Supermicro X13SRA-TF User manual
X13SRA-TF
ENGLISH
繁體中文
简体中文
日本語
한국어
QUICK REFERENCE GUIDE
Revision 1.00
Standardized Warning Statements
Motherboards
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of situations where bodily injury
might occur. Should you have questions or experience diculty, contact Supermicro's Technical Support Department
for assistance. Only certied technicians should attempt to install or congure components.
Read this section in its entirety before installing or conguring components in the Supermicro chassis.
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-
lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理
廢棄舊電池。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理
废旧电池。
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメーカーが推奨する型、または同等のもの
を使用下さい。 使用済電池は製造元の指示に従って処分して下さい。
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한
종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Note: For complete product safety information, refer to https://www.supermicro.com/about/policies/safety_information.cfm.
X13SRA-TF QUICK REFERENCE GUIDE Product Safety Information
WARNING: This product can expose you to chemicals including
lead, known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information, go
to www.P65Warnings.ca.gov.
!
X13SRA-TF QUICK REFERENCE GUIDE 限用物質含有情況標示聲明書
限
限
用
用
物
物
質
質
含
含
有
有
情
情
況
況
標
標
示
示
聲
聲
明
明
書
書
設備名稱：主機板 /
Motherboard
型號（型式）：X13SRA-TF
單元Ｕnit
限用物質及其化學符號
鉛Lead
(Pb) 汞Mercury
(Hg) 鎘Cadmium
(Cd)
六價鉻
Hexavalent
chromium
(Cr+6)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
主機板
(Motherboard)
－○○○○○
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準
值。
備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考3.〝－〞係指該項限用物質為排除項目。
Equipment name
Type designation (Type)
Restricted substances and its chemical symbols
Declaration of the Presence Condition of the Restricted Substances Marking
Note 1
：
“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the
reference percentage value of presence condition.
Note 2
：
“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3
：
The “−” indicates that the restricted substance corresponds to the exemption.
AMI BIOS POST Codes
About AMI BIOS POST Codes
The table below lists some of AMI BIOS POST codes for this motherboard. For more information, refer to https://www.
supermicro.com/manuals/other/AMI_AptioV_BIOS_POST_Codes_for_SM_Motherboards.pdf.
Code Description
0x32 CPU post-memory initialization is started
0x55 No Memory detected or memory failed
0x63 CPU DXE initialization is started
0x69 North Bridge DXE initialization is started
0x70 South Bridge DXE initialization is started
0x92 PCI Bus initialization is started
0x99 Super IO Initialization
0x9A USB initialization is started
0xA0 IDE initialization is started
0xA9 Boot into BIOS setup menu
0xAE Legacy Boot event
0xB2 Legacy Option ROM Initialization
0xB4 USB hot plug
0xD6 No console output devices are found
0xD7 No console input devices are found
0xF2 Recovery process started
0xF9 Recovery capsule is not found
X13SRA-TF QUICK REFERENCE GUIDE BIOS POST Codes
M.2 Device Installation
M.2 Device Installation
X13SRA-TF QUICK REFERENCE GUIDE
Note 1: It is strongly recommended that you install a heatsink on the M.2 device or use a M.2 device
with a built-in heatsink.
Note 2: Be sure to install the M.2 device(s) prior to placing the motherboard into a chassis.
This motherboard has two M.2 M-key sockets that support the 2280 and 22110 M.2 devices.
One stando and a screw are pre-installed into the position of each 22110 mounting hole.
Refer to the illustration below for the locations of M.2 sockets and mounting holes. Follow
the steps on the next two pages to install the M.2 device.
SP1
X13SRA-TF
DESIGNED IN USA
REV:1.01
22110
2280
2280 M.2 Device Installation
X13SRA-TF QUICK REFERENCE GUIDE 2280 M.2 Device Installation
1. Locate the pre-installed standoff and
screw. Remove the screw and set it aside.
2. Using a hex socket screwdriver, remove
and then re-install the stando to the posi-
tion of the 2280 mounting hole.
3. Insert the M.2 device into the M.2 socket
at a 30-degree angle and press it down.
4. Tighten the screw to secure the M.2 device
into place. Do not overtighten so as to
avoid damaging the M.2 device.
22110 M.2 Device Installation
X13SRA-TF QUICK REFERENCE GUIDE 22110 M.2 Device Installation
1. Locate the pre-installed screw. Remove
the screw and set it aside.
2. Insert the M.2 device into the M.2 socket
at a 30-degree angle and press it down.
3. Tighten the screw to secure the M.2 device
into place. Do not overtighten so as to
avoid damaging the M.2 device.
Memory Population
Note: Unbalanced memory conguration decreases memory performance and is not recommended for Supermicro
motherboards.
Memory Population
X13SRA-TF QUICK REFERENCE GUIDE
Memory Population Table
DDR5 Memory Population Table
DDR5 DIMMF1 DIMMF2 DIMME1 DIMME2
CPU
DIMMA2 DIMMA1 DIMMB2 DIMMB1
1DDR5
DDR5
2DDR5 DDR5
4DDR5 DDR5 DDR5 DDR5
6DDR5 DDR5 DDR5 DDR5 DDR5 DDR5
DDR5 DDR5 DDR5 DDR5 DDR5 DDR5
8DDR5 DDR5 DDR5 DDR5 DDR5 DDR5 DDR5 DDR5
DDR5 Memory Support for the Intel Xeon W Processors
DDR5 Memory Support for the Intel Xeon W Processors
Type Ranks Per DIMM
& Data Width
DIMM Capacity (GB)
Speed (MT/s); Voltage (V);
DIMM Per Channel (DPC)
1DPC (Note) 2DPC
16GB 1.1V
RDIMM
SRx8 (RC D) 16GB
4800 4400
SRx4 (RC C) 32GB
DRx8 (RC E) 32GB
DRx4 (RC A) 64GB
RDIMM 3DS (4R/8R) x4 (RC A) 2H-128GB
4H-256GB
*1DPC applies to 1 SPC (Sockets Per Channel) or 2 SPC implementation.
X13SRA-TF
Quick RefeRence Guide Rev. 1.00
SUPERMICR R
Motherboard Layout and Features
BAR CODE
BAR CODE
IPMI CODE
MAC CODE
MAC CODE
SAS CODE
JTPM1
SP1
USB9 (3.2)
(USB3.2 GEN2X2)
UID-LED
JPI2C1
M.2-C01 LED
M.2-C02 LED
JF1
JWD1
JPL1
JPUSB1
JPL2
JSD1
FAN2
HD AUDIO
AUDIO FP
JUIDB1
LED8
COM1
USB0/1
FANB FANC
BATTERY
DIMME2
DIMMF2
DIMMF1
DIMME1
DIMMA2
DIMMA1
DIMMB2
DIMMB1
SATA1
SATA0 SATA3
SATA2 SATA4
SATA5
M.2-C01
M.2-C02
JPME2
JL1
JCMOS
JBT1
JPW2
JPW3
FAN1
FANA
JSTBY1
CPU SLOT6 PCIe 5.0 X16
JOH1
JPW1
12V_
PUMP_PWR1
USB8
(USB3.2 GEN2X2)
VGA
CPU SLOT4 PCIe 5.0 X16
PCH SLOT1 PCIe 4.0 X4
CPU SLOT2 PCIe 5.0 X16
BMC LED
JSPDIF_OUT
JPAC1
CPU
PCH
BIOS LICENSE
LAN
CTRL
BMC
USB6/7
(USB3.2 GEN2)
LAN1
USB4/5
(USB3.2 GEN2)
LAN2
Power LED
(PCIe 5.0 X4)
(PCIe 5.0 X4)
X13SRA-TF
DESIGNED IN USA
REV:1.01
JRK1
(RAID Key Header)
JD1
(SPEAKER 1-4)
USB2/3 (3.0)
(USB3.2 GEN1)
LAN
CTRL
BACK PANEL I/O
LGA 4677
=mounting hole
Other manuals for X13SRA-TF
1
Table of contents
Languages:
Other Supermicro Server manuals
Supermicro
Supermicro SuperServer SSG-640SP-DE2CR90 User manual
Supermicro
Supermicro SuperServer SYS-E200-12A-4C User manual
Supermicro
Supermicro SuperServer E300-12C User manual
Supermicro
Supermicro Supero SUPERSERVER 2027PR-HTR User manual
Supermicro
Supermicro SuperServer 1029P-NR32R User manual
Supermicro
Supermicro Supero SUPERSERVER 2027PR-DTR User manual
Supermicro
Supermicro SuperServer SYS-220U-TNR User manual
Supermicro
Supermicro A+ Server AS-2115GT-HNTR User manual
Supermicro
Supermicro 8042-6 User manual
Supermicro
Supermicro SuperServer 5019P-MT User manual
Supermicro
Supermicro SBI-7427R-S2L User manual
Supermicro
Supermicro SuperStorage SSG-610P-ACR12N4H User manual
Supermicro
Supermicro 1027R-73DAF User manual
Supermicro
Supermicro SuperServer 1019S-M2 User manual
Supermicro
Supermicro 7047R-72RF User manual
Supermicro
Supermicro SUPERSERVER 5018A-LTN4 User manual
Supermicro
Supermicro SuperServer SYS-820GH-TNR2 User manual
Supermicro
Supermicro SBI-7228R-T2F User manual
Supermicro
Supermicro SuperServer 1019C-HTN2 User manual
Supermicro
Supermicro SuperServer 5039MS-H8TRF User manual
