Sunricher SR-ZV9002T3-CCT-US User manual

Z-Wave Wall Controller SR-ZV9002T3-CCT-US

Safety & Warnings

•

• DO NOT expose the device to moisture.

Quick Start

How to install:

• Step 1: turn on your wall controller.

• Step 2: activate inclusion mode on your Z-Wave controller.

• Step 3: activate inclusion mode of your wall controller by pressing the

“inclusion/exclusion” button or long press “ALL ON/OFF” button over 3 seconds.

Product Description

The Wall controller is a Security Enabled Z-Wave Plus device that can both control other

Z-Wave devices and activate scenes in Gateways. The wall controller can be included

and operated in any Z-Wave network with other Z-Wave certified devices from other

manufacturers and/or other applications. All non‐battery operated nodes within the

network will act as repeaters regardless of vendor to increase reliability of the network.

Although it is controlling other devices, the device cannot act as Z-Wave network

controller (primary or secondary), so a security enabled controller is needed for take full

advantage of all functionally for the device. It also supports the Over The Air (OTA)

feature for the product’s firmware upgrade.

The wall controller has following functions:

1.Control of groups of other Z-Wave devices using 'ON', 'OFF', Dim and Color Control

commands.

2. Activation of scenes in Gateways.

The encryption modes that the wall controller supports are S0, S2 Unauthenticated.

When the wall controller is being included into a Z-Wave network, you can use your

primary controller/gateway to enable one encryption mode or disable encryption. (The

primary controller/gateway shall support encryption mode configuration).

DO NOT install with power applied to device.

Product Data

Z-Wave Frequency

Power Supply

Power Consumption

Operating temperature

Relative humidity

908.42 MHz (US)

100-240VAC, 50/60Hz

< 0.5W

0 to 40°C

8% to 80%

Brief introduction of buttons

Inclusion/Exclusion” Button

Installation Guide

Please read carefully the enclosed user manual before installation of wall controller, in

order to ensure an error-free functioning.

The wall controller unit supplied as complete set for flush mounting in the standard US

Dimensions

Material

75x120x29.1mm

Tempered glass panel with capacitive touch buttons

Back side

19.4 mm 43.58 mm

65.58 mm

AC Power input

83.00 mm

Front side

L L N N

PRI:

Uin=100-240VAC

Iin=15mA MAX

Out=Z-Wave Signal

SR-ZV9002T3

-CCT-US

SW1

Z-Wave Controller

0% PWM1 + 100% PWM2

ALL ON/OFF button, broadcast to turn on/off all

LED indicator

Decrease whole brightness Increase whole brightness

Save and recall 3 scenes

Color Wheel for adjusting relative

brightness between PWM1 and PWM2

Group 4

100% PWM1 + 0% PWM2

50% PWM1 +50% PWM2

Group 2

Group 3

100% PWM1 + 0% PWM20% PWM1 + 100% PWM2

size wall boxes.

ATTENTION: Only authorized technicians under consideration of the country specific

installation guidelines/norms may do works with 100-240V mains power. Prior to the

assembly of the product, the voltage network has to be switched OFF and ensured

against re-switching.

Inclusion (Add the device to a Z-Wave network)

1. Set primary controller/gateway into inclusion mode (Please refer to your primary

controllers manual on how to turn your controller into inclusion).

2. Make sure the wall controller does not belong to any Z-Wave network (please refer to

the part “How to check whether the wall controller included to a network” of this manual).

3. Short press the “inclusion/exclusion” button, or press and hold down “ALL ON/OFF”

button for over 3 seconds, the wall controller will be set to inclusion mode, and waiting to

be included, then LED indicator turns on and blinks 6 times quickly to indicate

successful inclusion.

Once the wall controller quits “inclusion mode”, the LED indicator will turns off. There

are 3 methods for the wall controller to quit “inclusion mode”:

1. Automatically quits after successful inclusion.

2. Quits after 25 seconds timeout.

3. Press and hold down “ALL ON/OFF” button for over 3 seconds, or short press the

“inclusion/exclusion” button to quit.

Exclusion (Remove the device from a Z-Wave network)

There are two exclusion methods:

Method 1: Exclusion from the primary controller/gateway as follows:

1. Set the primary controller/gateway into exclusion mode (Please refer to your primary

controllers manual on how to set your controller into exclusion).

2. Short press the “inclusion/exclusion” button, or press and hold down “ALL ON/OFF”

button for over 3 seconds, the wall controller will be set to exclusion mode, and waiting

to be excluded, then LED indicator turns on and shows 3 short blinks and 1 long blink to

indicate successful exclusion.

Once the wall controller quits “exclusion mode”, the LED indicator will turns off. There

are 3 methods for the wall controller to quit “exclusion mode”:

1. Automatically quits after successful exclusion.

2. Quits after 25 seconds timeout.

3. Press and hold down “ALL ON/OFF” button for over 3 seconds, or short press the

“inclusion/exclusion” button to quit.

Method 2: Factory reset the wall controller will force the wall controller to be excluded

from a network. (please refer to the part “Factory Reset” of this manual)

Note: Factory reset is not recommended for exclusion, please use this procedure only if

the primary controller/gateway is missing or otherwise inoperable.

How to check whether the wall controller already included to a network

Operate any button to check if there is indication from the LED indicator, and no LED

indication means the wall controller does not belong to any network.

If the wall controller already belongs to a network, follow the exclusion process before

including it in your network. Otherwise inclusion of this device will fail.

Factory Reset

Press and hold down “inclusion/exclusion” button for over 8 seconds, LED indicator will

blink slowly to indicate successful factory reset, release “inclusion/exclusion” button,

the wall controller will restart automatically.

Association

Z-Wave devices control other Z-Wave devices. The relationship between one device

controlling another device is called association. In order to control a different device, the

controlling device needs to maintain a list of devices that will receive controlling

commands. These lists are called association groups and they are always related to

certain events (e.g. button pressed). In case the event happens all devices stored in the

respective association group will receive a common wireless command.

Association Groups:

Each group supports maximum 12 nodes for association, the same device can be

associated with multiple groups on the wall controller simultaneously, to ensure better

control experience, the wall controller shall remove the associated devices that are not

under working status from association groups in time.

Group

Identifier Group Name Max Nodes Description

1. Send “Command Class Device Reset

Locally” to associated devices of this

group to report factory reset information

when factory reset the wall controller.

2. Double click a group number of the wall

controller to send command to

associated devices of this group using

“Command Class Central Scene”.

1. Press and hold down button "1" to

activate group in order to switch the

associated devices with a Basic Set or

dim these devices by using the two

brightness buttons or adjust color

Lifeline

Launch 1

Set and unset associations:

(Note: All association information will be cleared automatically once the wall controller

is excluded from a network.)

Associations can be assigned and remove either via Z-Wave commands or using the

device itself.

1. Set association by operating primary controller/gateway to send packets to the wall

controller:

The primary controller/gateway sends packets to the wall controller using “Command

1. Press and hold down button "2" to

activate group in order to switch the

associated devices with a Basic Set or

dim these devices by using the two

brightness buttons or adjust color

temperature by using color wheel.

2. Short press Scene button S1/S2/S3,

direct control of associated devices using

Scene Activation Set, Scene ID = 0x10 /

0x20 / 0x30.

3. Press and hold down Scene button

S1/S2/S3, direct control of associated

devices using Scene Conf Set, Scene ID

= 0x10 / 0x20 / 0x30.

3Launch 2 12

1. Press and hold down button "3" to

activate group in order to switch the

associated devices with a Basic Set or

dim these devices by using the two

brightness buttons or adjust color

temperature by using color wheel.

2. Short press Scene button S1/S2/S3,

direct control of associated devices using

Scene Activation Set, Scene ID = 0x10 /

0x20 / 0x30.

3. Press and hold down Scene button

S1/S2/S3, direct control of associated

devices using Scene Conf Set, Scene ID

= 0x10 / 0x20 / 0x30.

4Launch 3 12

temperature by using color wheel.

2. Short press Scene button S1/S2/S3,

direct control of associated devices using

Scene Activation Set, Scene ID = 0x10 /

0x20 / 0x30.

3. Press and hold down Scene button

S1/S2/S3, direct control of associated

devices using Scene Conf Set, Scene ID

= 0x10 / 0x20 / 0x30.

2Launch 1 12

Class ASSOCIATION” or “Command Class Multi Channel Association”

2. Set association by operating the wall controller and devices to be controlled:

To control a Z-Wave device from the Wall Controller the node ID of this device needs to

be assigned to one of the four association groups. This is a three-step process:

1. Press and hold down “ALL ON/OFF” button on the wall controller for over 3 seconds,

LED indicator turns on.

2. Click any Group number button on the wall controller within 25 seconds to add the

device to be controlled to the association group, double click any Group number button

on the wall controller within 25 seconds to remove the device to be controlled to the

association group.

3. Operate the device to be controlled to send Node Information Frame (please refer to

the device manual) within 15 seconds, or set the device to exclusion mode within 15

seconds, since it will send Node Information Frame in exclusion mode, LED indications

are as follows:

LED blinks 5 times to indicate that the wall controller failed to add the associated device

(the association group has already added maximum quantity associated devices that it

supports ).

LED blinks 10 times to indicate that the wall controller added the associated device

successfully.

LED blinks 8 times to indicate that the wall controller removed the associated device

successfully.

To remove all associated devices in an association group on the wall controller directly:

1. Press and hold down “ALL ON/OFF” button on the wall controller for over 3 seconds,

LED indicator turns on.

2. Click any Group number button on the wall controller 5 times continuously within 25

seconds to remove all associated devices of this group, LED indicator blinks 8 times to

indicate that the associated devices are removed successfully.

Operating the device

0% PWM1 + 100% PWM2

ALL ON/OFF button, broadcast to turn on/off all

LED indicator

Decrease whole brightness Increase whole brightness

Save and recall 3 scenes

Color Wheel for adjusting relative

brightness between PWM1 and PWM2

100% PWM1 + 0% PWM2

50% PWM1 +50% PWM2

100% PWM1 + 0% PWM20% PWM1 + 100% PWM2

3 Groups

IP Rating

Frequency

IP 20

908.42 MHz (US)

Choose the objects you would like to control:

•

the objects which the command will be sent to.

• Short press Group number button 2, all associated devices of Association Group 3 are

the objects which the command will be sent to.

• Short press Group number button 3, all associated devices of Association Group 4 are

the objects which the command will be sent to.

Control the objects you would like to control:

• Double click Group number button 1-3, activation of scenes in Gateways using

Command Class Central Scene.

• Short press Scene button S1/S2/S3, direct control of associated devices using Scene

Activation Set, Scene ID = 0x10 / 0x20 / 0x30 to the last used Group 2, 3 or 4.

• Press and hold down Scene button S1/S2/S3, direct control of associated devices

using Scene Conf Set, Scene ID = 0x10 / 0x20 / 0x30 to the last used Group 2, 3 or 4.

• Short press “ALL ON/OFF” button, direct control of associated devices using Basic

Set On/Off commands.

• Short touch or slide touch the “Color Wheel”, direct control of associated devices

using Color Switch Set commands.

• Press and hold down brightness down and brightness up buttons, direct control of

associated devices using Multilevel Switch Start Level Change Set commands.

Node Information Frame

The Node Information Frame is the business card of a Z-Wave device. It contains

information about the device type and the technical capabilities. The inclusion and

exclusion of the device is confirmed by sending out a Node Information Frame. Beside

this it may be needed for certain network operations to send out a Node Information

Frame.

How to send out Node Information Frame:

Set the wall controller into inclusion/exclusion mode: press and hold down “ALL

ON/OFF” button for over 3 seconds, or short press the “inclusion/exclusion” button, LED

indicator turns on to indicate the wall controller has already sent out Node Information

Frame, the user can repeat the operation to set the wall controller to quit

“inclusion/exclusion mode”.

Technical Data

Short press Group number button 1, all associated devices of Association Group 2 are

Manufacturer Specific

Z-Wave Plus Info

Parameter

Z-Wave Plus Version

Role Type

Node Type

Installer Icon Type

User Icon Type

Value

Slave Always On

ZWAVEPLUS

0x1600 (ICON_TYPE_GENERIC_WALL_CONTROLLER)

Parameter

Manufacturer ID

Product Type ID

Product ID

Value (hex)

0x0330

0x0301

0xa101

COMMAND CLASS

Support S2

Wireless Range

SDK

Explorer Frame Support

Device Type

Generic Device Class

Specific Device Class

Routing

FLiRS

Up to 100 m outside, on average up

to 40 m inside buildings

6.71.01

Yes

Wall Controller

Basic Wall Controller

Yes

Node Info

COMMAND_CLASS_ZWAVEPLUS_INFO

COMMAND_CLASS_SECURITY

COMMAND_CLASS_SECURITY_2

COMMAND_CLASS_TRANSPORT_SERVICE

YES

Wiring diagram

AC 100-240V

AC Power

50/60Hz

Installation

L L N N

PRI:

Uin=1 00- 240VAC

Iin=1 5mA MA X

Out=Z -Wave S ignal

SR-ZV9002T3

-CCT-US

SW1

Z-Wave Controller

YES

COMMAND_CLASS_SUPERVISION

COMMAND_CLASS_MANUFACTURER_SPECIFIC

COMMAND_CLASS_VERSION

COMMAND_CLASS_ASSOCIATION_GRP_INFO

COMMAND_CLASS_MULTICHANNEL_ASSOCIATION

COMMAND_CLASS_CENTRAL_SCENE

COMMAND_CLASS_ASSOCIATION

COMMAND_CLASS_POWERLEVEL

COMMAND_CLASS_DEVICE_RESET_LOCALLY

COMMAND_CLASS_FIRMWARE_UPDATE_MD

COMMAND_CLASS_SWITCH_MULTILEVEL

COMMAND_CLASS_SWITCH_COLOR

COMMAND_CLASS_SCENE_ACTIVATION

COMMAND_CLASS_SCENE_ACTUATOR_CONF

COMMAND_CLASS_MARK

Other Sunricher Controllers manuals

Sunricher

Sunricher SR-2309PRO-5C User manual

Sunricher

Sunricher DMXWA-002 User manual

Sunricher

Sunricher SR-2411-ZG-DIM-A User manual

Sunricher

Sunricher SR-2834BDMX User manual

Sunricher

Sunricher SR-SBP2801K4-DIM-G2 User manual

Sunricher

Sunricher SR-2850RGB IT SR-2830RGB US User manual

Sunricher

Sunricher SR-2834B User manual

Sunricher

Sunricher DMX MASTER SR-2817 User manual

Sunricher

Sunricher SR-2411-ZG-DIM User manual

Sunricher

Sunricher SR-2834DMX-5C User manual

Sunricher

Sunricher C94-3ZW User manual

Sunricher

Sunricher SR-2812 User manual

Sunricher

Sunricher SR-2411-ZG User manual

Sunricher

Sunricher SR-2836DIM User manual

Sunricher

Sunricher SR-ZV9002T4-CCT-EU User manual

Sunricher

Sunricher SR-2820B User manual

Sunricher

Sunricher SR-2808 User manual

Sunricher

Sunricher SR-ZV9001T-DIM-EU User manual

Sunricher

Sunricher SR-ZV9080A-B User manual

Sunricher

Sunricher SR-2834-5C User manual

Sunricher

Sunricher SR-2812 User manual

Sunricher

Sunricher SR-2818-BLACK User manual

Sunricher

Sunricher SR-ZV9003T4-RGBW-EU User manual

Sunricher

Sunricher SR-10 Series User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual