Texas Instruments TPS65720EVM User manual
User's Guide
SLVU324–March 2010
TPS65720EVM
The TPS65720EVM-515 evaluation module is a fully assembled and tested circuit for evaluating the
TPS65720 two-channel power management integrated circuit..
Contents
1 Introduction .................................................................................................................. 2
1.1 Requirements ....................................................................................................... 2
1.2 1.2 Applications .................................................................................................... 2
1.3 Features ............................................................................................................. 2
2 TPS65720EVM Electrical Performance Specifications ................................................................ 3
3 TPS65720EVM Schematic ................................................................................................ 4
4 Connector and Test Point Descriptions .................................................................................. 5
4.1 Enable Jumpers/Switches ........................................................................................ 5
5 Setup ......................................................................................................................... 7
5.1 Software Setup ..................................................................................................... 7
5.2 Hardware Setup .................................................................................................... 7
5.3 Running the Software ............................................................................................. 7
6 TPS65720EVM Assembly Drawings and Layout ...................................................................... 13
7 Bill of Materials ............................................................................................................. 16
List of Figures
1 TPS65720EVM Schematic ................................................................................................ 4
2 Hardware Board Connection .............................................................................................. 7
3 Starting the Software ....................................................................................................... 8
4 Software Charger View..................................................................................................... 9
5 Software DCDC1/LDO1 View............................................................................................ 10
6 GPIO View.................................................................................................................. 11
7 INTERRUPTS VIEW...................................................................................................... 12
8 TPS65720EVM Component Placement (Viewed From Top)........................................................ 13
9 TPS65720EVM Top Copper (Viewed From Top) ..................................................................... 13
10 TPS65720EVM Bottom Copper (X-Ray View )........................................................................ 14
11 TPS65720EVM Internal 1 (X-Ray View From Top)................................................................... 14
12 TPS65720VM Internal 2 (X-Ray View From Top)..................................................................... 15
List of Tables
1 TPS65720EVM Electrical and Performance Specifications ........................................................... 3
2 HPA515B Bill of Materials................................................................................................ 16
1
SLVU324–March 2010 TPS65720EVM
Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated
Introduction
www.ti.com
1 Introduction
1.1 Requirements
In order to operate this evaluation module (EVM), the following components must be connected and
properly configured. All components and connectors are supplied in the EVM except for the host computer
and the DC power supply. Software must be downloaded from the TI Web site at www.ti.com.
1.1.1 Software
To download the software that is necessary to operate the TPS65720EVM, check the TPS65720 product
folder on the TI Web site.
1.1.2 Host Computer
A personal computer (PC) with a USB port is required to operate this EVM. The TPS65720 software runs
on the PC and communicates with the EVM via the PC's USB port and the USB-to-GPIO interface.
PC Requirements :
• Windows™ 2000 or XP operating system
• USB port
• Minimum of 30 MB of free hard-disk space (100 MB recommended)
• Minimum of 256 MB of RAM
1.1.3 Power Supply Requirements
A DC power supply capable of delivering 5 V at 1 A is required to operate this EVM.
1.2 1.2 Applications
• Bluetooth Headsets
• Handheld Applications
1.3 Features
• Input voltage rating
• Output voltage adjustable via I2C Interface
• Battery charger with power path Management
• 300-mA charge current
• 200-mA step-down converter for TPS65720
• 2.25-MHz Switching Frequency
• 1 General-purpose 200-mA LDO
2TPS65720EVM SLVU324–March 2010
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
www.ti.com
TPS65720EVM Electrical Performance Specifications
2 TPS65720EVM Electrical Performance Specifications
Table 1. TPS65720EVM Electrical and Performance Specifications
Parameter Symbol Notes and Conditions Min Typ Max Unit
Input Characteristics
Input Voltage AC VAC 4.35 28 V
Input Voltage DCDC1 VIN_DCDC1 2.1 5.6 V
Input Voltage LDO1 VIN_LDO1 1.8 6.6 V
Bit <AC input current1, AC input current0> = 00 90 95 100
Input Current IAC,max mA
Bit <AC input current1, AC input current0> = 01 or 10 450 475 500
UVLO VUVLO VAC rising 3.2 3.3 3.45 V
UVLO Hysteresis VHYS-UVLO VAC falling 200 300 mV
Output Characteristics
Voltage Range at SYS VSYS 2.2 5.6 V
Output Voltage DCDC1 VDCDC1 VIN = Nom, IOUT = Nom 1.2 V
VIN = 2.3 V to 5.6 V, PFM operation, 1 3 %
0 mA to IOUT, max
Output Voltage Accuracy DCDC1 VIN = 2.3 V to 5.6 V, PWM operation, -2 2 %
0 mA to IOUT, max
Load Regulation PWM operation 0.5 %
Output Current DCDC1 IOUT,DCDC1 VIN = Min to Max 200 mA
Forward Current Limit High-side ILIMF VIN = 2.3 V to 5.6 V 425 600 775 mA
and Low-side MOSFET
Dropout Voltage LDO1 VIN,LDO = 2.05 V, IOUT = 200 mA 180 mA
Default Output Voltage LDO1 VLDO1 VIN = Nom, IOUT = Nom 1.85 V
Output Voltage Accuracy LDO1 -1.5 2.5 %
Output Current of LDO1 200 mA
Line Regulation LDO1 -1 1 %
Load Regulation LDO1 VIN = Nom, VOUT = VOUT2-5% -1 2 %
Systems Characteristics
Switching Frequency FSW 2030 2250 2480 kHz
Peak Efficiency hpk VIN =Nom 92 %
Full Load Efficiency hVIN = 3.6, VOUT = 2.05, IOUT = 400 mA 89 %
MIPSA25202R2
3
SLVU324–March 2010 TPS65720EVM
Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated
www.ti.com
Connector and Test Point Descriptions
4 Connector and Test Point Descriptions
4.1 Enable Jumpers/Switches
4.1.1 J1 – VIN
This header is the positive connection to the input power supply. The power supply must be connected
between J1 and J2 (GND). The leads to the input supply must be twisted and kept as short as possible.
The input voltage has to be between 4.35 V and 6 V.
4.1.2 J2 – GND
This header is the return connection to the input power supply. Connect the power supply between J2 and
J1 (VIN). The leads to the input supply must be twisted and kept as short as possible. The input voltage
has to be between 4.35 V and 6 V.
4.1.3 J3 – BAT / GND / TS
Connect your battery positive connection to pin 1 of J3, negative connection to pin 2 of J3. The battery
thermistor can be connected to pin 3 of J3. if an external thermistor is used, R2 must be removed.
4.1.4 J4 – SYS
This header is the positive output of the power path.
4.1.5 J5 – GND
This header is the negative output of the power path.
4.1.6 J6 – VIN_LDO1 / GND
This header is the input supply for the LDO1 on the EVM. VINLDO1 is directly connected to SYS with R4.
It also can be connected to VDCDC1 with R5. An external power supply can be connected between J6
pin1 (VINLDO) and pin2 (GND). Note that the resistors R4 and R5 must be removed when supplying the
LDO1 from an external power supply.
4.1.7 J7 – VDCDC1
This header is the positive output of VDCDC1 step-down converter. The output voltage of DCDC1 can be
adjusted to any voltage between 0.6 V and VINDCDC1 with the external voltage divider R7 and R8.
The default setting is 1.2 V. VDCDC1 is capable of sourcing up to 200 mA. A load can be connected
between J7 and J8 (GND).
4.1.8 J8 – GND
J8 is the return connection of VDCDC1 output rail. A load can be connected between J8 and J7
(VDCDC1).
4.1.9 J9 – VLDO
This header is the positive output of LDO1 linear regulator. The default output voltage of LDO1 is 1.85 V.
VLDO1 can be adjusted via I2C interface in the range between .
LDO1 is capable of sourcing up to 300 mA. A load can be connected between J9 and J10 (GND).
4.1.10 J10 – GND
J10 is the return connection of LDO1 output rail. A load can be connected between J10 and J9
(VDCDC1).
5
SLVU324–March 2010 TPS65720EVM
Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated
Connector and Test Point Descriptions
www.ti.com
4.1.11 J11 /INT / RESET / GND
J11 pin 1 is connected to the open-drain output /INT. J11 pin 2 is connected to the open-drain output
RESET. All open-drain outputs are pulled up with a resistor to the pullup voltage PULLUP. Pullup is
connected to VLDO1 with R10 on the EVM. Pullup also can be connected to VIN and VDCDC1 with the
resistors R20 and R21. J13 pin 3 is connected to GND.
4.1.12 J12 SYS/GPIO0/GPIO1/GPIO2/GPIO3/SYS
Four GPIOs are available on this header.
• J12 pin 1 is connected to the SYS voltage.
• J12 pin 2 is connected to GPIO0.
• J12 pin 3 is connected to GPIO1.
• J12 pin 4 is connected to GPIO2.
• J12 pin 5 is connected to GPIO3.
4.1.13 J13
J13 is the interface connector for the I2C interface. Connect a 10-pin ribbon cable between J13 and the
USB-to-GPIO interface.
4.1.14 JP1
JP1 connects the cathode of the LED D2 to GPIO2. If GPIO2 is configured as a current sink JP1 can be
removed to measure the current through the LED with an ammeter.
If GPIO2 is configured as an input or output, JP1 must be removed to disconnect the LED D2.
4.1.15 JP2
JP2 connects the cathode of the LED D1 to GPIO3. If GPIO3 is configured as a current sink, JP2 can be
removed to measure the current through the LED with an ammeter.
4.1.16 JP3 HOLD_DCDC1
Connect a shorting jumper between HOLD_DCDC1 and SYS to enable DCDC1. Note that if a power
supply is connected to AC, DCDC1 is enabled independent of the status of HOLD_DCDC1.
If the IC is supplied from BAT, DCDC1 is enabled when PB_IN is pulled low. To keep DCDC1 enabled,
HOLD_DCDC1 must be pulled high before /PB_IN is released high.
4.1.17 JP4 HOLD_LDO1
Connect a shorting jumper between HOLD_LDO1 and SYS to enable LDO1. Note that if a power supply is
connected to AC, LDO is enabled independent of the status of HOLD_LDO1.
If the IC is supplied from BAT, LDO is enabled when /PB_IN is pulled low. To keep LDO1 enabled,
HOLD_LDO11 must be pulled high before PB_IN is released high.
4.1.18 S1 – PB_IN
This is the pushbutton Input. Pressing S1 pulls PB_IN to GND and therefore enables DCDC1 and LDO1.
To keep DCDC1 / LDO1 enabled, the individual HOLD pins must be pulled high before PB_IN is released
high.
If a power supply is present at AC, both DCDC1 and LDO1 are enabled independent of the HOLD pins.
6TPS65720EVM SLVU324–March 2010
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
TPS65720EVM-515
Host Computer
USB to GPIO Interface
DC Power Supply
J1 J2
J13
J3
Lithium Ion
Battery
TS +
-
+-
www.ti.com
Setup
5 Setup
5.1 Software Setup
To download the software, go the TPS65720 product folder on the TI Web site (www.ti.com).
Download the software, and execute it to install the software.
5.2 Hardware Setup
Figure 2. Hardware Board Connection
5.3 Running the Software
Click on the TPS65720_1EVM icon to start the software. If no icon appears on the host computer, then
use the start button in the lower left corner of the screen to browse the program folders to find the
software. The default directory for software installation is Program Files\Texas
Instruments\TPS65720_1EVM.
Once the software is started, a dialog box appears (see Figure 3) and asks the user to select whether a
TPS65720 or TPS65721 is connected.
7
SLVU324–March 2010 TPS65720EVM
Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated
Setup
www.ti.com
Figure 3. Starting the Software
Once the used device is selected, the software starts up (see Figure 4).
By clicking on the Tabs CHARGER , DCDC1/LDO1, GPIO, and INTERRUPTS, the user can navigate
through the different Views
The window that first appears allows control of all charger settings and shows all the charger status Flags.
In the CHARGER Tab, users can enable/disable the charger and change charger parameters as regulated
output voltage on the Power Path (VSYS), Charge Voltage, Safety Timers, etc.
In the Lower right corner of the window, all charger related User Registers are displayed.
See the TPS65720 data sheet for detailed description on these registers.
8TPS65720EVM SLVU324–March 2010
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
www.ti.com
Setup
Figure 4. Software Charger View
The DCDC1/LDO1 control window (see Figure 5) allows control of operating mode (PWM/PFM) for the
DC/DC converter, output voltage of LDO1 (TPS65720 only) and shows the Status Flags related to DCDC1
and LDO1.
In the lower right corner of the window, all DCDC1/LDO1-related User Registers are displayed.
See the TPS65720 data sheet for detailed description on these registers.
9
SLVU324–March 2010 TPS65720EVM
Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated
Setup
www.ti.com
Figure 5. Software DCDC1/LDO1 View
The GPIO control window (see Figure 6) allows control of the fours GPIOs of the TPS65720/1. The GPIOs
can be configured as input or output. In addition, GPIO2 and GPIO3 can be configured as current sink to
drive an external LED.
In the lower right corner of the window, all GPIO-related User Registers are displayed.
See the TPS65720 data sheet for detailed description on these registers.
10 TPS65720EVM SLVU324–March 2010
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Table of contents
Other Texas Instruments Control Unit manuals
Texas Instruments
Texas Instruments TLV320DAC26EVM User manual
Texas Instruments
Texas Instruments TMS320TCI648 Series User manual
Texas Instruments
Texas Instruments LMZ14201 SIMPLE SWITCHER User manual
Texas Instruments
Texas Instruments TCAN1046V User manual
Texas Instruments
Texas Instruments TPS65253 User manual
Texas Instruments
Texas Instruments AWR1443 User manual
Texas Instruments
Texas Instruments TAS6424R-Q1 User manual
Texas Instruments
Texas Instruments HD3SS3220 User manual
Texas Instruments
Texas Instruments XIO2001 User manual
Texas Instruments
Texas Instruments TPS2398EBM User manual
Texas Instruments
Texas Instruments TPS5430 User manual
Texas Instruments
Texas Instruments TAS3208EVM-LC User manual
Texas Instruments
Texas Instruments bq2570 Series User manual
Texas Instruments
Texas Instruments TAS2770YFF User manual
Texas Instruments
Texas Instruments ADC12DJ5200RF User manual
Texas Instruments
Texas Instruments Tiris 2000 Series User manual
Texas Instruments
Texas Instruments INA901EVM-CVAL User manual
Texas Instruments
Texas Instruments TAS5086-5186V6EVM User manual
Texas Instruments
Texas Instruments TPS54362B EVM User manual
Texas Instruments
Texas Instruments DRV601EVM User manual
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
