Teltonika TMT250 User manual

Saltoniškių g. 9B-1,

LT-08105 Vilnius

Tel. +370 5 212 7472

Faks. +370 5 276 1380

www.teltonika-iot-group.com

[email protected]

TMT250 First Start

From Wiki Knowledge Base | Teltonika Mobility

Main Page > Personal Trackers > TMT250 > TMT250 First Start

Contents

1 How to insert micro SIM card and connect the battery to TMT250

1.1 Correct Battery Connection

1.2 PC Connection (Windows)

1.3 How to install USB drivers (Windows)

1.4 Conguration (Windows)

1.5 Quick SMS conguration

1.6 Precautions

How to insert micro SIM card and connect the battery to TMT250

1. Unscrew 4 screws counterclockwise.

2. Remove the cover.

3. Insert Micro-SIM card as shown. Make sure that Micro-SIM card cut-o corner is pointing forward to slot.

4. Connect the battery as shown to the device.

5. Attach device cover back and screw in all 4 screws.

6. Device is ready to be used.

Saltoniškių g. 9B-1,

LT-08105 Vilnius

Tel. +370 5 212 7472

Faks. +370 5 276 1380

www.teltonika-iot-group.com

[email protected]

NOTE: In order to prevent device's cover from mechanical damage it is recommended to use screwdriver, which is included in the package.

Correct Battery Connection

Saltoniškių g. 9B-1,

LT-08105 Vilnius

Tel. +370 5 212 7472

Faks. +370 5 276 1380

www.teltonika-iot-group.com

[email protected]

PC Connection (Windows)

1. Connect device to computer using Magnetic USB cable or Bluetooth connection:

Using Magnetic USB cable

You will need to install USB drivers, see "How to install USB drivers (Windows)"

Using Bluetooth

TMT250 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth.

Choose your device named – “TMT250_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect

and then select Done.

2. You are now ready to use the device on your computer.

Saltoniškių g. 9B-1,

LT-08105 Vilnius

Tel. +370 5 212 7472

Faks. +370 5 276 1380

www.teltonika-iot-group.com

[email protected]

How to install USB drivers (Windows)

1. Please download COM port drivers from Teltonika here (https://teltonika-gps.com/downloads/en/fmb120/TeltonikaCOMDriver.zip).

2. Extract and run TeltonikaCOMDriver.exe.

3. Click Next in driver installation window.

4. In the following window click Install button.

5. Setup will continue installing the driver and eventually the conrmation window will appear. Click Finish to complete the setup.

Conguration (Windows)

At rst TMT250 device will have default factory settings set. These settings should be changed according to the user's needs.

Main conguration can be performed via Teltonika Congurator software. Get the latest TMT250 Congurator version from here. Congurator

operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

MS .NET requirements

Operating system MS .NET Framework

version Version Link

Windows

Vista

Windows 7

Windows

8.1

Windows 10

MS .NET Framework 4.6.2 32 and 64

bit

www.microsoft.com

(https://dotnet.micro

soft.com/en-us/down

load/dotnet-framewo

rk)

Downloaded Congurator will be in compressed archive. Extract it and launch Congurator.exe. After launch software language can be changed

by clicking in the right bottom corner:

Saltoniškių g. 9B-1,

LT-08105 Vilnius

Tel. +370 5 212 7472

Faks. +370 5 276 1380

www.teltonika-iot-group.com

[email protected]

Conguration process begins by pressing on connected device:

After connection to Congurator Status window will be displayed:

Saltoniškių g. 9B-1,

LT-08105 Vilnius

Tel. +370 5 212 7472

Faks. +370 5 276 1380

www.teltonika-iot-group.com

[email protected]

Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc. TMT250 has one user editable prole, which can

be loaded and saved to the device. After any modication of conguration the changes need to be saved to device using Save to device button.

Main buttons oer following functionality:

1. Load from device – loads conguration from device.

2. Save to device – saves conguration to device.

3. Load from le – loads conguration from le.

4. Save to le – saves conguration to le.

5. Update rmware – updates rmware on device.

6. Read records – read records from device.

7. Reboot device – restarts device.

8. Reset conguration – sets device conguration to default.

Saltoniškių g. 9B-1,

LT-08105 Vilnius

Tel. +370 5 212 7472

Faks. +370 5 276 1380

www.teltonika-iot-group.com

[email protected]

Most important congurator section is GPRS – where all your server and GPRS settings can be congured and Data Acquisition – where data

acquiring parameters can be congured. More details about TMT250 conguration using Congurator can be found here.

Quick SMS conguration

Default conguration has optimal parameters present to ensure best performance of track quality and data usage.

Quickly set up your device by sending this SMS command to it:

" setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0"

Note: Before SMS text, two space symbols should be inserted.

Default conguration settings

Movement detection:

Movement will be detected by

accelerometer

Device makes a record On Moving if one of these events happen:

300 seconds passes Angle dierence between last coordinate

and current position is greater than 10°

GPRS settings:

2001 – APN

2002 – APN username (if there are no APN username, empty eld

should be left)

2003 – APN password (if there are no APN password, empty eld

should be left)

Server settings:

2004 – Domain

2005 – Port

2006 – Data sending protocol (0 – TCP, 1 – UDP)

Saltoniškių g. 9B-1,

LT-08105 Vilnius

Tel. +370 5 212 7472

Faks. +370 5 276 1380

www.teltonika-iot-group.com

[email protected]

degrees

Traveled distance is more than 100

meters

Speed dierence between last coordinate

and current position is greater than 10

km/h

Device makes a record On Stop if:

1 hour passes while device is

stationary

Records sending to server:

If device has made a record it is sent

to the server every 120 seconds

After successful SMS conguration, TMT250 device will synchronize time and update records to congured

server. Time intervals and default I/O elements can be changed by using Teltonika Congurator or SMS

parameters.

Precautions

Saltoniškių g. 9B-1,

LT-08105 Vilnius

Tel. +370 5 212 7472

Faks. +370 5 276 1380

www.teltonika-iot-group.com

[email protected]

Operate the device in suitable conditions

Do not use the device where mobile connectivity is forbidden.

Road safety rst

Comply with local trac laws, always hold your hands on a steering wheel when using a device. Your safety is of utmost importance when you drive.

Interference

All wireless devices are sensitive to electromagnetic interference, as a result wireless devices aect the performance of each other.

Limit the use of device in hospitals

Please follow all restrictions. Turn o the device in the vicinity of medical devices when required.

Limit the use of device in vehicles

Please follow all restrictions. Wireless devices can interfere with other electronic equipment in vehicles.

Be cautious near ammable materials and liquids

Charging precautions

SELV LPS chargers, personal computers or laptops that device will be connected to must comply with the requirements of IEC 60950:2005 standard.

Use only original batteries

Using uncertied manufacturer or dierent type batteries may cause an explosion.

Use batteries safely

Protect batteries from moisture. Place them in a cool and dry place when storing. Avoid extensive operation at high temperatures. Do not attempt charging battery

directly from the electrical mains. All utilised batteries shall comply with IEC 62133.

Saltoniškių g. 9B-1,

LT-08105 Vilnius

Tel. +370 5 212 7472

Faks. +370 5 276 1380

www.teltonika-iot-group.com

[email protected]

Power supplies

Power supply circuits used to charge the device connection must have safeguards, which prevent power leakage, short circuits or incorrect electrical grounding. Any

used switches ought to be installed in a readily accessible location. Power must be uninterrupted and the distance between the contacts must be 3 mm or larger.

Remove device safely

Device must be disconnected from computer or charger by unplugging the magnetic USB cable from the device.

Other

In order to prevent device from mechanical damage it is advisable to transport it in a shock–resistant packaging. If device stopped working properly regardless of the

settings only a qualied specialist can help. It is recommended to contact your local seller or your UAB Teltonika manager in such a case.

Use the right screwdriver

In order to prevent device's cover from mechanical damage it is recommended to use screwdriver, which is included in the package. Do not use electrical screwdrivers.