Texas Instruments THVD1454EVM User manual

EVM User's Guide: THVD1454EVM

THVD1454EVM User's Guide

ABSTRACT

This document is the EVM User’s guide for the THVD1454EVM which provides a quick way to evaluate the TI

THVD1454, a half duplex RS-485 transceiver with selectable data rate and switchable integrated termination

resistors, in the VSON (DRC) package.

Table of Contents

1 Introduction.............................................................................................................................................................................2

2 Board Description...................................................................................................................................................................4

3 Board Component Overview..................................................................................................................................................4

4 Powering the Board................................................................................................................................................................6

5 Operation of THVD1454EVM..................................................................................................................................................7

5.1 Default Operation............................................................................................................................................................... 7

5.2 Potential Modifications....................................................................................................................................................... 7

6 Design Documents................................................................................................................................................................. 9

6.1 Schematics.........................................................................................................................................................................9

6.2 Layout...............................................................................................................................................................................11

6.3 Bill of Materials.................................................................................................................................................................13

7 References............................................................................................................................................................................ 13

Trademarks

All trademarks are the property of their respective owners.

www.ti.com Table of Contents

SLLU365 – JANUARY 2023

Submit Document Feedback

THVD1454EVM User's Guide 1

1 Introduction

About This Manual

Figure 1-1. Top View of THVD1454EVM

Introduction www.ti.com

2THVD1454EVM User's Guide SLLU365 – JANUARY 2023

Submit Document Feedback

Figure 1-2. Bottom View of THVD1454EVM

Information About Cautions and Warnings

The information in the warning statement is provided for personal protection and the information in the caution

statement is provided to protect the equipment from damage. Read each caution and warning statement

carefully.

This EVM contains components that can potentially be damaged by electrostatic discharge. Always transport

and store the EVM in its supplied ESD bag when not in use. Handle using an antistatic wristband. Operate on an

antistatic work surface. For more information on proper handling, see Electrostatic Discharge (ESD).

www.ti.com Introduction

SLLU365 – JANUARY 2023

Submit Document Feedback

THVD1454EVM User's Guide 3

2 Board Description

Features

• Ready to Use out of Box with THVD1454 Pre-Installed

• Two 10 uF and Two 47 uF Decoupling Caps Pre-Installed on VCC to GND and GND to EARTH Connections

• Two Resistor Pads to create resistive link between GND and EARTH

• One 4x2 Header Connection for Feature Control Signals

• External Termination Resistor and Capacitor Pads on shared bus

• Common Mode Voltage Connection Points Located at J11 and J12

3 Board Component Overview

The THVD1454EVM is ready to operate directly out of box with a THVD1454 installed at U1. All the Signal

and Power Jumpers/Inputs (J1 – J12) come pre-installed on board. See Table 3-1 for component overview for

Jumpers.

Table 3-1. Power Jumpers/Inputs (J1 – J12)

Jumper ID Function Package Comment Installed?

J1 “R” Pin output 4x2 Header N/A Y

J2 “/RE” Pin Input 4x2 Header N/A Y

J3 “DE” Pin Input 4x2 Header N/A Y

J4 “D” Pin Input 4x2 Header N/A Y

J5 VCC Terminal 3-Pin Terminal Block N/A Y

J6 Control Signal Header 4x2 Header N/A Y

J7 Bus Header #1 4x1 Header Between Series Resistor

and IC

J8 Bus Header #2 4x1 Header Between Series Resistor

and Terminal

J9 Differential Bus

Connection Terminal

3-Pin Terminal Block N/A Y

J10 “A” Line Common Mode

Input

4x1 Header N/A Y

J11 “B” Line Common Mode

Input

4x1 Header N/A Y

J12 Differential Bus Common

Mode Input

4x1 Header N/A Y

Resistor Pad IDs (R1-R20), function, package, comment, and default installation status are shown inTable 3-2.

Table 3-2. Resistor Pad IDs (R1-R20)

Resistor ID Function Package Comment Installed?

R1 0 Ohm Series Resistor 0603 "R" Pin Y

R2 Pull-Up Resistor 0603 "R" Pin N

R3 LED Current Limiting

Resistor

0603 "R" Pin LED Y

R4 0 Ohm Series Resistor 0603 "/RE" Pin Y

R5 Pull-Down Resistor 0603 "/RE Pin" N

R6 Pull-Up Resistor 0603 "/RE Pin" N

R7 0 Ohm Series Resistor 0603 "DE Pin" Y

R8 Pull-Up Resistor 0603 "DE Pin" N

R9 Pull-Down Resistor 0603 "DE Pin" N

R10 0 Ohm Series Resistor 0603 "D Pin" Y

R11 Pull-Up Resistor 0603 "D Pin" N

R12 Pull-Down Resistor 0603 "D Pin" N

Board Description www.ti.com

4THVD1454EVM User's Guide SLLU365 – JANUARY 2023

Submit Document Feedback

Table 3-2. Resistor Pad IDs (R1-R20) (continued)

Resistor ID Function Package Comment Installed?

R13 LED Current Limiting

Resistor

0603 "D Pin LED" Y

R14 GND to EARTH Resistor 0603 N/A N

R15 LED Current Limiting

Resistor

0603 "VCC LED" N

R16 Termination Resistor Pad 0805 N/A N

R17 0 Ohm Series Resistor 0603 "A Pin" Y

R18 0 Ohm Series Resistor 0603 "B Pin" Y

R19 Common Mode Resistor

"A Pin"

0603 N/A N

R20 Common Mode Resistor

"B Pin"

0603 N/A N

Capacitor Pad IDs (C1 - C10), function, package, comment, and default installation status are shown in Table

3-3.

Table 3-3. Capacitor Pad IDs (C1 - C10)

Capacitor ID Function Package Comment Installed?

C1 Capacitive Load on "R"

0603 N/A N

C2 IC HF Decoupling

Capacitor

0603 N/A Y

C3 GND to Earth 47uF

Decoupling Capacitor

0805 N/A Y

C4 VCC to GND 47uF

Decoupling Capacitor

0805 N/A Y

C6 VCC to GND 10uF

Decoupling Capacitor

0805 N/A Y

C7 Earth to GND 10uF

Decoupling Capacitor

0805 N/A Y

C8 Termination Capacitor Pad 0805 N/A N

C9 "A" Pin Common Mode

Decoupling Capacitor

0603 N/A Y

C10 "B" Pin Common Mode

Decoupling Capacitor

0603 N/A Y

Other component IDs, function, package, comment, and default installation status are shown in Table 3-4.

Table 3-4. Other component IDs

Other Component ID Function Package Comment Installed?

D1 LED indicator for Data

Reception at "R" pin

Custom "Red" Y

D2 LED Indicator For Data

Transmission at "D" pin

Custom "Green" N

D3 LED Indicator for Board

Power

Comment "Blue" Y

U1 Main EVM IC DRC N/A Y

www.ti.com Board Component Overview

SLLU365 – JANUARY 2023

Submit Document Feedback

THVD1454EVM User's Guide 5

4 Powering the Board

Powering the THVD1454EVM is a quick process. To power on the board have top side of board facing upwards

with J5 at the top of the EVM. From left to right the power terminal pins of J5 are connected to Earth, GND, and

VCC respectively - this is also noted on the EVM.

If the test setup includes an Earth or Chassis connection, connect this to the left pin of J5. If no Earth or Chassis

connection exist in the test setup connect this pin to GND. Next connect the GND connection to the center pin

of J5 as this is what the THVD1454 references as its GND connection. Finally connect the positive terminal of

a 3.3V to 5V supply voltage to the right most pin on J5. The board is now ready to be powered on; this is done

correctly when the blue LED "D3" lights up.

The Proper orientation of the J5 Terminal Block is shown in Figure 4-1.

Figure 4-1. Power Connection Block View: J5

Powering the Board www.ti.com

6THVD1454EVM User's Guide SLLU365 – JANUARY 2023

Submit Document Feedback

5 Operation of THVD1454EVM

5.1 Default Operation

After powering up the EVM with instructions listed Powering The Board, the EVM is ready to ready to operate

without modification. If all pins, besides VCC and GND, are left floating after power up the following each pin is in

the states listed in Table 5-1.

Table 5-1. Default Pin States THVD1454

Pin on THVD1454 Associated Jumper Default State Comment

R J1 Hi-Z /RE is pulled high by default

leaving RX disabled

/RE J2 Logic High Internal pull-up leaves /RE ~ VCC

by default. RX disabled

DE J3 Logic Low Internal pull-down leaves DE

~GND by default. TX disabled

D J4 Logic High Internal pull-up leaves "D" high -

preventing floating input on data

input pin

TERM J6 Logic Low Internal pull-down disables

integrated termination resistor by

default

B J7, J8, and J9 Hi-Z Driver disabled by default.

A J7, J8, and J9 Hi-Z Driver Disabled by default

SLR J6 Logic Low Slew Rate Control is disabled

by default allowing for maximum

speeds of 20Mbps

To transmit data under the default setup see Table 5-2.

Table 5-2. TX Function Table

DE (J3) D (J4) A (Output) B (Output)

Low X Hi-Z Hi-Z

High Low Low High

High High High Low

Under the default conditions the A and B pins are unterminated and can handle data up to a speed of 20Mbps.

To receive data under the default setup see receiver function table below. For best results on reception DE

should be held low to disable the driver.

Table 5-3. RX Function Table

/RE (J2) VA - VB (J7, J8, and J9) R (J1)

High X Hi-Z

Low ≥ -45 mV High

Low ≤ -200 mV Low

Low -45 mV ≤ VA - VB ≤ -200 mV Indeterminate

For potential modifications and deviations away from default setup, please see Potential Modifications .

5.2 Potential Modifications

With a understanding of the board in its default state there are a few modifications that can be made either via

the header blocks or by adding addition components.

Figure 5-1 shows the control header J6, which with the addition of two shunts can control the Slew Rate Control

(SLR) feature and Integrated Termination (TERM) features.

www.ti.com Operation of THVD1454EVM

SLLU365 – JANUARY 2023

Submit Document Feedback

THVD1454EVM User's Guide 7

Figure 5-1. Control Block View: J6

The J6 header has pin one on the bottom right hand corner and pin two on the top right hand corner. The pins

increment up from right to left with the top row even pin numbers and the bottom row odd numbers. A signal map

is shown in Table 5-4.

Table 5-4. J6 Pin Mapping

J6 Pin # SIGNAL

1 SLR

2 SLR

3 VCC

4 GND

5 TERM

6 TERM

7 VCC

8 GND

A function table of SLR and TERM is shown in Table 5-5.

Table 5-5. J6 Function Table

Pin | Jumper Pin State Function Comment

TERM | J6-5, J6-6 Low Integrated Termination Disabled For non-terminated nodes

TERM | J6-5, J6-6 High Integrated Terminatino Enabled Terminated with 120Ω between A

and B.

SLR | J6-1, J6-2 Low Slew Rate Control Disabled Max Speed is 20Mbps

SLR | J6-1, J6-2 High Slew Rate Control Enabled Max Speed is 500Kbps

Beyond the controllable features accessed through J6 there are also pads for external pull-up, pull-down, and

capacitive loads available on J1, J2, J3, and J4. For typical applications capacitive loads are placed on "R"

pin and the other pins may or may not have external pull-up or pull-down resistors. All the pads are in 0603

packages and can be varied based on customers testing needs.

The final modifications are around the differential bus pins - A and B. To help simulate capacitive loading of

a cable a 0805 termination capacitor pad, ID = C8, is available between A and B pins. The option to add an

external termination resistance is also possible with a 0805 pad, ID = R16. This external termination when

paired with the integrated termination resistor can allow for quick measurements of power measurements on a

terminated bus. The power testing can be expanded with the addition of common mode loading resistances R19

and R20.

Operation of THVD1454EVM www.ti.com

8THVD1454EVM User's Guide SLLU365 – JANUARY 2023

Submit Document Feedback

6 Design Documents

6.1 Schematics

Figure 6-1. Schematic - No Schematic Markings

www.ti.com Design Documents

SLLU365 – JANUARY 2023

Submit Document Feedback

THVD1454EVM User's Guide 9

Figure 6-2. Schematic - DNI Markings Shown

Design Documents www.ti.com

10 THVD1454EVM User's Guide SLLU365 – JANUARY 2023

Submit Document Feedback

Table of contents

Other Texas Instruments Computer Hardware manuals

Texas Instruments

Texas Instruments TMS320C6000 DSP User manual

Texas Instruments

Texas Instruments TMS320C2 Series User manual

Texas Instruments

Texas Instruments TPA6135A2 EVM User manual

Texas Instruments

Texas Instruments LMH0318 Manual

Texas Instruments

Texas Instruments DRV603EVM User manual

Texas Instruments

Texas Instruments TMS320*2801 Series User manual

Texas Instruments

Texas Instruments TRF3722 EVM User manual

Texas Instruments

Texas Instruments BT-MSPAUDSOURCE-RD User manual

Texas Instruments

Texas Instruments bq2416063EVM User manual

Texas Instruments

Texas Instruments TRIS TMS37122 User manual

Texas Instruments

Texas Instruments AM335 Series Guide

Texas Instruments

Texas Instruments Tiva C Series User manual

Texas Instruments

Texas Instruments BQ25185EVM User manual

Texas Instruments

Texas Instruments TMS320C6000 DSP User manual

Texas Instruments

Texas Instruments UCD3138PFCEVM-026 User manual

Texas Instruments

Texas Instruments SimpleLink CC1312PSIP User manual

Texas Instruments

Texas Instruments TPS65910A Series User manual

Texas Instruments

Texas Instruments DLPLCRC910EVM User manual

Texas Instruments

Texas Instruments TMS320C3x User manual

Texas Instruments

Texas Instruments TMS320C642x DSP User manual

Texas Instruments

Texas Instruments TPS7H4003EVM User manual

Texas Instruments

Texas Instruments AM1808 User manual

Texas Instruments

Texas Instruments MSP430FG4618 User manual

Texas Instruments

Texas Instruments DAC8803/14 EVM User manual

Popular Computer Hardware manuals by other brands

EMC2

EMC2 VNX Series Hardware Information Guide

Panasonic

Panasonic DV0PM20105 Operation manual

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 user manual

Gigabyte

Gigabyte B660M DS3H AX DDR4 user manual

Raidon

Raidon iT2300 Quick installation guide

National Instruments

National Instruments PXI-8186 user manual

Hauppauge

Hauppauge WinTV-HVR-2250 Quick installation guide

Kontron

Kontron CP6002 user guide

Manhattan

Manhattan 702843 user manual

Aphex

Aphex 230 instruction manual

AMD

AMD Phenom II Product data sheet

Intel

Intel NUC 12 Pro user guide

dbx

dbx Zone Pro 1260 user manual

Galaxy

Galaxy GHDX2-2430S-24F4D Installation and hardware reference manual

Intel

Intel AXXRMFBU4 Quick installation user's guide

Kontron

Kontron DIMM-PC/MD product manual

ST X-NUCLEO-SAFEA1B How to use

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 installation manual