Stratasys Objet Series Guide

Caution—

To avoid exposure to skin irritants,

wear protective gloves (provided)

throughout this procedure.

DOC-34032 Rev. A

B. Remove screws B.

C. Loosen screw C.

A. Put on protective gloves. Remove the print block cover.

A. Remove the Support print head card.

B. Loosen the print head thumb screws.

Removing the Support Print Head

Support Print Head Replacement Instructions

for Objet Desktop V3 Printers

Page 1

While holding the print head, press down

on the thumb screws and remove it.

DOC-34032 Rev. A

5Make sure you remove the two O-ring

seals along with the print head.

6Protect the print head from UV light if

you plan to re-install it.

Discard the print head

in accordance with

local regulations.

Install the print block cover.

Push on the tab and then pull the jig

downwards to remove it.

DOC-34032 Page 2

Rev. A

Tighten the print head thumb screws.

Press down firmly on the Support print

head card to attach it to the print block.

Installing the Support Print Head

FRONT

PUSH

FIRST

With the print head in the positioning jig,

align it as shown.

Make sure the O-ring seals

are installed on the print head.

FRONT

Remove

Push tab

A. Push jig upwards where marked “Push First.”

B. Push jig upwards where marked “Front.”

A. Insert and tighten screws A.

B. Tighten screw B.

Make sure that the Model head is installed as described in Model Print Head Replacement.

Remove the Model print head card.

Removing the Model Print Head

Model Print Head Replacement Instructions

for Objet Desktop V3 Printers

Page 3

B. Loosen the print head thumb screws.

DOC-34032 Rev. A

Make sure you remove the two O-ring

seals along with the print head.

2While holding the print head, press down

on the thumb screws and remove it.

To replace the Model print head, you must first remove the Support print head

(see page 1).

Protect the print head from UV light if

you plan to re-install it.

Discard the print head

in accordance with

local regulations.

Installing the Model Print Head

Page 4

DOC-34032 Rev. A

After you replace the Model print-head, re-install the Support head (see page 2).

Push on the tab and then pull the jig

downwards to remove it.

Tighten the print head thumb screws.

Press down firmly on the Model print

head card to attach it to the print block.

FRONT

PUSH

FIRST

Make sure the O-ring seals

are installed on the print head.

FRONT

With the print head in the positioning jig,

align it as shown.

3A. Push jig upwards where marked “Push First.”

B. Push jig upwards where marked “Front.”

FRONT

Remove

Push tab

Other Stratasys 3D Printer manuals

Stratasys

Stratasys Objet1000 Plus Operating instructions

Stratasys

Stratasys Fortus 900mc Operating instructions

Stratasys

Stratasys Eden250 User manual

Stratasys

Stratasys Eden260V User manual

Stratasys

Stratasys Mojo User manual

Stratasys

Stratasys ProBleacher User manual

Stratasys

Stratasys Fortus 900mc User manual

Stratasys

Stratasys Eden260V User manual

Stratasys

Stratasys Objet350 User manual

Stratasys

Stratasys F120 Operating instructions

Stratasys

Stratasys uPrint User manual

Stratasys

Stratasys Origin One User manual

Stratasys

Stratasys F770 User manual

Stratasys

Stratasys uPrint SE Operating instructions

Stratasys

Stratasys Fortus 250mc User manual

Stratasys

Stratasys Objet30 User manual

Stratasys

Stratasys Dimension 768/Elite User manual

Stratasys

Stratasys RK1600 WJ User manual

Stratasys

Stratasys Objet24 User manual

Stratasys

Stratasys J750 User manual

Stratasys

Stratasys J750 User manual

Stratasys

Stratasys FDM 200mc User manual

Stratasys

Stratasys Objet24 V2 Operating instructions

Stratasys

Stratasys 180-00108 uPrint User manual

Popular 3D Printer manuals by other brands

Ultimaker

Ultimaker S5 Material Station installation guide

EcubMaker

EcubMaker TOYDIY quick start guide

AnyCubic

AnyCubic Kossel Plus Modification

ReDeTec

ReDeTec ProtoCycler Operation manual

Kywoo3D

Kywoo3D Tycoon IDEX user manual

CraftBot

CraftBot PLUS PRO user guide

3DGence

3DGence INDUSTRY F340 user manual

HP Jet Fusion 4200 Product Documentation Site Preparation Guide

Rokit

Rokit AEP Series user manual

AnkerMake

AnkerMake M5 user manual

DIYElectronics

DIYElectronics PRUSA I3 ELECTRONICS AND SOFTWARE GUIDE

Ackuretta

Ackuretta FreeShape 120 user manual

LONGER

LONGER LK5Pro manual

MakerBot

MakerBot Replicator user manual

ZYYX

ZYYX Pro II user manual

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Startup guide

LONGER

LONGER LK4 Pro quick start guide

German RepRap

German RepRap X400 Pro V3 user guide