STO GYGimbal User manual
Instruction
Manual
2-axis handheld stabilizing gimbal for GOPRO
Package Contents
Note:
Install the GOPRO before
connecting power.
Camera Holder
Gopro3
GOPRO3 LCD BacPac
Use the M2x33mm thumb
screw for GOPRO with LCD
BacPac.
Reverse the camera for selfie.
Assemble without M2x23mm Thumb
screw for external LCD BacPac.
The handle is 115 degree adjustable.
115°
18350
Rechargeable
battery x2
Power Switch
①②
V1.0
Signal light
DOWN
UP
MODE
1
1
2
2
1
2
1
1
1
1
2-axis handheld gimbal
Camera Holder
M2x23mm Thumb Screw
M2x33mm Thumb Screw
18350 Rechargeable Battery Charger
18350 Rechargeable Battery
Micro USB Charger Cable
Warranty Card
Certificate
User's Manual
Micro USB
port – for setting
and firmware
upgrade
www.standard-tec.com
③④
⑤⑥
90°
50°
50°
Horizon
The angle between roll axis and the horizon should not over
50 degree; or the stabilizer would be in safe mode, and the
stability would be affected.
UP
DOWN
UP
DOWN
In tilt adjust mode, user
can adjust tilt angle
through UP/DOWN
button.
In roll adjust mode, user
can adjust roll angle
through UP/DOWN button.
Charger indicator
(The signal will show green
once finish charging)
Micro USB 5V
power input port
18350 Rechargeable battery charger
Input: DC 5V/800mA
Output: DC 2.4V/400mA x2
Rechargeable Battery
Battery type: 18350 Li battery
Capacity: 900mAh
Charge Time: 3 hours
Note: For connecting power to 18350
battery charger, please prepare portable
charger, or connect to a USB port of PC.
Operation:
Specification:
minimum standard
maximum
Note
6.8V 8.4V 12V
50mA 100mA 2A
±0.01° ±0.04°
±0.1° ±0.2° ±0.5°
-90° 0° +90°
-50° 0° +50°
50°/S
3h 5h 6h
900mAh×2
245g
-20℃25℃45℃
90°
10°/S
●
●
●
●
●
Working Voltage
Working Current
Tilt Working Angle
Roll Working Angle
Tilt Angle Speed
Roll Angle Speed
Operation Temperature
Weight
without battery
and camera
Install the battery and press the power switch, the stabilizer will be in
standby mode. Press the power switch again to cut off power.
After connecting to power, long press “MODE” for 2~5 second to
switch standby mode/ performance mode.
In performance mode, press “MODE” to switch Tilt adjust mode/ Roll
adjust mode. LED fast blinking once: tilt adjust mode; LED fast
blinking twice: roll adjust mode.
Adjust the camera angle through UP/ DOWN buttons.
The signal light between tilt motor is the battery indicator. There
are four statuses: fast blinking once, twice, three times,
and four times. Fast blinking four times means the
battery is full-charged; fast blinking once means the
battery is low capacity, please recharge.
Battery Operation Time
(25°C)
Following Accuracy
(Motionless)
Following Accuracy
(Motion)
Power Switch
On/Off
Mode Switch
Angle Adjusting
Battery Indicator
:
:
:
:
:
This device has been calibrated by the
manufacturer. Warranty void if
disassemble any parts.
For user instruction, firmware upgrade,
and more informations, please visit :
www.standard-tec.com/
Table of contents
Other STO Camera Accessories manuals
Popular Camera Accessories manuals by other brands
Viltrox
Viltrox EF-NEX Mount instructions
Calumet
Calumet 7100 Series CK7114 operating instructions
Ropox
Ropox 4Single Series User manual and installation instructions
Cambo
Cambo Wide DS Digital Series Main operating instructions
Samsung
Samsung SHG-120 Specification sheet
Ryobi
Ryobi BPL-1820 Owner's operating manual
