Texas Instruments BQ25750 User manual
EVM User's Guide: BQ25750
BQ25750 Evaluation Module
Description
The BQ25750EVM evaluation module (EVM) is a
complete evaluation system for the BQ25750 IC, a
buck-boost battery charge controller with direct power
path control. The BQ25750 has a wide input range of
4.2 V – 70 V, a wide output voltage range of up to 70
V, and bi-directional capabilities.
The BQ25750EVM has a max input and output of 55
V and a max charge current of 10 A.
Get Started
1. Order the EVM on ti.com
2. Order the EV2400 to communicate with the EVM
3. Download the BQ25750 BQZ file
4. Download the BQ25750 EVM design files on
ti.com
Features
• Wide input voltage operating range: 4.2 V – 55 V
• Wide output operating range: up to 55 V with
CC/CV support for:
– 2 to 13–Cell Li-Ion
– 2 to 14–Cell LiFePO4
• Synchronous buck-boost DC/DC charge controller
with NFET drivers
– Adjustable switching frequency from 200 kHz to
600 kHz
– Optional synchronization to external clock
– Optional gate driver supply input for optimized
efficiency
• Resistor-programmable stand-alone with added
I2C mode
• Built in MPPT to maximize power from solar panel
arrays
• Power up from battery (reverse-mode) output 4 V
to 55 V
• High safety integration
– Adjustable input overvoltage and undervoltage
protection
– Output overvoltage and overcurrent protection
www.ti.com Description
SLUUCY7 – NOVEMBER 2023
Submit Document Feedback
BQ25750 Evaluation Module 1
Copyright © 2023 Texas Instruments Incorporated
1 Evaluation Module Overview
1.1 Introduction
The BQ25750EVM evaluates for applications that use greater than a 100 W USB input with the new USB-C
Power Delivery (PD) Extended Power Range (EPR) and up to 13 cell Li-Ion battery charging implementing
CC/CV profile. Typical applications include medical equipment, solar backup chargers, energy storage systems,
drones, cordless power and garden tools.
This EVM does not include the EV2400 or USB2ANY interface device and does not provide any electrical
isolation for the digital interfaces. EV2400 or USB2ANY can be ordered separately to evaluate the
BQ25750EVM and considering electrical safety is important when interfacing between the PC and EVM board.
When interfacing the EVM to the PC through the digital interfaces, digital isolators with isolation boundary is
recommended.
The BQ25750EVM does not have an isolation boundary and has smaller clearance and creep than normally
used on high-voltage boards. If the user applies high voltage to this board, all terminals are considered high
voltage and hazardous when live. Electric shock is possible when connecting the board to live wire. The board
must be handled by a professional with care. TI recommends the use of isolated test equipment with safety
protection features (such as overvoltage and overcurrent).
1.2 Kit Contents
This EVM kit includes:
• 1 BQ25750 EVM
1.3 Device Information
The BQ25750EVM evaluation module (EVM) is an evaluation system for the BQ25750 IC. The BQ25750 IC is a
buck-boost battery charge controller with direct power path control. The BQ25750 has a wide input range of 4.2
V – 70 V, a wide output voltage range of up to 70 V, and bi-directional capabilities.
The device offers high-efficiency battery charging with accurate charge current and charge voltage regulation
over a wide voltage range. The design also includes automatic charge preconditioning, termination, and charge
status indication. The device integrates loop compensation for the buck-boost converter, which provides a
high-density design with ease of use. In reverse mode, the device draws power from the battery and regulates
the SYS terminal voltage.
The device supports stand-alone charging mode through resistor programmable limits in addition to the I2C
host-controlled charging mode. Input current, charge current, and charge voltage regulation targets are set
through the ILIM_HIZ, ICHG and FB pins, respectively.
Evaluation Module Overview www.ti.com
2BQ25750 Evaluation Module SLUUCY7 – NOVEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
1.4 Texas Instruments High Voltage Evaluation User Safety Guidelines
WARNING
Always follow TI's set-up and application instructions, including use of all interface components within their
recommended electrical rated voltage and power limits. Always use electrical safety precautions to help verify
your personal safety and those working around you. Contact TI's Product Information Center http://ti.com/
customer support for further information.
Save all warnings and instructions for future reference.
WARNING
Failure to follow warnings and instructions can result in personal injury, property damage or death
due to electrical shock and burn hazards.
The term TI HV EVM refers to an electronic device typically provided as an open framed, unenclosed printed
circuit board assembly. It is intended strictly for use in development laboratory environments, solely for qualified
professional users having training, expertise and knowledge of electrical safety risks in development and
application of high voltage electrical circuits. Any other use and/or application are strictly prohibited by Texas
Instruments. If you are not suitably qualified, then you need to immediately stop from further use of the HV EVM.
1. Work Area Safety:
a. Keep work area clean and orderly.
b. Qualified observers must be present anytime circuits are energized.
c. Effective barriers and signage must be present in the area where the TI HV EVM and the interface
electronics are energized, indicating operation of accessible high voltages can be present, for the
purpose of protecting inadvertent access.
d. All interface circuits, power supplies, evaluation modules, instruments, meters, scopes, and other related
apparatus used in a development environment exceeding 50Vrms/75VDC must be electrically located
within a protected Emergency Power Off EPO protected power strip.
e. Use stable and non-conductive work surface.
f. Use adequately insulated clamps and wires to attach measurement probes and instruments. No
freehand testing whenever possible.
2. Electrical Safety:
a. As a precautionary measure, a good engineering practice to assume is that the entire EVM can have
fully accessible and active high voltages.
b. De-energize the TI HV EVM and all the inputs, outputs and electrical loads before performing any
electrical or other diagnostic measurements. Re-validate that TI HV EVM power has been safely de-
energized.
c. With the EVM confirmed de-energized, proceed with required electrical circuit configurations, wiring,
measurement equipment hook-ups and other application needs, while still assuming the EVM circuit and
measuring instruments are electrically live.
d. Once EVM readiness is complete, energize the EVM as intended.
WARNING
While the EVM is energized, never touch the EVM or the electrical circuits, as the electrical
circuits and EVM can be at high voltages capable of causing electrical shock hazard.
3. Personal Safety
a. Wear personal protective equipment e.g. latex gloves or safety glasses with side shields or protect EVM
in an adequate lucent plastic box with interlocks from accidental touch.
Limitation for safe use:
EVMs are not to be used as all or part of a production unit.
www.ti.com Evaluation Module Overview
SLUUCY7 – NOVEMBER 2023
Submit Document Feedback
BQ25750 Evaluation Module 3
Copyright © 2023 Texas Instruments Incorporated
1.4.1 General Safety Information
The following warnings and cautions are noted for the safety of anyone using or working close to the BQ25750
EVM. Observe all safety precautions.
Warning Caution
The BQ25750EVM circuit module can become hot during operation due to the
dissipation of heat. Avoid contact with the board. Follow all safety procedures
applicable to your laboratory.
CAUTION
Hot surface. Contact can cause burns. Do not touch!
Warning
The BQ25750EVM does not have an isolation boundary and has smaller clearance
and creep than normally used on high-voltage boards. If the user applies high
voltage to this board, all terminals are considered high voltage and hazardous
when live. Electric shock is possible when connecting the board to live wire. The
board must be handled by a professional with care. TI recommends the use of
isolated test equipment with safety protection features (such as overvoltage and
overcurrent).
Warning
High voltages that can cause injury exist on this evaluation module (EVM). Please
follow all safety procedures when working on this EVM. Never leave a powered
EVM unattended.
Warning High voltage can be present on board capacitors after power down. Check and
discharge all on-board energy reservoirs properly after EVM power down.
!
Caution Do not leave the EVM powered when unattended.
CAUTION
The communication interfaces are not isolated on the EVM. TI recommends the use of digital
isolators. Observe all high voltage safety precautions during testing.
CAUTION
Connections for a rated current must be made at the terminal block. Test points are not rated for the
board current.
CAUTION
The circuit module can be damaged by overtemperature. To avoid damage, monitor the temperature
during evaluation and provide cooling, as needed, for your system environment. Do not operate
beyond the current and voltage limits in Section 2.3.
CAUTION
Test equipment can be damaged by the application of external voltages. Check your equipment
requirements and use blocking diodes or other isolation techniques, as needed, to prevent damage
to your equipment.
CAUTION
The circuit module has signal traces, components, and component leads on the bottom of the board.
Exposed voltages, hot surfaces, or sharp edges can result in these areas. Do not reach under the
board during operation.
Evaluation Module Overview www.ti.com
4BQ25750 Evaluation Module SLUUCY7 – NOVEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
CAUTION
The default settings of the BQ25750 are not designed for all applications. Set the EVM settings
appropriately for test setup before device power up. Set all protections appropriately and limit current
for safe operations.
CAUTION
The board has no fuse installed and relies on the external voltage source current limit for circuit
protection.
www.ti.com Evaluation Module Overview
SLUUCY7 – NOVEMBER 2023
Submit Document Feedback
BQ25750 Evaluation Module 5
Copyright © 2023 Texas Instruments Incorporated
2 Hardware
2.1 Board Parameters
Table 2-1. Default Board Setup for BQ25750EVM
Description Value Unit
ACUV Input undervoltage 4.2 V
ACOV Input overvoltage 55 V
IIN Input current of the EVM 8 A
IOUT Output current of the EVM 10 A
FSW_SYNC Switching frequency of the power stage 250 kHz
Table 2-2. PCB and Mechanical Parameters
Value Unit
Board size (X dimension, or length) 112 mm
Board size (Y dimension, or width) 84 mm
IC + power stage max height 5 mm
Total copper layers 6 layer
Copper weight per layer 2 oz
Total board thickness 62 mil
2.2 IO and Jumper Descriptions
Table 2-3. Connector and Port Description
Jack Description
J1-VIN Input: positive terminal
J1-PGND Input: negative terminal (ground terminal)
J2-VSYS Charger system output voltage, typically connected to the system load
J2-PGND Ground
J3-VOUT Connected to battery pack output
J3-PGND Ground
J4-EXT_I2C Communication port for the USB2ANY
J5-I2C Communication port for the EV2400
J6-EXT_DRV Connection for external gate drive
J7-Power Connector Connection for VAC and BAT
J8-Communication Port Connection for EXT_DRV, /INT, I2C, /PG, and 3.3 V
Hardware www.ti.com
6BQ25750 Evaluation Module SLUUCY7 – NOVEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
Table 2-4. Jumper Description
Jumper Description Factory Default
JP1 Use JP1 to connect the default feedback resistor and set the charger to the default 7
cell battery. Installed
JP2 Use JP2 to connect a new feedback resistor to program a different cell count. Not installed
JP3 Use JP3 to connect external IOUT resistor. JP3 can be shorted to PGND to turn off
hardware output current limiting.
Not installed
JP4 Shunt JP4 to use default IOUT resistor. By closing JP4, the default IOUT current is
set to 10 A.
Installed
JP5 Shunt JP5 to bias TS. Installed
JP6 With JP5 shunted (REGN connected for voltage divider). Shunt JP6 to set TS status
to normal.
Installed
JP7 With JP5 shunted (REGN connected for voltage divider). Use JP7 to connect
external resistor to change TS status.
Not installed
JP8 Use JP8 to connect external FSW_SYNC resistor. Not installed
JP9 Shunt JP9 to use default FSW_SYNC resistor. By closing JP9, the default switching
frequency is set to 250 kHz.
Installed
JP10 Shunt JP10 to use default IIN resistor. By closing JP10, the maximum input current
is set to 8 A.
Installed
JP11 Use JP11 to connect external IIN resistor. JP11 can be shorted to PGND to turn off
hardware input current limiting.
Not installed
JP12
Use JP12 to select the gate driver source. Shunt pin1 to pin2 to use IC internal
LDO REGN output. Shunt pin2 to pin3 to use external gate drive supply. Maximum
external gate drive supply can be up to 11 V.
Pin1 and pin2 shunted
JP13 Shunt JP13 to enable controller in forward mode. Open JP13 to disable controller.
The /CE pin can also be used as a general purpose indicator.
Installed
JP14 Shunt JP14 to connect /INT to a pullup rail. Installed
JP15 Shunt JP15 to connect STAT1 to a pullup rail. The STAT1 pin can also be used as a
general purpose indicator.
Installed
JP16 Shunt JP16 to generate on board 3.3-V pullup rail. Installed
2.3 Recommended Operating Conditions
Table 2-5. Recommended Operating Conditions for BQ25750EVM
Description MIN TYP MAX UNIT
VIN (J1) Input voltage to the EVM 4.2 55(1) V
VOUT (J3) Output voltage of the EVM 3.3 55(1) V
IIN (J1) Input current of the EVM 10(3) (4) A
IOUT (J3) Output current of the EVM 10(3) A
Regulator output power Output power of the EVM 400(3) W
EXT_DRV (J6) Voltage applied to DRV_SUP pin of the regulator 4 11 V
EVM Operating Ambient
Temperature (TA) 25(2) °C
(1) Nodes on the EVM can have high spikes above the input voltage (in buck mode) or output voltage (in boost mode) level due to the
high di/dt and dv/dt electrical flow associated with switch-mode power supplies. Switch node voltage can swing up to input or output +
inductive spike level. High-side gate drives can swing up to switch node voltage + 11 V (DRV_SUP supply voltage dependent) + gate
drive inductive spike level. Observe safety precautions at all times.
(2) Connectors, bump-ons, and jumpers on the EVM are not good choices for evaluation under temperatures that greatly deviate from a
room temperature of 25°C. Please refer to the Bill of Materials (BOM) for temperature ratings of board components.
(3) TI recommends thermal monitoring (for example, using a thermal camera) if the power-stage output current > 5 A or total output power
> 100 W.
(4) The default EVM input current limit is set to 8 A through the IIN pin. The current-limiting feature can be turned off by setting the
EN_IIN_PIN bit to '0', changing the IIN pin resistor, or shorting the IIN pin to PGND through JP11.
www.ti.com Hardware
SLUUCY7 – NOVEMBER 2023
Submit Document Feedback
BQ25750 Evaluation Module 7
Copyright © 2023 Texas Instruments Incorporated
2.4 Equipment
TI recommends two ways to test the EVM. The first and preferred way to test the EVM is to use a four-quadrant
power supply. The second is to use a electronic load in constant voltage mode. Testing with a constant voltage
load is covered in Section 2.4.3. TI recommends the following list of equipment when testing with a four-quadrant
power supply.
1. Power Supplies:
A power supply capable of supplying 40 V at 8 A is required. This part can handle larger voltage and current,
however, larger power levels are not necessary for this procedure.
2. Load 1:
A Kepco load: BOP36-6M, DC 0 to ±36 V, 0 to ±6 A (or higher), or equivalent. When testing without a real
battery, connect 2000 uF of capacitance across the input.
3. Meters:
Six Fluke 75 multimeters, (equivalent or better) or: Three equivalent voltage meters and three equivalent
current meters.
4. Computer:
A computer with at least one USB port and a USB cable.
5. EV2400 Communication Kit
6. Software:
Download and properly install bqStudio.
2.4.1 Equipment Set Up
EV2400
USB
+
–
+
–
A
VAC
IAC
VBAT
IBAT
Op
onal Gate
Drive Supply
DMM
VAC
A
DMM
I2C
Use the following guidelines to set up the equipment:
1. Set power supply 1 for 23 V DC, 8 A current limit and then turn off the supply.
2. Connect the output of power supply 1 in series with a current meter to J1 (VIN and PGND).
3. Connect a voltage meter across J1 (VIN) and J1 (PGND).
4. Connect load 1 in series with a current meter to J3 (VBAT and PGND).
5. Connect a voltage meter across J5 (VBAT and PGND).
6. Set 23 V at KEPCO load output. Limit KEPCO to 6 A. Use load 2 to power EVM from the VOUT output.
7. Connect J5 to the EV2400. Connect J5 to the I2C PORT 2 on the EV2400.
8. Install the jumpers as indicated in IO and Jumper Descriptions.
Hardware www.ti.com
8BQ25750 Evaluation Module SLUUCY7 – NOVEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
9. Turn on the computer and load 2. Open the bqStudio software.
a. Select Charger and click the Next button.
b. Select Charger_1_00_BQ25750.bqz on the Select a Target Page.
c. Click Field View after selecting the target device and then click the Read Register button.
10. Set WATCHDOG and EN_CHG to disabled.
11. Set ICHG_REG to 4000 mA and IPRECHG to 1000 mA in the 16 Bit Registers field.
12. Turn on power supply 1, measure:
V(J1(VAC)) = 23 V ± 0.5 V
I(J1(IAC)) = 4.1 A ± 0.5 A
V(J3(VBAT)) = 23 V ± 0.5 V
I(J3(IBAT)) = 3.9 A ± 0.5 A
13. Set power supply 1 for 40 V, measure:
V(J1(VAC)) = 40 V ± 0.5 V
I(J1(IAC)) = 2.4 A ± 0.5 A
V(J3(VBAT)) = 23 V ± 0.5 V
I(J3(IBAT)) = 3.9 A ± 0.5 A
www.ti.com Hardware
SLUUCY7 – NOVEMBER 2023
Submit Document Feedback
BQ25750 Evaluation Module 9
Copyright © 2023 Texas Instruments Incorporated
14. Set power supply 1 for 19 V, measure:
V(J1(VAC)) = 19 V ± 0.5 V
I(J1(IAC)) = 5.0 A ± 0.5 A
V(J3(VBAT)) = 23 V ± 0.5 V
I(J3(IBAT)) = 3.9 A ± 0.5 A
Use the following guidelines to test the BQ25750 EVM power path:
1. Disconnect the power supply from J1 (VIN and PGND) and disconnect Load 1 from J3 (VOUT and PGND).
2. Connect the output of power supply #1 to J3 (VOUT and PGND).
3. Set power supply 1 for 20 V DC, 8 A current limit and then turn off power supply.
4. Connect a voltage meter across J2 (VSYS) and J2 (PGND).
5. Turn on power supply 1, measure V(J2(VSYS)) = 20 V ± 0.5 V.
2.4.2 Equipment - Using a CV Load
The following list of equipment is recommended when testing with a constant voltage electronic load.
1. Power Supplies:
A power supply capable of supplying 40 V at 8 A is required. This part can handle larger voltage and current,
however, larger power levels are not necessary for this procedure.
2. Load 1:
Kikusui PLZ164WA 0-150 V, 0-33 A when testing without a real battery, connect 2000 uF of capacitance
across the input.
3. Meters:
Six Fluke 75 multimeters (equivalent or better) or three equivalent voltage meters and three equivalent
current meters.
4. Computer:
A computer with at least one USB port and a USB cable.
5. EV2400 Communication Kit
6. Software:
Download and properly install bqStudio.
Hardware www.ti.com
10 BQ25750 Evaluation Module SLUUCY7 – NOVEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
This manual suits for next models
1
Table of contents
Other Texas Instruments Control Unit manuals
Texas Instruments
Texas Instruments TPS61280-585 User manual
Texas Instruments
Texas Instruments DRV8803 User manual
Texas Instruments
Texas Instruments TLC6A598 User manual
Texas Instruments
Texas Instruments TPS55165Q1-EVM User manual
Texas Instruments
Texas Instruments BOOSTXL-ADS1219 BoosterPack User manual
Texas Instruments
Texas Instruments ADS8555EVM-PDK User manual
Texas Instruments
Texas Instruments TPS79301EVM User manual
Texas Instruments
Texas Instruments PCM1681 User manual
Texas Instruments
Texas Instruments TLV320AIC3109EVM-K User manual
Texas Instruments
Texas Instruments PGA2505EVMV2 User manual
Texas Instruments
Texas Instruments LP8864 User manual
Texas Instruments
Texas Instruments Tiris 2000 Series User manual
Texas Instruments
Texas Instruments MSP-EXP430G2 User manual
Texas Instruments
Texas Instruments TUSB564RNQ User manual
Texas Instruments
Texas Instruments ADS1x7xEVM-PDK User manual
Texas Instruments
Texas Instruments TPS53515 User manual
Texas Instruments
Texas Instruments TLC5540 User manual
Texas Instruments
Texas Instruments TRF7970A BoosterPack User manual
Texas Instruments
Texas Instruments BOOSTXL-TPS652170 User manual
Texas Instruments
Texas Instruments UCD90120 User manual
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
