Team Nisca Nisca PR5300 User manual
DIRECT CARD PRINTER
PR5300
Operation Manual
Ver. 1.3
Aug.'00
Contents
: For your sa etySection 1
a) Before installing
b) Before turning power ON
c) Before using
d) Before moving the equipment
e) About laws and regulations
F) Prohibited matters
: Preparation
Section 2
a) Pac age csntents
b) Consumables
c) Parts tobereplacedperiodically
d) Name of theparts
: Installation
Section 3
a) Environment for installation
b) Space for installation
c) Prepation for installation
d) Connecting the Printer to Computer
e) owerONP
f)Settingsafter the owerON
P
: Operation Panel
Section 4
a) Outline of the Operation Panel
b) Operation of Normal Mode
c) OperationofUserMode
d) Function of User Mode
e) StructureofUserMode
: Operation
Section 5
a) Setting cards
b) Setting the in ribbon
: Cleaning
Section 6
a) Input Roller
b) Cleaningofthecardtransportrollersin Flip Turn Bloc
c) Cleaning of theprintrollers
d) Cleaningoftheribbontransport roller
e) Cleaning of the Suply roller
f)Cleaning of the Print Head
: Periodical replacement o parts
Section 7
a) Replacing Input Roller
b) Replacing Print Head
: Basic speci ication
Section 8
: Con iguration o the equipmentSection 9
: TroubleandcountermeasureSection 10
-1-
Section 1: For your sa ety
Several illustrations are used in this operation manual to ensure safe
operation. The following conventions are used to identify the result caused
by the use or operations not following such illustrations.
:This indicates that there is a danger of death or
serious injury.
:This indicates that there is possibility of death or
serious injury.
:This indicates that there is a possible cause of injury
and/or damages on properties.
This manual MUST be read fully before operating the printer.
2 Page
a) Special attention
2 Pageb) Be ore installing
4 Pagec) Be ore turning the power ON
6 Paged) Be ore using
9 Pagee) Be ore moving
9 Page) Other
Meaning o the marks
" Be care ul "¢means
" Never do this "
means
" Must do this "
means
-2-
1- Be ore installing
a)
About environment or installation
Do not install in humid and dusty room.It may
cause fire and/or electric shock.
Do not install the equipments near the
heat emitting apparatus such as stove
and heater or near the flammables such
as curtain. It may cause fire.
Do not place on shaky table or inclined
location. It may fall or drop and cause
injury to nearby persons.
-3-
Do not place where there is direct sunlight.
It may cause deformation ofplastic housing
and decoloration of the prints.
Enough space must be provided around the
equipments. This is necessary for easy
operation as well as for ventilation.
If the ventilation opening is closed by
obstcle, heat can not be dissipated and
it may cause a fire.
( Place with the clearance as shown in
the illustration. )
Do not place in the room with much
vibration. It may cause troubles on the
equipments.
Do not place in such place where the
temperature changes rapidly. If the
cold room is suddenly heated it may
cause condensation on the equipments
and damage the print quality or even
printing function itself.
6inch
15cm
6inch
15cm 6inch
15cm
12inch
30cm
-4-
1- Be ore turning the power ON
b)
About power source
Do not use any other outlet than followig.
Do not connect more than one equipments
onto one outlet. Otherwise, it may cause
a fire and/or electric shock.The specified
rating of this equipment is following.
100 ‘240 VAC 2A
Dust on the plug and electrical outlet mustbe removed.If used without
removing, a small amount of electricity runs continuously through the dust
by the effect of moisture etc. and may eventually cause a fire.
Be careful so that the power supply cord
is not damaged. If the cord is twisted,
pulled strongly or placed underneath a
heavy object, it may be damaged and become
a cause of fire.
Do not handle the plug with wet hand
because it may cause electric shock.
When you use an extention cord, do not use the cord which is rated at less
than 125V 10A. Excessive heat or smoke will be caused.
-5-
About connecting the grounding line
Grounding line must be connected. If the
equipment is not grounded and there is
an electric leakage, it may cause electric
shock or fire.
qGrounding line may be connected to the following points. r
Grounding terminal on the electric outlet
The line connected to an copper rod which is buried in the ground at the
depth of 65cm(26inch) or deeper.
qGrounding line may not be connected to the following points. r
Gas pipe ( There is a danger of fire and/or explosion. )
Water faucet or pipe ( It does not lead to the ground as plastic pipe
may be used. However, it can be connected if it is marked as possible
grounding facility.)
Grounding line of telephone or lightning rod ( It is dangerous as large
electric current will run when hit by lightning. )
-6-
1- Be ore using
c)
About handling the equipment
Do not put anything containing water such
as vase etc. on the equipment. If water is
spilled, it may cause fire or electric
shock.
Do not put any metal pieces such as paper
clips on the equipment. If they drop inside
the equipment, it may cause short circuit
and cause fire or electric shock.
If, by any chance, metal pieces or water get inside the equipment, turn off
the main switch and plug off the power supply cord from the outlet. Then,
contact the dealer from whom you have purchsed the equipment. Using as it
is may cause fire or electric shock.
Do not open the panel or cover which is fixed with screws, other than
directed by the manual. There is live part carrying high voltage and it is
dangerous of electric shock.
Do not modify the equipment. It may cause the danger of fire or electric
shock.
-7-
If smoke or unusual smell is detected, stop
using. If it is used as it is,it may cause
fire or electric shock. Turn OFF the main
switch immediately,plug off the power cord
and contact the dealer from whom the
equipment was purchased.
In case of thunder, for the purpose of safety, turn OFF the main switch and
plug off the power cord. This will prevent burning of the equipment, fire
or electric shock.
If the equipment will not be used for a long period, turn OFF the main
switch and plug off the power cord for safety. Deterioration of insulation
may cause electric shock or leakage and fire.
-8-
About handling o the equipment
Do not put any heavy article on the equipment. It may damage the equipment
or cause the injury by dropping.
Do not use flammable sprays at near the equipment. It may catch fire and
cause fire accident.
When the front door is open, do not put anything on the door or lean on.
The door may be broken and will cause injury.
While the equipment is in operation, do not turn OFF the main switch, pull
off the plug of power cord or open the doors of the equipment.
It may cause card jamming or malfunction of the equipment.
Do not touch any part inside the equipment other than directed by this
manual.
Read this manual carefully before performing recovering operations for
card jamming or other malfunctions.
Do not attempt to operate in any other way than designated in this manual.
Such attempt may cause unexpected damage on the equipment.
If electric leakage occurs frequently, please contact the dealer from whom
you have purchased the equipment.
Cooling fans are rotating continuously to prevent temperature rise inside
the equipment. This is not a defect. Do not put anything which may prevent
air flow near the ventilation opening of the equipment.
Other manuals for Nisca PR5300
1
Table of contents
Other Team Nisca Printer manuals
