and understand the contents of this material

before operating the vehicle. Become thoroughly

familiar with the controls, capabilities and proper

use of the equipment.

• Door kits fit all Workman®MD series cabs

• DO NOT weld, cut, drill, or modify door structure in

any way.

• Always use safety belts.

2

3362-138

Before Operating

Specifications

• Safety Glass with door seal mounted on a square

tube construction with key lock handles and air

shock opening and closing dampeners.

• Adjustable striker plates and striker pin for door

handle latch.

• Mounts to cab on quick attach hinges.

• 07352 Door kit has a drivers side sliding access

window.

• Weight of each door kit adds 84 pounds to vehicle

GVW and reduces rated capacity by the same

amount.

InstallationInstructions

1. Install brass washers on all 4 door

pins. See Figure 1.

Install brass washers

on door pins

3

Figure 1

Figure 2

Figure 3

3362-138

2. Install ball studs into tabs

provided in cab frame. Figure 2.

Door ball stud

3. Install doors on cab by

door pins with the hinge

part of the door. Figure 3.

Door hinges

Installation Instructions

4.

Figure 4.

Figure 5.

4. Install the door air shock onto ball

stud in door as shown in Figure 4.

Then install other end of air shock

on to cab ball stud. NOTE: Do not

over stress glass by trying to install

air shock on to cab as glass may

shatter. You may need to loosen

door stop mounting bolts to allow

door to open wider. See Figure 5.

Air shock

Door stop

Safety clips

5. After installing air shocks, install

safety clips on both sides of the

ball stud receivers, See Figure 4,

to ensure that the air shocks do

not fall off.

Figure 6.

6. Loosen striker pin on cab and

gently close the door and see

where the striker pin should be

located to keep the door closed

tight. Figure 6. Once located

in it’s proper location, tighten

all hardware and then repeat

steps 1 thru 6 for opposite

side door. Striker pin

Door stop

Mounting bolts

8.

This manual suits for next models

1

Table of contents

Popular Utility Vehicle manuals by other brands

Polaris

Polaris ACE 900 SP owner's manual

TrailMax

TrailMax T-12-UR manual

Floe

Floe Cargo Max 9.5-73 Assembly instructions

Taylor-Dunn

Taylor-Dunn B0-050-00 Operation, t roubleshooting and replacement parts manual

Taylor-Dunn

Taylor-Dunn ET 3000 manual

Kayo

Kayo S70 Assembly manual

Range Road

Range Road RR608 Assembly manual

Landoll

Landoll 900D Series Operator's manual

pronovost

pronovost PUMA-10000 Operator's manual

SSI SCHAEFER

SSI SCHAEFER WEASEL LITE user manual

Club Car

Club Car TURF 272 2005 Maintenance service manual

Cushman

Cushman Turf Truckster 84069 Parts & maintenance manual

BERG

BERG Large Trailer user manual

Cub Cadet

Cub Cadet Big Country 641 Operator's manual

Westward

Westward Go-4 XTR Operator's manual

Club Car

Club Car Carryall I 1999 owner's manual

Etnyre

Etnyre Street Flusher operation, maintenance, parts and safety manual

Landoll

Landoll 340 Operator's manual