Teko Astra-7 ver.A User manual

Popular Security Sensor manuals by other brands

THORLABS

THORLABS PDA10JT user guide

Waeco

Waeco UV-DETECT operating manual

Intermatic

Intermatic IOS-DSIMF manual

urmet domus

urmet domus 1083 manual

Siemens

Siemens AZL66 Series manual

BTI

BTI Profiline Multi Finder operating instructions

Challenger

Challenger SL01 instruction manual

DMP Electronics

DMP Electronics 1122INT installation guide

Rielta

Rielta Ladoga MK-RK installation guide

Mirion Technologies

Mirion Technologies ACCURAD PRD user manual

Bosch

Bosch DS835 installation instructions

DBI SALA

DBI SALA EZ Stop User instruction manual

Lamptime

Lamptime ST05C instructions

Ubiquiti

Ubiquiti MFI-MSC quick start guide

Subsite

Subsite 910R Support

Satel

Satel OPAL Pro manual

Aleph

Aleph XC-1XTEU manual

Pima

Pima LARIS QUAD installation instructions

Astra-7 ver.A

(Volumetric Lens)

Optic-Electronic PIR Motion

Detector

User Guide

Manufacturer:

ZAO NTC TEKO

420108 Kazan, Russia

Gafuri 71

+7 843 528-03-69

[email protected]

www.teko.biz

Made in Russia

Rev. 7-av1_5_instr_en

1 FUNCTION

Detector is intended to detect unauthorized

access into closed protected area and generate

an alarm notification by opening relay contacts.

2 DETECTION ZONE

3 SPECIFICATION

Range of detectable

moving speed, m/sec.............from 0.3 up to 3.0

Power supply voltage, V.............from 8 up to 15

Current consumption, mA, max......................15

Overall dimensions, mm..................diameter 91

height 31

Operating Conditions

Temperature range, °С........ from - 30 up to +50

Relative air humidity, % .......... up to 98 at +25 °С

Withoutmoisture condensation

4 DELIVERY SET

Delivery set includes: dowel –2 pcs., screw –2

pcs., user guide –1 pcs., label –2 pcs.

5 MODES OF OPERATION

Plug

Jumper

position

High detectability

Normal

detectability

Mode

Indication ON

Indication OFF

Ind

“Alarm memory”

ON

“Alarm memory”

OFF

Mem

TEST-pass

Ind

See sec. 9

6 INSTALLATION PLACE

1) Recommended installation height is 2.4-3.6 m.

2) Detector should be installed on the ceiling

(or any other horizontal surface) horizontally.

3) Alarm loop and power supply wires should

be located far from power cables.

To eliminate false alarm hazards

It is recommended to close all doors, air-vents,

switch off fans, air-conditioners and other

sources of intense air flows in the room during

protection period.

Not recommended installation places

7 INSTALLATION PROCEDURE

1) Remove

cover

2) Remove

PCB

3) Install base

on the

ceiling

4) Install PCB

and perform

wiring (see

sec.8)

5) Perform TEST-pass (see sec.9)

8 WIRING

Perform wiring to detector`s terminals in

accordance with control panel operating manual.

TMP –detector tampering control terminals;

RELAY –terminals for detector connection to

alarm loop;

+12V, GND –power supply terminals.

9 TEST-PASS

1) Remove jumper from Mem plug, install

jumpers on Ind and Mode plugs.

2) Power detector ON. LED starts flash during

60 sec.

3) During this time

4) Close detector.

5) To detect sensitive

zones carry out

TEST-pass in the

secured zone with the

speed of 0,3 m/sec.

On detection

(indicator is lighted

for 2sec) one should

stop, mark this

position, then make

step back and continue moving.

Repeat TEST-pass inversely.

10 WARRANTY

The operation warranty period is 5 years from

the date of operation start-up but no longer than

5 years 6 months from the date of manufactur-

ing subject to the requirements of Operating

Manual.