Sony SNC-xx Quick start guide

Easy Setup Guide

for the Sony Network

Camera



Please read the information with this mark attached

carefully.

3-878-191-11 (1)

For setup, a computer running the Microsoft Windows Operating

System is required.

For monitoring camera images, Microsoft Internet Explorer (Version

6.0 or later) is required.

This section describes the operation to be followed to conrm the

required settings using Windows Vista as an example. Thus, the

screens in this manual may be different from the screens of your

computer, depending on the OS you are using.

Microsoft, and Windows are registered trademarks of Microsoft Corporation in the

United States and/or in other countries.

Network camera

Hub (or router)

Computer

Before Using Your Camera For

the First Time

This “Easy Setup Guide for the Sony Network Camera” describes how to monitor

images from your Sony network camera on a computer connected to the same

network.

First, conrm that the camera and computer are properly connected to the same

network via a hub or router, as illustrated below.

• For detailed information on how to connect the hub (or router) and the computer,

refer to the instruction manuals supplied with the hub (or router) and the computer.

• For detailed information on how to connect the hub (or router) and the camera, refer

to the Installation Manual supplied with your camera.

Sequence of the Easy Setting

Operation

This setup guide describes how to make the required settings in the following order so

that you can monitor images from your camera on your computer.

1Conrming the Settings of

the Computer

This section describes how to conrm the settings of the computer.



2Setting the IP Address of the

Camera

This section describes how to set the IP address of the camera so that

you can access the camera from the computer.

3Monitoring Images from the

Camera

This section describes how to monitor the camera images on the

computer.



1Conrming the Settings of

the Computer

1Turn on the computer and

start Windows.



Log on as an Administrator. 2Click the [Start] button and then click

[Control Panel].

3When the “Control Panel” window

appears, click [View network status

and tasks] in [Network and Internet].

4When the “Network and Sharing

Center” window appears, click

[View status].



When [Status] is not active, make sure that the

network cable is connected to a computer and

hub.

5When [Local Area Connection Status] is displayed,

click [Details…].

When using Windows XP

“Address Type” can be displayed by the following steps for steps 3 to 5.

Select [All Programs], [Accessories], [Communications], [Network Connections] from the [Start] menu.



When [Network Connections] is displayed, double-click [Local Area Connection].



When [Local Area Connection Status] is displayed, double-click [Support].

1Conrming the Settings

of the Computer

“DHCP Enabled No”

is displayed.

When using Windows XP

“Manually Congured”

is displayed in the [Local Area

Connection Status].



Go to step 7-a. (Page 7)

“DHCP Enabled Yes”

is displayed.

When using Windows XP

“Assigned by DHCP”

is displayed in the [Local Area

Connection Status].



You need do nothing else here.

Close any windows opened

in step 2 or later, and go to

2Setting the IP Address

of the Camera .

(Page 11)

6When [Network Connection Details] is displayed,

check the DHCP status.

1Conrming the Settings

of the Computer

Place a check mark in the following box corresponding to

the type of address in the “Address Type” box.

Be sure to conrm the type of address displayed here,

because the operations required in future setting

procedures are different, depending on the type of

address.

1Conrming the Settings

of the Computer

7-a Conrm the IP Address, Subnet Mask, and

Default Gateway at step4.

IPAddress

...

 

Subnet Mask

...



Default Gateway

...





The Default Gateway may not be displayed, depending on the network

environment. In this case, leave the boxes for Default Gateway blank.

Items to are required in future setting

operations.

Write these values in the respective boxes in

advance so that you will be able to refer to these

values.

Go to step 7-b to change IP address. (You do not

usually need to change this address.)

Go to

2Setting the IP Address

of the Camera .

(Page 11)

1Conrming the Settings

of the Computer

7-bTo change the IP address other than the IP address

shown in step 4, follow the steps shown below.

1Select [Network and Internet], [View network

status and tasks] in [Control Panel] from the

[Start] menu.

2Click [View status].

3When [Local Area Connection Status] is

displayed, click [Properties].

If the message “User Account Control –

Windows needs your permission to continue”

appears, click [Continue].

1Conrming the Settings

of the Computer

4Click the [General] tab, place a check mark

in the [Internet Protocol Version4 (TCP/IPv4)]

box, and then click [Properties].

If a check mark has already been placed in

the [Internet Protocol Version4 (TCP/IPv4)]

checkbox, click on [Internet Protocol Version4

(TCP/IPv4)], and then click [Properties].



[Internet Protocol Version 4(TCP/IPv4)] and [Internet Protocol Version 6(TCP/IPv6)] are displayed in the item list. Be sure to

select [Internet Protocol Version 4(TCP/IPv4)].

When using Windows XP

Select [Internet Protocol Version (TCP/IP)].

5Select [Use the following IP address] and

type the following IP address and Subnet

mask in the appropriate boxes.

Example:

[IP address]

192.168.0.200

[Subnet mask]

255.0.0.0



You will use the IP address and Subnet mask again when

“Setting the IPAddress of the Camera.” (Page 11)

When there is a network administrator, ask for and obtain an IP

address from the network administrator. If not, you can obtain

an un-used IP address.

To obtain an un-used IP address, see “Conrming an IP

address that is not currently used in the network” (page 10).

Click the [Use the following IP address] radio button

and type the IP address and Subnet mask.

1Conrming the Settings

of the Computer

8The IP address of the

computer is set.

Go to

2Setting the IP Address

of the Camera .

(Page 11)

6 Conrm that [Use the following DNS server

addresses] is selected.

When you select [Use the following IP

address] in step 5, [Use the following DNS

server addresses] is selected automatically.

You do not need to enter the address in the

[Preferred DNS server] and [Alternate DNS

server] boxes.

Conrm this radio button is selected.

7Click [OK], and close any windows opened in

step 2or later.

Conrming an IP address that is not currently being used in the network

1Select [All Programs], [Accessories],

[Command Prompt] from the [Start] menu.

2When the “Command Prompt” window

appears, type “ping aaa.bbb.ccc.ddd”

representing the numbers you want to set

as the IP address of the camera in the

window described above. For example;

type “ping 192.168.0.100,” and then press

the [Enter] key on the keyboard.

3If “Request timed out.” appears in the

window, the IP address you entered is not

used in the network. (You can then use

those numbers as the IP address of the

camera.)

This manual suits for next models

Other Sony Security Camera manuals

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications