Star Micronics LC-1011C User manual
DOTMATRIXPRINTER
LC-1011C
LC-100+COLOUR
TECHNICAL MANUAL
[SECOND EDITION]
NOTICE
•Allrightsreserved.Reproductionofanypartofthismanualinany
form whatsoever, without STAR’s express permission is forbid-
den.
•The contents of this manual are subject to change without notice.
•All efforts have been made to ensure the accuracy of the contents
of this manual at the time of going to press. However, should any
errors be detected, STAR would greatly appreciate being in-
formed of them.
•The above notwithstanding, STAR can assume no responsibility
for any errors in this manual.
© Copyright 1996 Star Micronics Co.,Ltd.
1
2
3
4
5
6
7
INTRODUCTION
This manual is an introduction to dot matrix printers as shown below.
It is designed for use as a reference for periodic inspections and maintenance procedures to be executed by
service personnel. It is not intended for the general user. Users of this manual should have a basic knowledge
and understanding of the English language.
Model Destination
LC-1011C For American, Asia and Pacific market
LC-100+COLOUR For European market
•This manual is divided into the following sections:
Chapter 1 General Specifications
Chapter 2 Theory of Operation
Chapter 3 Adjustments
Chapter 4 Parts Replacement
Chapter 5 Maintenance and Lubrication
Chapter 6 Troubleshooting
Chapter 7 Parts List
CHAPTER 1
GENERAL SPECIFICATIONS
1. General Specifications .........................................................................................3
2. External Appearance and Composition ..............................................................5
3. Control Panel.........................................................................................................6
3-1. Switch Combination Functions .............................................................................6
3-2. EDS Mode Settings .................................................................................................6
4. Parallel Interface ...................................................................................................8
4-1. General Specifications ...........................................................................................8
4-2. Connector Signals ..................................................................................................8
5. Serial Interface (option) ........................................................................................9
5-1. General Specifications ...........................................................................................9
5-2. Connector Signals and Functional Descriptions ................................................ 9
5-3. DIP Switch Settings ..............................................................................................10
6. EE-PROM Mode ...................................................................................................11
6-1. Outline....................................................................................................................11
6-2. Explanation of Special Control Codes ............................................................... 11
6-3. EE-PROM Map .......................................................................................................12
6-4. Rewriting the EE-PROM........................................................................................16
1
– 2 –
GENERAL SPECIFICATIONS
– 3 –
GENERAL SPECIFICATIONS
1. General Specifications
Printing System Serial Impact Dot-Matrix
Printing Speed Pitch Draft (cps/dpi) NLQ (cps/dpi)
Pica (10 cpi) 160/120H 40/240H
Elite (12 cpi) 192/120H 48/240H
Condensed pica (17 cpi) 137/240H 69/240H
Condensed elite (20 cpi) 160/240H 80/240H
H: half-dot
Print Direction Draft: Bi-directional logic seeking
NLQ: Uni-directional or bi-directional logic seeking (selectable)
Bit-Image: Uni-directional
Print Head Number of pins: 9
Life: 200 million dots/pin
Line Spacing 1/6", 1/8"
7/72", n/72", n/216": software
Font Styles Draft, NLQ (Courier, Sanserif)
Character Matrix Pitch Draft NLQ
Pica (10 cpi) 9 ×11 18 ×23
Elite (12 cpi) 9 ×9 18 ×19
Condensed pica (17 cpi) 9 ×11 18 ×12
Condensed elite (20 cpi) 9 ×9 18 ×10
Environment Operating temperature: 41°F to 95°F (5°C to 35°C)
Storage temperature: -22°F to 149°F (-30°C to 65°C)
Operating humidity: 30% to 80% (non-condensing)
Storage humidity: 20% to 90% (non-condensing)
Paper Cut-sheet (manual feeding)
Paper width: 5.5" to 8.5" / 140 to 216 mm
Paper length: 5.5" to 14" / 140 to 356 mm
Paper thickness: 0.00276" to 0.00472" / 0.07 to 0.12 mm
Paper weight: 14 to 24 lbs. / 52 to 90 g/m2/ 45 to 77 kg
Cut-sheet (with optional automatic sheet feeder)
Paper width: 7.17" to 8.5" / 182 to 216 mm
Paper length: 10.12" to 14" / 257 to 356 mm
Paper thickness: 0.00315" to 0.00472" / 0.08 to 0.12 mm
Paper weight: 16 to 24 lbs. / 60 to 90 g/m2/ 52 to 77 kg
– 4 –
GENERAL SPECIFICATIONS
Fanfold (with push tractor feeder)
Paper width: 4" to 10" / 101.6 to 254 mm
Paper thickness: 0.00276" to 0.00433" / 0.07 to 0.11 mm (one-ply)
0.00984" / 0.25 mm max.
(total thickness of multi-ply paper)
Paper weight: 14 to 22 lbs. / 52 to 82 g/m2/ 45 to 70 kg (one-ply)
11 to 14 lbs. / 40 to 52 g/m2/ 34 to 45 kg (multi-ply)
Copies: Original + 2
Emulation (AEC) Standard Mode: EPSON ESC/P (9-pin)
IBM Mode: Proprinter III
Interface Standard: Centronics parallel
Option: RS-232C serial
Ribbon Type On-carriage, dedicated
Color ribbon (standard)
Fabric monochrome ribbon (option)
Ribbon Life Color ribbon (LC9CL): 0.5 million characters (draft pica, black)
Fabric monochrome ribbon (LC9HD): 1 million characters (draft pica)
Long-life fabric monochrome ribbon (LC9W): 2.5 million characters (draft pica)
Power Supply 110V AC 10%, 120V AC 10%, 230V AC +6%/-14%, 240V AC 10%; 50/60Hz
(depending on country of purchase)
Power Consumption 34W during ASCII draft printing
8W during stand-by
Options SF-10DT Single-bin Automatic Sheet Feeder
SPC-8K Serial-To-Parallel Converter
Fig. 1-1 External dimensions
– 5 –
GENERAL SPECIFICATIONS
2. External Appearance and Composition
Fig. 1-2 Front View of the Printer
Fig. 1-3 Diagram of Internal Composition
– 6 –
GENERAL SPECIFICATIONS
3. Control Panel
3-1. Switch Combination Functions
Fig. 1-4 Switch combination functions
DRAFT
COURIER
10CPI
12CPI
SANSERIF FONT
ALT
QUIET
POWER
PROP
COND
PITCH
MACRO
PAPER FEED
PARK
QUIET ON LINE
On-Line
CLEAR
FF
MICRO FEED
Form Feed
Line FeedPitchFont
Off-Line
QuietShort Tear-offLong Tear-off
Forward
Save Macro
Font & Pitch Lock EE-PROM Mode
Buffer Clear & All Reset
AUTO LOADING POSITION CHANGE MODE
Paper Park
OFF-LINE
ExitOn/offSwitchBank
POWER-ON
Exit
NextRightLeft
EDS MODE
DOT-ADJUSTMENT MODE
Short TestLong TestPitch LockFont Lock
ON-LINE
Hex Dump Mode
Dot Adjustment Mode
EDS Mode
Aging Mode
Backward Micro Feed
Set TOF
Print
CancelForwardBackward
Set
Save
Factory setting AUTO LOADING POSITION CHANGE MODE
Other manuals for LC-1011C
1
This manual suits for next models
2
Table of contents
Other Star Micronics Printer manuals
Star Micronics
Star Micronics TSP400Z Series User manual
Star Micronics
Star Micronics LS-5 SERIES User manual
Star Micronics
Star Micronics LC-8211 User manual
Star Micronics
Star Micronics TSP043E Series User manual
Star Micronics
Star Micronics NX-1000 User manual
Star Micronics
Star Micronics TUP592 User manual
Star Micronics
Star Micronics SJ-144MC User manual
Star Micronics
Star Micronics Star SCP700 Series Operating and maintenance manual
Star Micronics
Star Micronics DP8340RC Series User manual
Star Micronics
Star Micronics DP8340 Series User manual
Star Micronics
Star Micronics LC-7211 User manual
Star Micronics
Star Micronics SP500 Series User manual
Star Micronics
Star Micronics TUP400 Series User manual
Star Micronics
Star Micronics TUP900 Series User manual
Star Micronics
Star Micronics TSP 654IID User manual
Star Micronics
Star Micronics NX-1020 User manual
Star Micronics
Star Micronics NP-266 Installation instructions
Star Micronics
Star Micronics SB-10 User manual
Star Micronics
Star Micronics TSP200 Series Operating and maintenance manual
Star Micronics
Star Micronics NX-1020 User manual
