1080 Centre Rd. Suite C
Auburn Hills, MI 48326
www.fortrezz.com
Phone: (248) 481-7092
sales@fortrezz.com
Choosing a mounting location
This unique, contemporary siren has a smooth, paintable surface that easily blends with any decor. It mounts to any flat surface wall or ceiling and
is suitable for use in dry, interior locations only. Avoid placing the SSA1 close to a metal frame, or other metal enclosures that may affect RF
range. Suggested SSA1 uses: various alarms in home automation and home security systems and alerts for water leak or water level detection.
Main Power Dropout and Replacing the 9V Backup Battery
If main power drops, the SSA1 will continue to operate on the 9V battery, but, if triggered, will only sound the Siren for approx. 5 seconds and flash
the Strobe for 30 seconds. Also, two seconds after power drops, the SSA1 will sound the siren for 5 seconds and strobe the LEDs for 30 seconds
if a 9V battery is installed. Power dropout status can be monitored by a controller, using the Alarm Command Class Version 2. The controller must
enable power dropout monitoring in the SSA1 by using the Alarm Set command. If the 9V backup battery is not discharged, the SSA1 will send an
alert to that controller at regular intervals when it detects that main power has dropped out. In addition, the status LED will periodically blink.
Under power dropout conditions, if the SSA1’s periodic alerts are not being received, this might be an indication that the backup battery has
discharged or that transmissions from the SSA1 can no longer be routed (perhaps because of power off to the entire house). The 9V backup
battery should be replaced once per year or more often if main power drops out. Do not install batteries that appear damaged or unsealed.
FCC Compliance Statement Statements Contains Transmitter Module FCC ID: XCT-Z3US
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
CAUTION: To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20cm or more
should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this
distance is not recommended.
Canada: Industry Canada Statement per Section 4.0 of RSP-100.
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
From section 7.1.5 of RSS-GEN. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2)
This device must accept any interference received, including interference that may cause undesired operation.
From section 7.1.1 RSS-Gen, Issue 2, June 2007 a) The host device, as a stand-alone unit without any separately certified modules, complies
with all applicable Radio Standards Specifications. b) The host device and all the separately certified modules it contains jointly meet the RF
exposure compliance requirements of RSS-102, if applicable. c) The host device complies with the certification labeling requirements of each of
the modules it contains.
From section 5.2, RSS-Gen, Issue 2, June 2007 Equipment Labels: Contains IC: 8156A-Z3X
From section 7.1.6, RSS-Gen, Issue 2, June 2007 Digital Circuits: If the device contains digital circuitry that is not directly associated with the
radio transmitter, the device shall also have to comply with ICES-003, Class A or B as appropriate, except for ICEC-003 labeling requirements. The
test data obtained (for the ICES-003 tests) shall be kept by the manufacturer or importer whose name appears on the equipment label, and made
available to Industry Canada on request, for as long as the model is being marketed in Canada.
Europe
The SSA1 module has been certified for use in European countries. Completed testing: Test standard: ETSI EN 300 328 V1.7.1 (2006-10).
The W aste Electrical and Electronic Equipment (WEEE) directive (2002/96/EC) was approved by the European Parliament and the
Council of the European Union in 2003. This symbol indicates that this product contains electrical and electronic equipment that
may include batteries, printed circuit boards, liquid crystal displays or other components that may be subject to local disposal
regulations at your location. Please understand those regulations and dispose of the product in a responsible manner.
LIMITED WARRANTY
THE PRODUCT IS PROVIDED WITH ONE YEAR LIMITED MANUFACTURER WARRANTY. FORTREZZ, LLC warrants its
products to be free from defects in material and workmanship under normal use for one year, and is not responsible for
consequential damages or installation costs of any nature. FORTREZZ, LLC. expressly disclaims all implied warranties, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose. FORTREZZ, LLC does not warrant,
guarantee, or make any representations regarding the use or the results of the use of the products or any accompanying materials
in terms of their correctness, accuracy, reliability or otherwise. In no event shall FORTREZZ, LLC. be liable to Purchaser hereunder
or in respect of any products ordered or delivered to Purchaser, whether in contract, tort including negligence or otherwise for a
loss of profits or loss of use or for any incidental, consequential, special or indirect damages howsoever caused whether or not
FORTREZZ, LLC. has been advised of the possibility of such loss or damage. FORTREZZ, LLC's maximum liability to Purchaser
under these conditions shall in no event exceed the amount paid by Purchaser for the products that are the subject of the claim and
in respect of all claims for products ordered from FORTREZZ, LLC to which these conditions apply to the amount paid by
Purchaser for the products which are the subject of the claims.
If you are not comfortable with your limited warranty, or not completely satisfied with the SSA1, or the SSA1 does not perform as expected we
encourage you to return the SSA1 to your DISTRIBUTOR for an exchange or forv a full refund within 30 days of purchase. Or, you can return the
SSA1 to FORTREZZ with an RGA number. All products to be returned to FORTREZZ, LLC. must have a valid Returned Goods Authorization
(RGA). Send the returned unit to: FortrezZ, LLC Warranty Replacement, 1080 Centre Rd. Suite C Auburn Hills, MI 48326, return postage
prepaid. You must use the original packaging and include a proof of purchase (photocopy of receipt) along with the RGA #.
093010
