Tepex PLFS 50 LED-4 User manual

Doc. No.: TEPEx.RS.099

Ver: 1

Date: 06. 2018.

PLFS 50 LED-4

Upute za uporabu

User manual

U P O Z O R E N J E

Upute za uporabu sadrže osnovne informacije o proizvodu.

Montaža, instaliranje, uporaba i održavanje trebaju biti

izvedeni prema ovoj Uputi kako bi bio osiguran siguran rad

unutar nazivnih karakteristika. Ovu Uputu nadopunjuju

nacionalni Pravilnici i norme. Odgovorna osoba korisnika je

dužna osigurati njihovo provođenje. Neprovođenje može

umanjiti protueksplozijsku zaštitu uređaja i dovesti u

opasnost ljude, imovinu i okoliš. Svako neispravno i

nedozvoljeno postupanje kao i nepoštivanje odredbi ove

Upute isključuje svaku odgovornost proizvođača.

Prije ugradnje/puštanja u pogon:

-Pažljivo pročitati cijelu Uputu za uporabu,

-Izvršiti odgovarajuću obuku odgovornog osoblja,

-Provjeriti da je sadržaj ove Upute u potpunosti

razumljiv odgovornim osobama,

-Uvjeriti se da su primijenjeni svi zahtjevi nacionalnih Pravilnika

i posebne sigurnosne mjere ukoliko postoje.

U slučaju nejasnoća:

-Kontaktirati proizvođača.

Tijekom pogona:

-Osigurati da ove Upute za uporabu i druge radne upute

korisnika budu vidljivo istaknute i dostupne odgovornom

osoblju cijelo vrijeme,

-Provjeravati provođenje ove Upute i svih drugih

sigurnosnih uputa korisnika.

W A R N I N G

The user manual contains basic information about the

product. Mounting, installation, usage and maintenance

should be carried out under this user manual to provide and

ensure safe operation within the nominal characteristics. This

user manual complement national Regulation and Standards.

The responsible person shall ensure their implementation.

Failure off implement this user manual can reduce explosion

protection and endanger people, property and the

environment. Any improper and illegal actions as well as non-

compliance with the provisions of this user manual excludes

all responsibility by manufacturer side.

Before installation/commissioning:

-Carefully read all instructions,

-Execute proper training of responsible personnel,

-Check that the contents of these instructions is fully

understandable by the responsible personnel,

-Make sure that all the requirements and national Regulations as

well as all special security measures are applied.

In lack of understanding:

-Contact the manufacturer.

During operation:

-Ensure that this user manual and other work instructions are

available to the responsible staff at all times,

-Check the implementation of these instructions and all other

safety user’s instructions.

Medarska 69, Zagreb, Croatia

XMade in Croatia

tel. 00385 49 222 900

fax. 00385 49 426 450

e-mail: [email protected]

web: www.tepex.hr

0722

SADRŽAJ:

1. Namjena………………….……………….……………….……………….

2. Sukladnost proizvoda….………………………………………………

3. Tehnički podaci…………...……………………………………………..

4. Tipna oznaka………………….……………………………………………

5. Montaža………………………...…………………………………………..

6. Dimenzije……..................................................................

7. Pregled, održavanje, popravak, obnavljanje…………………

8. Rezervni dijelovi ……………….…….………………………………….

9. Odgovornost i ovlaštenja…………………..………………………..

10. Skladištenje i transport….……………………………………………

11. Jamstvo proizvođača………….……………………………………….

12. Označavanje……………………………………………………………….

CONTENTS:

1. Purpose…………………………………...…………....………………….

2. Product conformity………..………..………………………………..

3. Technical data……………………………………………………………

4. Types …………………………….…………………………………………..

5. Mounting………………………….………………………………..........

6. Dimensions…………………………………………………………….....

7. Inspection, maintenance, repair and overhaul……………

8. Spare parts.………………………………………………………………..

9. Responsibility and authorization.……………………………….

10. Storage and transport…………………………………………………

11. Manufacturer's warranty.…………………………………………..

12. Marking……..………………………………………………………........

1. NAMJENA

Protueksplozijski zaštićena ovjesna svjetiljka PLFS 50 LED-4

namijenjena je za upotrebu u industrijskim prostorima na

mjestima s potencijalno eksplozivnom atmosferom plinova,

para i prašina u zonama opasnosti 1, 2, 21, 22 sukladno normi

EN 60079-10-1/-2:2015.

2. SUKLADNOST PROIZVODA

Konstrukcija svjetiljke sukladna je s normama EN 60598-1 i svim

povezanim normama.

Proizvod je sukladan Pravilniku o opremi i zaštitnim sustavima

namijenjenim za uporabu u potencijalno eksplozivnim

atmosferama, NN br. 34/16.

Proizvod je sukladan ATEX Direktivi 2014/34/EU i normama:

-EN 60079-0:2012+A11:2013,

-EN 60079-7:2015,

-EN 60079-18:2015,

-EN 60079-31:2014.

Proizvod je razvijen, proizveden i ispitan prema postojećem

stanju tehnike sukladno normama EN ISO 9001:2015,

EN ISO 80079-34:2011 i EN ISO 14001:2015.

Proizvod je sukladan LVD Direktivi 2014/35/EU.

Proizvod je sukladan RoHS Direktivi 2011/65/EU.

Proizvod je sukladan EMC Direktivi 2014/30/EU.

3. TEHNIČKI PODACI

Certifikat

EXA 18 ATEX ….

Oznaka kategorije i

protueksplozijske zaštite

uređaja:

II 2G Ex db mb op is IIC T6 Gb

II 2D Ex tb op is IIIC T80°C Db

Temperatura okoline:

-40°C ≥ +40°C

Mehanička zaštita:

IP 66

Otpornost na udar:

IK 08

Klasa zaštite:

I (PE - zaštitno uzemljenje)

Nazivni napon Un:

230 V AC, 50 Hz

Radni napon:

220 - 240 V ± 10%, 50......60 Hz

Nazivna snaga Pn:

80 W

Faktor snage:

>0,95

LED izvor:

CLU058-1825C4, CITIZEN

ELECTRONICS CO. LTD

OVP zaštita:

IEC 61000-4-5, EN 62031 3kV/1min

-udarni prenapon 8/20μs 6kV/3kA

1. PURPOSE

Explosion protected pendant light fitting type PLFS 50 LED - 4, is

intended for general lighting in industrial areas with potentially

explosive atmosphere Zones 1, 2, 21, 22 in accordance with

EN 60079-10-1/-2:2015. The quality of the materials ensures

compliance with standard functionality in standard industrial

atmosphere.

For special requirements please contact the manufacturer.

2. PRODUCT CONFORMITY

The product complies with the standards:

-EN 60079-0:2012 / A11:2013,

-EN 60079-7:2015,

-EN 60079-18:2015,

-EN 60079-31:2014.

The product has been developed, manufactured and tested according

to the existing state of technique accordance with the

standards EN ISO 9001:2015 and EN ISO 80079-34:2011 and

EN ISO 14001:2015.

The product is in compliance with the ATEX Directive 2014/34/EU.

The product is in compliance with the LVD Directive 2014/35 EU.

The product is in compliance with the RoHS Directive 2011/65 EU.

The product is in compliance with EMC Directive 2014/30/EU.

3. TECHNICAL DATA

Certificate:

EXA 18 ATEX ….

Category and

explosion protection:

II 2G Ex db mb op is IIC T6 Gb

II 2D Ex tb op is IIIC T80°C Db

Ambient temperature:

-40°C ≥ +40°C

Mechanical protection:

IP66

Resistance to shock:

IK 08

Class of protection:

I (PE - protective earthing)

Rated voltage Un:

230 V AC, 50 Hz

Service voltage:

220 - 240 V ± 10%, 50......60 Hz

Rated power Pn:

80 W

Rated current In:

130 mA

Power factor:

>0,95

LED light source:

CLU058-1825C4, CITIZEN

ELECTRONICS CO. LTD

LED driver:

HBG-100P-60 MEANWELL Co.Ltd.

OCP zaštita:

2,5A T, IEC 60127

OTP zaštita:

Tsmax=80°C, povratno, IEC 60730-1

Svjetlosni tok:

10701 lm pri tamb=25°C

Temperatura boje

svjetlosti:

4000 K

Indeks uzvrata boje (CRI):

>80

Očekivana životna dob

LED-a:

50 000 radnih sati

pri tamb=40°C – L90/B10

Priključne stezaljke:

-stezaljke za priključak faznih i

neutralnog vodiča

L1, L2, L3, N; 2 x 2,5 mm2 max.

jednožični, višežićni

-unutrašnja stezaljka za

uzemljenje - PE; 2 x 6 mm2 max.

višežični

-vanjska stezaljka za uzemljenje -

2 x 6 mm2 max. fleksibilni

-moment pritezanja vijaka

priključne stezaljke 1,2 Nm

Uvodi:

-dva uvoda ISO 25, u skladu s EN

60423:2007

Ex e uvodnica i čep:

- jedna Ex eb II Gb kabelske

uvodnice M25x1,5 za promjere

kabela

Ø7-15 mm,

i jedan Ex eb II Gb čep M20x1,5

sukladno EN 50262, sastavni su

dijelovi svjetiljke

Momenti pritezanja:

Pritisna matica Ex e uvodnice

2,5 Nm

Tijelo Ex e uvodnice i čepa

3,5 Nm

Masa:

cca 11,6 kg

LED driver:

HBG-100P-60 MEANWELL Co.Ltd.

OVP protection:

IEC 61000-4-5, EN 62031 3kV/1min

impulse overvoltage 8/20μs 6kV/3kA

OCP protection:

2,5A T, IEC 60127

OTP protection:

Tsmax=80°C, resettable

Rated luminous flux:

10701 lm at Tamb = 25°C

Light colour:

4000 K

Refractive index(CRI):

>80

Estimated service life:

50 000 working hours

Tamb = 25°C L90/B10

Connection terminal:

- terminals for phase and neutral

conductors L1, L2, L3, N; max 2 x 2,5

mm2 sol(r), sol(s), f

-terminal for protective earthing -PE;

max 2 x 6 mm2 sol(s), f

-terminal for external grounding,

equipotential bounding

- max 2 x 6 mm2 sol(s) , f

- torque screw for terminals is 1,2

Cable entries:

2xISO25

Ex e cable gland and

plug:

One Ex eb II 2G / II 2D

cable glands M25x1,5

for cable Ø7-15 mm, and one

Ex eb II 2G / II 2D plug M25x1,5

are integral parts of lamps

Tightening torques

values:

Pinch Nut of the Ex e cable glands:

2.5 Nm

Body of the Ex e glands and plug:

3.5 Nm

Weight:

Cca 11,6 kg

4. TIPNA OZNAKA

4. TYPES

Svjetiljka ovjesna PLFS 50 LED-4

Pendant light fitting PLFS 50 LED-4

5. MONTAŽA

5. INSTALATION

Montaža i instaliranje svjetiljke se izvodi prema podacima na

natpisnim pločicama na svjetiljci, ovim i dodatnim uputama

proizvođača, nacionalnim Propisima i Pravilnicima, kao i prema

općenito priznatim pravilima tehnike. Samo uz taj uvjet osigurana je

tipnim certifikatom potvrđena protueksplozijska zaštita svjetiljke.

Kvaliteta upotrijebljenih materijala jamči funkcionalnost sukladnu

normi, u «normalnoj» industrijskoj atmosferi. Za posebne uvjete

pogona molimo kontaktirati proizvođača.

Montaža svjetiljke na podlogu vrši se preko nosača vijčanim

priborom M6.

Montaža svjetiljke na cijev vrši se preko jednog limenog nosača i

obujmice vijčanim priborom M6 koji se isporučuje uz svjetiljku.

Otvaranje kućišta se vrši odvrtanjem četiri vijka M5x25. Priključni

kabel se uvodi u kućište kroz predviđene uvodnice. Pri tome treba

provjeriti da su kabeli čisti i neoštećeni. Posebnu pažnju treba

posvetiti odabiru unutarnjeg brtvenog prstena uvodnice prema

Installation and putting into operation have to be done according to

technical and certification data on warning label on lamp, this user

manual, national regulations and laws. Only with that, explosion-

proof protection of bulkhead light fitting is ensured with EC-type

examination certificate.

Installation of lamp (on wall or ceiling) is done with steel

brackets with M6 screws.

Opening of Ex e enclosure is done by unscrewing four screws

M5x25. Special attention must be dedicated to selection of inner

gasket sealing ring of Ex e cable glands according to diameter of

connecting cable. Pressure nut and intermediate gland must be

tightened with nominal torque. Unused cable entries must be

closed with plug. The electric connecting is performing by

connecting power supply cable (L, NE, PE) on the connection

terminals and terminal for internal grounding.

vanjskom promjeru kabela. Pritisnu maticu uvodnice i tijelo

uvodnice treba pritegnuti nazivnim momentom. Neiskorišteni uvod,

na isti način, obavezno treba zatvoriti čepom. Zatvaranje kućišta se

izvodi na opisani način, suprotnim redoslijedom radnji.

The closing of the Ex e enclosure should be done by a reverse

sequence of action.

6. DIMENZIJE

6. DIMENSIONS

7. PREGLED, ODRŽAVANJE, POPRAVAK I OBNAVLJANJE

7. INSPECTION, MAINTENANCE, REPAIR AND OVERHAUL

Potrebno je obavljati preglede i održavati sve dijelove uređaja

o kojima ovisi protueksplozijska zaštita sukladno normi EN

60079-17:2014, općim i posebnim uputama proizvođača i

Pravilnicima korisnika, a naročito:

da su kućište, svi dijelovi kućišta, zaštitno staklo i

brtve bez puknuća i oštećenja,

da je kućište potpuno zatvoreno sklopom zaštitnog

stakla,

da su uvodnica, čep, vijci kutnika brtve, vijak stezaljke

za uzemljenje pritegnuti nazivnim momentom.

Popravak, obnavljanje ili pregradnju kućišta obavlja

proizvođač ili od proizvođača ovlaštena pravna osoba,

originalnim dijelovima prema proizvodnoj dokumentaciji, a sve

sukladno normi EN 60079-19:2011.

Ukoliko popravak i/ili obnavljanje i/ili pregradnju vrši treća

osoba, prestaje svaka odgovornost proizvođača za proizvod, a

izjava sukladnosti proizvođača postaje nevažeća.

Inspections are carried out in accordance with IEC 60079-17,

general and special conditions of manufacturer and users

Regulations and includes supervision of parts on which the

explosion protection depends, especially:

that the housing, all part of housing, protective glass and

gasket are without rupture and damage,

that the housing is completely closed with set of protective

glass

that the cable gland, plug, connecting terminals, screws of

protective grid are tightened with nominal torque.

All the repairs must be performed by the manufacturer or the

manufacturer's authorized personal using the original parts

according to the product documentation, all in accordance

with EN 60079-19:2011.

If repair or any other procedure are performed on the product

by unauthorized person, all producer responsibility for the

product and the warranty and the manufacturer's Declaration

of conformity becomes invalid.

420±5

228±1

8. REZERVNI DIJELOVI

8. SPARE PARTS

Spare parts

Description

Code

Accessories

Description

Code

PLFS LED 50

The glass

protective

framework,

set

PLFS LED

10-120

PLFS LED 50

Protection

grid, set

PLFS LED 10-

130

PLFS-T

Ex-e terminal

chamber

cover,

set

PLFS 10-150

PLFS-T

External

reflector,

set

PLFS

20-100

Ex-e cable

gland ISO25,

set

SPU 25

PLFS-T lamp

holder for

lamppost

ϕ1 1/2'',

set

PLFS

20-120

Ex-e plug

ISO25,

set

SPC 25

PLFS 50 LED-4

bracket for

wall

mounting,

set

PLFS 50-4

20-130

Housing and

LED driver

assembly

PLFS 50 LED-4

Driver

assembly

PLFS 50 LED-

4 source

assembly

PLFS 50 LED-4

source

assembly

9. ODGOVORNOSTI I OVLAŠTENJA

9. RESPONSIBILITY AND AUTHORIZATION

Ova Uputa predstavlja najvažniju informaciju o proizvodu.

Nadopunjuju ju odgovarajući nacionalni zakoni i propisi.

Proizvodnja, uporaba, certifikacija i nadzor određene su na

nacionalnoj razini Pravilnikom o najmanjim zahtjevima

sigurnosti i zaštite zdravlja radnika te tehničkom nadgledanju

postrojenja, opreme, instalacija i uređaja u prostorima

ugroženim eksplozivnom atmosferom (NN br. 39/06,

106/07.), odnosno EU Direktivi 1999/92/EC (ATEX 137).

Odgovorna osoba dužna je osigurati njihovo provođenje u

pogonu.

This instruction is the basic information about the product. It is

complementing with the corresponding national laws and

regulations.

Production, use, certification and supervision are determined at the

national level:

a) Regulations concerning equipment and protective systems

intended for use in potentially explosive atmospheres EU

directive 94/9 EC (ATEX 94)

b) Regulations on minimum requirements for safety and health

protection of workers and technical inspection of facilities,

equipment, installations and equipment in hazardous areas EU

directive 1999/92/EC (ATEX 137).

The responsible person shall ensure their implementation at the

working facility.

10. SKLADIŠTENJE I TRANSPORT

10. STORAGE AND TRANSPORT

Transport i skladištenje treba vršiti samo u originalnoj ambalaži,

na način istaknut na kartonskoj kutiji.

Transportation and storage of the lamps is only allowed in the

original packaging, as outlined in a cardboard box.

11. JAMSTVO PROIZVOĐAČA

11. MANUFACTURER'S WARRANTY

Proizvođač daje jamstvo na proizvod u trajanju od godine dana

prema odredbama Zakona o obveznim odnosima. Ova izjava ima

snagu Jamstvenog lista.

The manufacturer provides a warranty on the product for a period

of one year under the provisions of this user manual and the law

on obligations. This statement has the force of Warranty sheet.

12. OZNAČAVANJE

12. MARKING

Protueksplozijski zaštićena ovjesna svjetiljka PLFSS LED-4

označena je s vanjskom označnom pločicom i unutarnjom

naljepnicom:

Explosion protected pendant light fitting PLFS 50 LED-4 is

marked with the external and the inner label with technical

data:

Natpisnom pločicom upozorenja na kućištu svjetiljke:

Warning label:

Natpisnom pločicom na poklopcu Ex e komore:

Marking label with the technical data (outside):

Natpisnom pločicom u Ex d kućištu s unutrašnje strane hladila:

Marking label with the technical data (inside):

Natpisnom pločicom upozorenja na vanjskoj strani Ex d kućišta

LED drivera:

Warning label on LED driver housing:

DO NOT OPEN WHEN AN

EXPLOSIVE ATMOSPHERE

IS PRESENT.

WARNING

II2D Ex tb op is IIIC T80°C Db IP66

PLFS 50 LED-4 EXA 18 ATEX . . . .

Croatia, Zagreb, Medarska 69

II2G Ex db eb op is IIC T6 Gb

WARNING - DO NOT OPEN WHEN ENERGIZED

0722

(1) (2)

Made in Croatia

-40°C < Tamb < +40°C P - KK -

90-305V 50/60Hz AC/127-431VDC 80 W

(1) (2)

II2D Ex tb op is IIIC T80°C Db IP66

PLFS 50 LED-4 EXA 18 ATEX . . . .

II2G Ex db eb op is IIC T6 Gb

(1) (2)

-40°C < Tamb < +40°C P - KK -

90-305V 50/60Hz AC/127-431VDC 80 W

Croatia, Zagreb, Medarska 69

Made in Croatia

0722

WARNING

DO NOT OPEN WHEN AN

EXPLOSIVE ATMOSPHERE

IS PRESENT.

DO NOT OPEN WHEN

ENERGIZED.

Table of contents

Other Tepex Light Fixture manuals

Tepex

Tepex PSF 28 LED-E User manual

Tepex

Tepex PSF 28 LED User manual

Tepex

Tepex PSF 218E User manual

Tepex

Tepex PLFS-N 100 LED User manual

Tepex

Tepex FLX 310 LED User manual

Popular Light Fixture manuals by other brands

Emos

Emos CLASSIC ZY1431T manual

Westinghouse

Westinghouse Outdoor Lighting Fixture owner's manual

Hedler

Hedler C 12 silent Operation manual

Blizzard Lighting

Blizzard Lighting Puck: CSI manual 

Energetic Lighting

Energetic Lighting ELYSL-5004 Series installation instructions

Lightmaxx

Lightmaxx Shaft 5R user manual

Triarch

Triarch 31083 Assembly instructions

Philips

Philips 32614 Series user manual

IKEA

IKEA TIVED Assembly instructions

Lightolier

Lightolier LP200 specification

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH user manual

Martin

Martin MAC 250 Krypton user manual

Cooper Lighting

Cooper Lighting Halo L3232E Specification sheet

Stageline

Stageline ODW-2410RGBW instruction manual

Light Sky

Light Sky Tornado Series user manual

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U specification

Lightolier

Lightolier Lytespan 83ED17S specification

Lightolier

Lightolier Calculite CS8226 specification