Sony SRG 300 User manual
SKAARHOJ DEVICE CORES
Device: Sony SRG 300
Introduction
A large number of parameters can be controlled on the Sony SRG 300cameras.
This integration was done using Sony SRG 300 software version 1.0.
Please see the “PTZ Manual” at https://www.skaarhoj.com/support/manuals/ to learn more about PTZ
control in general from SKAARHOJ controllers and in particular network recommendations.
In this manual it is worth noticing that one should not add additional Device Cores to control multiple
cameras. This is possible from the same Device Core but proper steps should be ensured (consecutive IP
addresses on the cameras) for a good user experience.
Number of Cameras possible to control
Please notice from the Sony SRG 300 Device Core it is possible to control up 7 cameras. In general this is
the limit for our VISCA over IP Device Cores and our integration have not been tested above 7 cameras. If
you want to control more than 7 cameras you will need to add an additional Device Core and configure
the controller accordingly. None of our default configuration utilities 2 x Sony SRG 300 Device Cores. As
we have never tested with more than 7 cameras, we do not know how performance and stability will be in
such a configuration setup. We recommend only having 1 x Sony SRG 300 Device Core installed per
controller.
1
SKAARHOJ DEVICE CORES
Confirm Connection
The Serial Monitor from the Firmware Application can be used to monitor connection status.
Device Configurations
Device configuration options exist:
-Index 0: VISCA over IP/Serial
-If “1” = VISCA over Serial
Example:
Enabling VISCA over serial could look like this device configuration code: “D0:0=1” where the general
form would be “Dx:y=z” where “x” is the number of the device core as installed on the controller (starting
with zero for the first device core), “y” the index number and “z” the value for that index.
If the Sony SRG-300 Device Core is the first like below:
Setting VISCA over serial would be set by this configuration under “Manage Media” on the configuration
page for your controller. Access this by pressing “Online Configuration” in the Firmware Application.
Remember to save on the configuration page and press “Check for updates” in the Firmware Application.
2
SKAARHOJ DEVICE CORES
To confirm that a device configuration is in fact detected by the controller, please check it out on the serial
monitor where it will be mentioned:
Dip Switches
There are multiple dip switches on the bottom of the Sony SRG-300 to control connection via IP or Serial.
3
Switch
LAN
VISCA
1
On
Off
2
Off
Off
3
Off
Off
4
Off
Off
5-8
Off
Off
SKAARHOJ DEVICE CORES
Ethernet to Serial connection
To communicate via serial (RS-232C) to the Sony SRG-300 camera you need an Ethernet-Serial converter.
We suggest you get a USR-TCP232-306 from USR IOT - https://www.pusr.com/products/ethernet-to-serial-
converters-usr-tcp232-306.html
Below you will find screenshots of how to configure the USR-TCP232-306 converter (found of the web
interface of the USR-TCP232-306). Notice the IP address of the USR-TCP232-306 (Static IP Address) must
match the IP settings of the SRG-300 Device Core.
In the settings below the Baud Rate is set to 9600 and Serial Type to RS232. The camera must match these
settings.
Actions
An excerpt of the actions in the Device Core
4
Table of contents
Other Sony Security Camera manuals
Sony
Sony SNC-DH110T User manual
Sony
Sony DXC-930 User manual
Sony
Sony SNC-VM600 User manual
Sony
Sony SSC-CB564R User manual
Sony
Sony SNCVM601 User manual
Sony
Sony CD-1453 User manual
Sony
Sony EM100 User manual
Sony
Sony IPELA SNC-VM772R User manual
Sony
Sony IPELA SNC-CH110 User manual
Sony
Sony HD 3CCD COLOR BRC-H700 Installation manual
Sony
Sony Ipela SNC-ER585 User manual
Sony
Sony 700TVL User manual
Sony
Sony SSC-N24A User manual
Sony
Sony SNC-RZ25N - Network Camera User manual
Sony
Sony XC-555 User manual
Sony
Sony XC-003 User manual
Sony
Sony Ipela SNC-EP520 User manual
Sony
Sony Network Video Monitoring User manual
Sony
Sony SNCVB600 User manual
Sony
Sony CD39IR-4N1S User manual
