Sony NSS-V2 User manual
INSTALLATION MANUAL
1st Edition (Revised 1)
MULTI-FORMAT MEDIA SERVER
NSS-V2
DIGITAL INPUT PROCESSOR BOARD
BKNS-V202
DIGITAL OUTPUT PROCESSOR BOARD
BKNS-V203
9PIN CONTROL INTERFACE BOARD
BKNS-V209
NSS-V2
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
NSS-V2 Serial No.10001 and Higher
BKNS-V202 Serial No.10001 and Higher
BKNS-V203 Serial No.10001 and Higher
BKNS-V209 Serial No.10001 and Higher
WARNING
This unit has no AC power switch.
When installing the unit, incorporate a readily
accessible disconnect device in the fixed wiring, or
connect the power cord to a socket-outlet which must
be provided near the unit and easily accessible, so that
the user can turn off the power in case a fault should
occur.
WARNUNG
Dieses Gerät hat keinen AC-Netzschalter.
Beim Einbau des Geräts ist daher im Festkabel ein
leicht zugänglicher Unterbrecher einzufügen, oder das
Netzkabel mu
ß
mit einer in der Nähe des Geräts
befindlichen, leicht zugänglichen Wandsteckdose
verbunden werden, damit sich bei einer
Funktionsstörung die Stromversorgung zum Gerät
jederzeit unterbrechen lä
ß
t.
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to the
following port(s).
: 100BASE-TX connector
Follow the instructions for the above port(s).
NSS-V2 1 (P)
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.
6. When performing the installation, keep the
following space away from walls in order to
obtain proper exhaust and radiation of heat.
Rear: 10 cm (4 inches) or more
Laser Diode Properties
Wave length : 850 nm
Emission duration : Continuous
Laser output power : 0.5 mW (max.) (Specification
of an optical pickup)
CAUTION
The use of optical instruments with this product
will increase eye hazard.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein
may result in hazardous radiation exposure.
This Multi-format Media Server is classified as a CLASS
1 LASER PRODUCT.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
NSS-V2
2 (P)
PRECAUTIONS
Use the specified power cord only
Use of power cords other than the specified ones may
cause fire or electric shock.
Do not damage the power cord
A damaged power cord may cause fire or electric shock.
When mounting the unit in a rack, be careful not to
catch the power cord in the rails.
Do not install the unit in humid or dusty locations
Dust, soot, and oil particles in the ambient atmosphere
may cause fire or electric shock.
Install the dedicated circuit breaker or power switch
This unit is not equipped with an AC power switch.
Install the dedicated circuit breaker or power switch,
and/or plug the power cord in the outlet.
Do not block the ventilation slots
If the ventilation slots are blocked, overheating inside
the unit may cause fire. Observe the following points to
ensure adequate ventilation.
.Do not install in narrow or sealed locations.
.Remove dust from the fan and air filter.
Install in a stable location
Installation in an unstable place may cause the unit fall,
resulting in injury.
Do not stack the units
Do not stack two or more units on top of each other.
Mount in a rack to avoid the risk of the unit sliding and
causing injury.
Ground the unit safely
Failure to ground the unit may cause electric shock.
Handling the unit by holding the designated
positions
When handling the unit, be sure to hold the following
positions.
Otherwise, the unit may break and fall, causing injury.
.Rack angle
.Bottom case
Especially, do not hold the front panel or the handle of
the power supply unit.
Carry the unit with more than two persons
The total weight of this unit is 21 kg.
Carrying the unit with less than two persons may cause
injury.
Mount with more than two persons
The total weight of this unit is 21 kg.
Mounting the unit with less than two persons may cause
injury.
Mount only with the specified rack mount rails
Rack mount rails other than those specified for this unit
may not be strong enough to support the unit, risking
possible collapse and injury.
Secure the unit to a rack with the screws
If the unit is not secured completely, this may cause the
unit fall off, resulting in injury. Be sure to secure the unit
with the screws when mounting to the rack. (Refer to
“1-4. Rack Mounting”)
Plug and connector of the power cord must be
inserted as far as they can go
Plug and connector of the power cord must be inserted
into the AC inlet as far as they can go.
1 (E)
NSS-V2
Table of Contents
Manual Structure
Purpose of this manual ........................................................... 3 (E)
Related manuals ..................................................................... 3 (E)
Contents .................................................................................. 3 (E)
Trademarks ............................................................................. 3 (E)
1. Installation
1-1. Installation Procedure .............................................. 1-1 (E)
1-2. Operating Conditions and Installation Space .......... 1-2 (E)
1-3. Power Supply ........................................................... 1-4 (E)
1-3-1. Information for Power Supply ........................ 1-4 (E)
1-3-2. Recommended Power Cord ............................ 1-4 (E)
1-4. Rack Mounting ........................................................ 1-5 (E)
1-5. Installing the Option Boards .................................... 1-7 (E)
1-5-1. Installing the BKNS-V202/V203 ................... 1-7 (E)
1-5-2. Installing the BKNS-V209 ............................. 1-8 (E)
1-6. Signal Input and Output ........................................... 1-9 (E)
1-7. Connecting Connectors and Cables ....................... 1-10 (E)
1-8. Connection ............................................................. 1-11 (E)
1-9. Setting after Installation ......................................... 1-12 (E)
2. Service Overview
2-1. Cleaning the Air Filter ............................................. 2-1 (E)
2-2. Functional Descriptions of Board Switches
and LEDs ................................................................. 2-2 (E)
2-2-1. FC-100 Board ................................................. 2-2 (E)
2-2-2. SY-318 Board ................................................. 2-3 (E)
2-2-3. TM-45 Board .................................................. 2-4 (E)
2-2-4. MPU-136 Board ............................................. 2-5 (E)
2-2-5. ENC-90 Board (BKNS-V202) ....................... 2-6 (E)
2-2-6. DEC-154 Board (BKNS-V203) ..................... 2-7 (E)
2-2-7. IF-972 Board (BKNS-V209) .......................... 2-8 (E)
2-3. Operating Setup Tool ............................................... 2-9 (E)
2-3-1. Setup Tool Descriptions ............................... 2-10 (E)
2-3-2. Changing Setup Table .................................. 2-11 (E)
2-3-3. Changing the Setup Values using
Dynamic Setup ............................................. 2-12 (E)
2-4. Building File Manager-PC ..................................... 2-18 (E)
2-4-1. Preparation ................................................... 2-18 (E)
2-4-2. Installation .................................................... 2-19 (E)
2-4-3. Others ........................................................... 2-19 (E)
2-5. Installing Transfer Manager .................................. 2-22 (E)
2-5-1. Preparation ................................................... 2-22 (E)
2-5-2. Installation .................................................... 2-22 (E)
2-5-3. Startup/Stop .................................................. 2-29 (E)
2-6. Setting McDATA FC Switch ................................. 2-31 (E)
2-6-1. Preparation (Setting the IP Address) ............ 2-31 (E)
2-6-2. Setting the Switch ......................................... 2-31 (E)
3 (E)
NSS-V2
Purpose of this manual
This manual is the installation manual of Multi-format Media Server NSS-V2.
This manual is intended for use by trained system and service engineers, and
describes the information regarding installation.
Related manuals
Besides this Installation Manual, the following manuals are available for the
NSS-V2.
..
..
.NSS-V2 Operation Manual (supplied with the NSS-V2)
This manual describes the application and operation of the NSS-V2.
Part number: 3-903-845-XX
..
..
.NSS-V2 Maintenance Manual (available on request)
This manual describes the information that premise the service based on main
parts replacement (service overview, maintenance functions, replacement of the
parts and boards, circuit descriptions and block diagram, etc.).
If this manual is required, please contact your local Sony Sales Office/Service
Center.
Part number: 9-968-190-XX
Contents
The following is a summary of all the section for understanding the contents of this
manual.
Section 1 Installation
Explains the operating conditions, installation space, power supply, installation of
option board, rack mounting, connection, and checks after connection.
Section 2 Service Overview
Explains the procedure for cleaning the air filter, the function and factory setting of
the switches and LEDs on the board, procedures for operating Setup Tool, building
File Manager-PC, installing Transfer Manager, and setting McDATA FC Switch.
Trademarks
Trademarks and registered trademarks used in this manual are follows.
.Ethernet is a registered trademark of Xerox Corporation.
.Pentium is a registered trademark of Intel Corporation.
.Linux is a registered trademark of Linus Torvalds.
.Red Hat is a registered trademark of Red Hat, Inc.
.TimeSys and Time Sys Linux are registered trademarks of TimeSys Corp.
Manual Structure
1-1 (E)
NSS-V2
Section 1
Installation
1-1. Installation Procedure
The installation procedure of the NSS-V2 is shown in the following flowchart.
Refer to each item in this manual for details.
This unit is supplied with the following parts.
.Plug Holder 2 pcs
.Ornamental Washer 4 pcs
.Screw (RK5 x16) 4 pcs
.Operation Manual 1 pc
.Installation Manual 1 pc
.File Manager Software CD-ROM 1 pc
The following equipment is prepared
.The personal computer for installing the File Manager software
OS: Red Hat Linux ES, TimeSys Linux
CPU: Intel Xem 3.4 GHz or more
Memory: 2 GB or more
HDD: 36 GB or more
Ethernet: 100Base-TX
n
For the newest information on the personal computer, please contact your local Sony Sales Office/
Service Center.
Start
Determination
of Installation Space
Rack Mounting
Installation of
Option Boards
Connection
End
1-2. Operating Conditions
and Installation Space
1-3. Power Supply
1-4. Rack Mounting
1-5. Installation of Option Boards
1-6. Signal Input and Output
1-7. Connecting Connectors and Cables
1-8. Connection
1-2 (E) NSS-V2
1-2. Operating Conditions and Installation Space
Operating Conditions
Operating temperature +5 dC to +40 dC
Performance humidity 10 % to 90 % (No condensation)
Mass NSS-V2 : Approx. 21 kg
BKNS-V202 : Approx. 1 kg (per one set)
BKNS-V203 : Approx. 1 kg (per one set)
BKNS-V209 : Approx. 1 kg (per one set)
To prevent overheating of the NSS-V2 ensure that there is good air circulation around the unit.
w
Do not install the unit in humid or dusty environment.
c
Do not stack the units.
Other manuals for NSS-V2
1
Table of contents
Other Sony Server manuals
Sony
Sony MAV-1000 User manual
Sony
Sony NSR-500 User manual
Sony
Sony WG-C10 Series Operating manual
Sony
Sony Ipela NSR-1200 User manual
Sony
Sony VGF-HS1 - Vaio Home Server User manual
Sony
Sony WG-C10 Series Reference guide
Sony
Sony HDXS-C200 User manual
Sony
Sony IPELA PCS-RS User manual
Sony
Sony XDS1000 User manual
Sony
Sony NSR-1000 Series User manual
Sony
Sony NSR-500 User manual
Sony
Sony MAV-70 User manual
Sony
Sony NSR-1000 Series User manual
Sony
Sony Ipela SNT-EX101 User manual
Sony
Sony RM-PP1 User manual
Sony
Sony VGF-HS1 - Vaio Home Server User manual
Sony
Sony IPELA NSR Series User manual
Sony
Sony WG-C20 Series User manual
Sony
Sony NSS-V2 User manual
Sony
Sony StorStation FSV-M3 User manual
