Socket DURASCAN D750 Manual

Choose 2Rent

Phone 1 (800) 622-6484

Fax 1 (866) 937-8254

info@choose2rent.com

www.choose2rent.com

page 1 of 6

1. Powering ON:

Press and hold down the small

power button until the LED turns

blue and the scanner beeps twice

2. Powering OFF:

Press and hold down

the small power

button until the

scanner beeps

twice.

1.Scanning

Barcodes

After connecting the scanner to your device,

open an application. Put the cursor where you

want to enter data. Hold the scanner about 4

inches from the barcode and press and hold the

trigger button. Keep your hand steady and make

sure the red beam covers the entire width of the

barcode.

By default, the scanner will beep and vibrate, and the LED will flash

green to confirm that data was decoded and sent to the host device.

2. Simultaneous Scanning and Soft Keyboard Support

The Scanner supports simultaneous use of the barcode scanner and the

Apple iOS on-screen keyboard while entering data into an application.

To open or close the onscreen keyboard, quickly double press the power

button (like double-clicking a mouse).

After you double-press the power button, the scanner will beep to

indicate that the onscreen keyboard was enabled/disabled.

Watch a video: http://www.youtube.com/watch?v=VhtttoC6ROs

Socket Mobile D750 Setup

page 2 of 6

3. Pair the Scanner with the Apple device:

-Power on the Scanner

-Make sure the scanner is set to HID Keyboard mode (default). If

needed you can switch to iOS Mode (explained on page 3).

-Enable Bluetooth on the Apple device. Search for Bluetooth devices

-In the list of found devices, select Socket CHS [xxxxxx]. If prompted,

tap Pair.

4. Unpairing the scanner from your iPad or iPhone

Power on the scanner. Press and hold the TRIGGER

and the POWER button together. After you hear 3

beeps, release both buttons. The scanner will unpair

and power off.

5. Mounting the Scanner with the QX Stand

When charging the scanner, make sure the

charging pins on the stand and the scanner

make contact with each other and the red LED

on the stand is illuminated. When fastened on

the magnet, the Scanner will enable the sensor

to automatically react to motion and scan any

item.

page 3 of 6

page 4 of 6

•Pair and connect the D750 to your device prior to placing the scanner

in Auto Mode. The Scanner is not discoverable when in Auto Mode and

in the Stand. This facilitates a fast connection to the current connected

device when powered on (for example the start of the new business

day).

•The Trigger button must be pressed to disable Presentation Mode (and

enable Mobile Mode) after the scanner is removed from the Stand.

•The Scanner will not turn off when it’s in Presentation Mode and in the

Stand under AC Power.

•To avoid excessive power drain, the scanner should not be left out of

the Stand in Auto Mode. Either press the Trigger button or Power off

the scanner.

6. BEEP and Vibration Settings

For full instructions visit:

https://socketwebcdn.blob.core.windows.net/cdn/docs/default-source/700-

series/durascan/ug_d750.pdf?sfvrsn=c1a183cb_9

page 5 of 6

HID MODE Keyboard Pop-up

Enable

The scanner emulates the keyboard

in HID mode. So scanned barcode

data will be input into the text field.

The following steps show how to

access the onscreen keyboard while

connected to the scanner in HID

mode.

(Best used for Windows & Android)

1. Make sure the scanner is

connected to your Apple device

in HID mode.

2. Open your application and place

the cursor where you want to

enter data.

3. Quickly double press the power

button of the Scanner (like

double-clicking a mouse) to

open or close the onscreen

keyboard. The scanner will beep

once as confirmation.

iOS MODE - SCANNER-ENABLED

APP

If you are using the scanner with an

iOS device and a Scanner-enabled

Application that does not provide

instructions to connect with the

scanner, please use the following

steps.

1. Power on the scanner and scan

this barcode. The scanner will

beep 3 times.

2. Turn Bluetooth on for the Apple

device. Go to Settings >

Bluetooth. A Bluetooth Devices

search will begin.

3. Tap Socket Mobile

D750[xxxxxx] in the list of

Devices found. After a few

seconds the “Not Paired” status

will change to “Connected” and

the scanner Blue LED will blink

every 3 seconds confirming the

connection.

page 6 of 6

Scan Tips

•Be sure to place the QR code 4-6 inches away from the

scanner and slowly back away the QR code till a beep sound

is made.

•Do not wave! Move in and out!

•If scanning a QR code on a mobile

device, be sure to have the device

brightness set to highest. (Especially

devices with privacy screens)

•Be sure to enlarge the QR code to a

reasonable size. You may experience

difficulty if the QR code is too small to

read.

•Cracked screens may cause difficulty

when scanning. Guest should print out

the QR code or ask for assistance from

the Guest Registration Administrator.

Please call our support team if you need assistance

setting up your rental devices

1(800) 622-6484

Other manuals for DURASCAN D750

Socket DURASCAN D750 Manual

Popular Barcode Reader manuals by other brands