Steren COM-203 User manual
Before using your new USB to IrDA adapter, please read this
instruction manual to prevent any damage. Put it away in a safe
place for future references.
IMPORTANT
Clean only with a soft, dry cloth.
Warranty is void if you open the device.
Do not use or store it near wet places.
CONTENT
1 USB to IrDA adapter
1 CD with drivers
FEATURES
Simple to connect, using an USB port
USB Plug and Play convenience
Fully compatible with IrDA and USB
No power adapter required
Low power consumption
•
•
•
•
•
•
•
•
ENGLISH
ENGLISH-2
SYSTEM REQUIREMENTS
PC 482DX4-100 MHz or higher
Available USB port
CR-ROM drive
Windows 98, ME, 2000, XP
INSTALLING DRIVER IN XP
Please, install the drivers rst before to plug the USB to IrDA
adapter.
1.- Load the CD with drivers into the CD-ROM.
2.- In the Welcome window, press Next.
•
•
•
•
ENGLISH
ENGLISH-3
3.- Select the desired language for installation, then press Aceptar.
4.- Select the option Install Device Driver.
ENGLISH
ENGLISH-4
5.- The driver will be installed and you must restart PC, press Ok.
6.- Plug the IrDA adapter to an available USB port.
7.- The computer will detect the new hardware and the new hardware
wizard will run.
8.- Select the option: Not in this moment, and press Next to continue.
ENGLISH
ENGLISH-5
9.- Select Install the software automatically (recommended), then
press Next.
10.- A Warning message may displays while installing, simply press
Continue to resume the installation, otherwise you will cancel the
installation.
ENGLISH
ENGLISH-6
11.- Press Finish to conclude the update.
12.- At this moment, the hardware is correctly installed and you can
begin its use.
When you install the driver, you can see an option to select a
mobile, please do not make any change, the performance will
not be affected.
ENGLISH
ENGLISH-7
HOW TO TRANSFER FILES FROM AN
INFRARED DEVICE TO PC AND VICE VERSA
Transferring les from an infrared device to the computer:
1.- Enable the infrared sensor in your device (PDA, mobile).
2.- Choose the desired le to transfer to PC.
3.- Press Send or Beam (depending of the device).
4.- Place the infrared sensor of the device in front of the IrDA
adapter.
5.- The computer will detect the incoming element and will request
if you want to accept it or not. Then press Yes to accept it. If you
choose No, you will cancel the transferring.
6.- If you choose Yes, the le transferring begins.
ENGLISH
ENGLISH-8
Once the transferring ends, a message will warning you about the
correct or incorrect data transfer. If this happen, repeat the process
again.
Refers to infrared device user’s manual to know what kind of
les you can transfer and the way to enable the infrared sensor.
ENGLISH
ENGLISH-9
Transferring le from PC to an IR device:
1.- Place the device that you want to use as receiver in front of the
adapter. Now, the IrDA adapter will detect the device.
2.- Press over the IR icon.
3.- In the new window, select the desired le to transfer, then press
Send.
ENGLISH
ENGLISH-10
Table of contents
Other Steren Adapter manuals
Steren
Steren COM-875 User manual
Steren
Steren USB-PAR User manual
Steren
Steren ELE-9230BL User manual
Steren
Steren COM-865 User manual
Steren
Steren 905-105 User manual
Steren
Steren POD-158 User manual
Steren
Steren ELI-1050 User manual
Steren
Steren COM-260 User manual
Steren
Steren 506-430 User manual
Steren
Steren COM-843 User manual
Steren
Steren USB-110 User manual
Steren
Steren COM-400 User manual
Steren
Steren COM-130 User manual
Steren
Steren VGA-256 User manual
Steren
Steren POD-081 User manual
Steren
Steren COM-452 User manual
Steren
Steren COM-437 User manual
Steren
Steren ELI-1230 User manual
Steren
Steren COM-473 User manual
Steren
Steren ELI-1250 User manual
