TBK TBK-2900D User manual
Dual CCD Box Camera
Instruction Manual
TBK-2900D
Dual CCD Box Camera
2
Warnings & Caution ------------------------------------------------------------------------- 3
What’s in the Box? ----------------------------------------------------------------------------3
General Features ------------------------------------------------------------------------------4
Name of Each Part --------------------------------------------------------------------------- 5
Installation ---------------------------------------------------------------------------------------7
Connection-------------------------------------------------------------------------------------- 9
Specifications ---------------------------------------------------------------------------------10
OSD Menu Setting----------------------------------------------------------------------------11
Dimensions ----------------------------------------------------------------------------------- 19
Troubleshooting ----------------------------------------------------------------------------- 20
CONTENTS
3
WARNINGS & CAUTION
If you fail to read this information and
handle the product incorrectly, death or
serious injury may occur.
1. Camera (TBK-2900D)
2. C Mount Ring
3. IRIS Lens Jack
4. Manual
5. Wrench 0.89mm
The unit should be installed by the
trained personnel.
Switch off immediately if the product
emits smoke or abnormal heat.
Never install the product in area
exposed to oil or gas.
Never touch the power cord with wet
hands.
Clean only with dry cloth.
Ensure that the product is not
subjected to strong impacts and
vibration.
Never expose the camera to direct
sunlight
Never disassemble the unit by
unauthorized person. Serious and
Permanent damage will occur.
Warning
This symbol is intended to alert
the user to the presence of un-
insulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to
p
ersons.
This symbol is intended to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
What’s in the Box?
4
GENERAL FEATURES
Built-in Dual CCD
Operating with two CCDs: Super HAD
CCD Color for daytime and B/W Ex-View
CCD for nighttime.
Exchanging according to light condition.
Detecting a motion or shape in a very
dark place.
Reducing the recording data capacity
more than 40% than ICR type (Sony
Supper HAD CCD)
Providing better compressibility times
than ICR type.
Providing best illumination every corner
of the screen.
Polarity Protection of Power
Preventing damage to the power board
of Domes when the DC supply is
connected to an inaccurate polarity
Multiple Languages.
Supplying with total 4 languages,
English, Japanese, Korean, Chinese
(Simplified Chinese, Traditional Chinese).
Privacy Masking Zone
You can easily set up privacy masking
areas to be masked unwanted zones
and hide them from display on the
screen.
Built-in Motion Detection
Detecting any motion or shape on the
Screen.
5
A. This Camera is equipped with CDS Sensor that makes Day & Night function executed
accurately in the infrared area and both C and CS Mount Lens are adoptable.
1. CDS Sensor
2. Cs Mount Adaptor
3. Camera Body
4. Auto IRIS
5. Fastening Bracket groove
(bottom)
NAME OF EACH PART
①
②
⑤
③
④
FIG.1
6
A. Name of Rear Part
1. Menu/Set Control Button
2. Video Output(CVBS) -
3. Power LED
4. Lux Control (10 steps)
5. UTP Video Output (UTP+/-)
6. GND
7. Power Input ( AC24V / DC 12V )
③
① ②
④
⑤⑥⑦
FIG.２
NAME OF EACH PART
7
A. Auto Iris Lens (Only DC LENS applicable)
1. Peel off the outer cover ofAuto Iris Lens cable about 8mm from the end
2. Peel off the inner cover ofAuto Iris Lens cable about 2mm from the end.
3. Take off the cover of Lens Joint-Plug and insert the Lens Cable into the pin of Auto Iris
Connector and solder it.
4. Turn Auto Iris Lens to counterclockwise direction and connect it up.
5. Connect Auto Iris Lens jack to the Camera body.
`
INSTALLATION
FIG.３
8
B. AUTO IRIS Pin Formation
1.CONTROL-
2.CONTROL+
3.DRIVE+
4.DRIVE-
C. Fastening Bracket groove
Set Bolt for Bracket is 1 / 4 - 20 UNC .
FIG.５
AUTO IRIS Lens Connector
AUTO IRIS Connector (Camera body)
FIG.４
INSTALLATION
9
L: 4.5mm ± 0.2mm (ISO Standard).
A. CONNECTING TO MONITOR BY UTP CABLE
1. Connect the Video terminal division on the back of the camera with image input division of a
Monitor.
2. You can use DC12V or AC24V in accordance with standardized power type. Please make sure if
you use a right type of an adaptor and that you should connect the power after completed all
installation.
CONNECTION
UTP Receiver
Adaptor
AC24V/DC12V
10
TBK-2900D
Type BUILT-IN DUAL CCD
Image Device Sony - 1/3” SUPER HAD Color CCD
1/3” B/W Ex-view CCD for night
Effective Pixels NTSC : 768 (H) x 494 (V)
PAL : 752 (H) x 582 (V)
Resolution More than 600 TV Lines for B/W
More than 540 TV Lines for color
Video System NTSC,PAL TV System
Scanning
System NTSC : 525 Lines 2:1 Interlace
PAL : 625 Lines 2:1 Interlace
Scanning
Frequency NTSC : 15.734 [KHZ] / 59.94 [HZ]
PAL : 15.625 [KHZ] / 50 [HZ]
Shutter speed NTSC:1/60~1/100,000sec PAL:1/50~100,000sec
Sync System Internal sync
LENS ALC(DC auto iris lens control)
BLC ON/OFF, controllable function to details (Area, Ratio, ETC…)
FLK ON/OFF
White Balance AWB/ATW/Manual/Fixed
Gamma User Setting 0.1~1.0, (Default r=0.45)
S/N Ratio More than 48 [dB] / AGC off
C.Video Output CVBS 1.1 Vp-p / 75 ohm :
Minimum
Illumination 0.003 Lux (F:1.2/40IRE)
Operation Power Dual Power (DC 12V, AC24V)
Power
Consumption (DC12V 500mA / AC24V 400mA 10W(MAX))
Operating Temp. -10℃~+50
SPECIFICATIONS
Table of contents
Other TBK Security Camera manuals
