Teltonika RUT955 User manual

USER MANUAL

RUT955 LTE Router

USER MANUAL

RUT955 LTE ROUTER

Legal notice

of part or all of the contents in this document in any form without the prior written permission of

TELTONIKA Ltd is prohibited. The manufacturer reserves the right to modify the product and manual

for the purpose of technical improvement without prior notice.

Other product and company names mentioned herein may be trademarks or trade names of

their respective owners.

Attention

Before using the device we strongly recommend reading this user manual first.

Do not rip open the device. Do not touch the device if the device block is broken.

All wireless devices for data transferring may be susceptible to interference,

which could affect performance.

The device is not water-resistant. Keep it dry.

Device is powered by low voltage +9V DC power adapter.

Safety information

The RUT955 router must be used in compliance with any and all applicable national and international

laws and with any special restrictions regulating the utilization of the communication module in

prescribed applications and environments.

You have to be familiar with the safety requirements before using the device!

Specifications

Software

RUT955_R_XX.XX.XXX

Frequency bands*

EEE802,11b/g/n 2400 MHz, GSM/3G/4G, UMTS/HSPA+

Max. RF power

20 dBm@WiFi, 33 dBm@GSM/GPRS/EDGE, 24 dBm@LTE/WCDMA

Representative accessories specifications

Power

AC/DC power adapter 9 V 1 A, 2 pin plug

GSM/WCDMA/LTE antenna

703-960/1710-1990/2110-2170/2500-       gain** 1

dBi, omnidirectional, SMA male connector

WiFi antenna

2400-          -SMA

male connector

GPS antenna

1561-1615 Mhz, DC 3.3 V, VSWR , active total gain** 18 dBi (typ.), linear

polarization, SMA male connector

* Supported frequency bands are dependent on geographical location and may not be available in all markets.

** If an extension cable is used to attach the antenna, the antenna gain may be higher by the amount of cable

attenuation. The user is responsible for the compliance with the legal regulations.

To avoid burning and voltage caused traumas, of the personnel working with the device, please

follow these safety requirements:

The device is intended for supply from a Limited Power Source (LPS) that power

consumption should not exceed 15VA and current rating of over current protective

device should not exceed 2A.

The highest transient over voltage in the output (secondary circuit) of used PSU shall

not exceed 36V peak.

The device can be used with the Personal Computer (first safety class) or Notebook

(second safety class). Associated equipment: PSU (power supply unit) (LPS) and

personal computer (PC) shall comply with the requirements of standard EN 60950-1.

Do not mount or service the device during a thunderstorm.

To avoid mechanical damages to the device it is recommended to transport it packed

in a damage-proof pack.

Protection in primary circuits of associated PC and PSU (LPS) against short circuits

and earth faults of associated PC shall be provided as part of the building

installation.

To avoid mechanical damage to the device it is recommended to transport it packed in a damage-

proof pack. When using the device it should be placed so that its indicating LEDs would be visible as

they inform in which working mode the device is in and if it has any working problems.

Protection against over current, short circuiting and earth faults should be provided as a part of the

building installation.

Signal level of the device depends on the environment in which it is working in. In case the device

starts working insufficiently, please refer to qualified personnel in order to repair this product. We

recommend forwarding it to a repair center or the manufacturer. There are no exchangeable parts

inside the device.

Introduction

Thank you for purchasing a RUT955 LTE router! RUT955 is part of the RUT9xx series of compact

mobile routers with high speed wireless and Ethernet connections.



cumbersome cable connection. Unrestricted, but not forgotten: the router still supports internet

distribution via a broadband cable, simply plug it in to the wan port, set the router to a correct mode

and you are ready to browse.

For in-depth information on how to use and configure a RUT955 router, visit our wiki page:

http://wiki.teltonika.lt/index.php?title=RUT955

Hardware installation

1. Remove the back panel and insert your SIM cards. Correct SIM card orientation is shown in the

picture below:

2. Attach LTE, WiFi and GPS antennas.

3. Connect the power adapter to the socket on the front of the device. Then plug the other end of

the power adapter into a power socket.

4. Connect to the device wirelessly (SSID: Teltonika_Router) or use an Ethernet cable and plug it

into any LAN Ethernet port.

Front and back panels

Front view

1. LAN Ethernet ports

2. WAN Ethernet port

3. LAN LEDs

4. WAN LED

5. RS485

6. Power socket

7. RS232 interface

8. Input/output connector

9. Power LED

Mobile connection status LED

Mobile signal strength indication LEDs

Back view

1. LTE antenna connectors

2. GPS antenna connectors

3. USB connector

4. WiFi antenna connectors

5. Reset button

Configure your computer (Windows)

1. Enable the wireless network connection (go to Start >

Control Panel > Network and Internet > Network and

Sharing Center. In the left panel click Change adapter

settings link. Right click on Wireless Network

Connection and select Enable).

2. Setup the wireless network adapter on your computer

(right click on Wireless Network Connection and select

Properties). After that select Internet Protocol Version

4 (TCP/IP) and click Properties).

3. Select Obtain IP address automatically and Obtain

DNS server address automatically if they are not

selected. Click OK.

4. Right click on Wireless Network Connection

and click Connect to see available wireless

networks.

5. Choose the wireless network Teltonika_Router

from the list and click Connect.

1. To enter the routers Web interface type http://192.168.1.1 into your internet browser

2. Use the following parameters when prompted for authentication:

3. Configuration Wizard will start after logging in. It is necessary to complete Configuration Wizard

to setup the router to the correct mode. You can leave default settings but it is strongly

recommended that you change the default password and enable Wireless Security.

4. Go to Status > Network information and pay attention to Signal Strength. To maximize the

performance try adjusting the antennas or changing the location of your device to achieve the

best signal conditions.

LED indications

Constant blinking (~ 2Hz) router is turning on

LED turned off no 4G data connection

LED turned on 4G data connection

Connection status LED indication

Green and red blinking alternatively ever 500 ms: no SIM or bad PIN

Green, red and yellow blinking alternatively every 500 ms: connecting to GSM

Red blinking every 1 sec: connected 2G, but no data session established

Yellow blinking every 1 sec: connected 3G, no data session established

Green blinking every 1 sec: connected 4G, no data session established

Red lit and blinking rapidly while data is being transferred: connected 2G with data session

Yellow lit and blinking rapidly while data is being transferred: connected 3G with data session

Green lit and blinking rapidly while data is being transferred: connected 4G with data session

Signal strength LEDs

No. of lit up LEDs

Signal strength value

-111 dBm

-110 dBm to -97 dBm

2 -96 dBm to -82 dBm

-96 dBm to -82 dBm

-81 dBm to -67 dBm

-66 dBm to -52 dBm

-51 dBm

Specifications

Ethernet

IEEE 802.3, IEEE 802.3u standards

3 x LAN 10/100Mbps Ethernet ports

1 x WAN 10/100Mbps Ethernet port

Supports Auto MDI/MDIX

Wi-Fi

IEEE 802.11b/g/n WiFi standards

2x2 MIMO

AP and STA modes

64/128-bit WEP, WPA, WPA2, WPA&WPA2, EAP-PEAP encryption methods

2.401 –2.483 GHz WiFi frequency range*

20dBm max WiFi TX power

SSID stealth mode and access control based on MAC address

Hardware

High performance 560 MHz CPU with 128 Mbytes of DDR2 memory

2 pin industrial DC power socket

Attachable DIN rail adapter

4 pin industrial socket 2/4 wire RS485

DB9 socket for full-featured RS232

USB socket for external devices

Reset/restore to default button

2 x SMA for LTE, 2 x RP-SMA for WiFi antenna connectors

1 x SMA for GPS antenna connector

4 x Ethernet LEDs, 1 x power LED

1 x bi-color connection status LED, 5 x connection signal strength LEDs

10 pin industrial socket for inputs/outputs:

-0 –3 V digital input

-0 –30 V digital galvanically isolated input

-0 –24 V analog input; 30 V, 250 mA digital open collector output

-30 V, 250 mA digital open collector output

-40 V, 4 A SPST relay output

Electrical, Mechanical & Environmental

Dimensions (H x W x D) 80mm x 106mm x 46mm

Weight 265g

Power supply 100 –240 VAC -> 9 VDC wall adapter

Input voltage range 9 –30VDC

Power consumption < 7W

Operating temperature -40°to 75°C

Storage temperature -45°to 80°C

Operating humidity 10% to 90% Non-condensing

Storage humidity 5% to 95% Non-condensing

*Supported frequency bands are dependent on geographical location and may not be available in all markets

Other manuals for RUT955

Table of contents

Other Teltonika Network Router manuals

Teltonika

Teltonika RUT230 User manual

Teltonika

Teltonika RUT500 User manual

Teltonika

Teltonika RUT955 User manual

Teltonika

Teltonika QSG RUT241 User manual

Teltonika

Teltonika QSG RUT240 User manual

Teltonika

Teltonika WiMAX User manual

Teltonika

Teltonika TRB145 User manual

Teltonika

Teltonika TMT250 Installation and user guide

Teltonika

Teltonika RUT951 User manual

Teltonika

Teltonika RUT240 User manual

Teltonika

Teltonika TMT250 User manual

Teltonika

Teltonika QSG RUT955 User manual

Teltonika

Teltonika RUT950 User manual

Teltonika

Teltonika RUT905 User manual

Teltonika

Teltonika RUTX08 User manual

Teltonika

Teltonika RUT360 User manual

Teltonika

Teltonika RUT230 User manual

Teltonika

Teltonika RUT200 User manual

Teltonika

Teltonika RUT240 User manual

Teltonika

Teltonika RUT850 User manual

Teltonika

Teltonika RUT500 User manual

Teltonika

Teltonika QSG RUT951 User manual

Teltonika

Teltonika RUT950 User manual

Teltonika

Teltonika RUT956 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview