SnowEx SP-7000 User manual
Assembly Instructions
© TrynEx International 2014
F51558 REV-A140905
1
CUSTOMER COPY
Madison Heights, Michigan 48071
800-SALTERS
www.snowexproducts.com
SP-7000
Serial No. 140410300001SP-7000 and higher
2 © TrynEx International 2014 F51558 REV-A140905
Introduction
These Installation Instructions have been designed to guide you while assembling and installing your SnowEx spreader. Follow these instruc-
tions with care to ensure performance and longevity.
Please read and understand the safety warnings associated with the assembly and installation of the spreader before beginning. In addition
the safety information in the these instructions, observe general safety guidelines to maintain your safety and the safety of those around you.
TORQUE CHART
Use this chart as a guide for tightening hardware.
Hand-tighten all fasteners until complete, then tighten to the recommended torque (unless
specied otherwise in these instructions).
TORQUE CHART FT-LB
Fastener Recommended
Torque (ft-lb)
1/4-20 6
5/16-18 13
3/8-16 23
7/16-14 35
1/2-13 55
9/16-12 80
5/8-11 110
3/4-10 200
7/8-9 320
1-8 480
SAFETY ALERT DEFINITION
This Safety Alert Symbol is used to pinpoint characteristics that, if not carefully followed, can create a safety hazard. When you
see this symbol in this manual or on the machine itself, BE ALERT – your safety and the safety of others is involved.
An accident will occur, resulting in Serious Injury or Death if the instructions are not followed.
An accident may occur, resulting in Serious Injury, perhaps Death, if the instructions are not followed.
An accident may occur, resulting in Minor or Moderate Injury if the instructions are not followed.
Important Information; Property or Equipment Damage may result if not followed.
3© TrynEx International 2014 F51558 REV-A140905
Assembly Instructions
STEP 1
Unpack the spreader; remove the axle, tires, tongue, and spinner drive from the pallet, set aside so the main spreader assembly is alone on
the pallet.
STEP 2
Open the Spinner Drive Box. Open and locate the hardware kits.
STEP 3
Remove the lag bolts holding the spreader to the pallet.
AXLE WHEELS TONGUE
SPINNER DRIVEMUD FLAPFENDERS
BATTERY
4 © TrynEx International 2014 F51558 REV-A140905
Assembly Instructions
STEP 4
Lift the spreader and support it to allow installation of the axle and trailer tongue. Once lifted, remove and discard the pallet. As a safeguard,
in addition to the support jacks underneath the spreader, leave the lifting device in place.
STEP 5
Fasten the Axle to the frame.
STEP 6
Mount the wheels, tighten the lug nuts.
STEP 7
Attach the tongue. It bolts directly to the frame and to the hitch mount at the front of the trailer. Connect the leads of the trailer harness to the
control board: Red to “BAT +” and Black to “GROUND”. Put the Hitch Pin and Hair Pin through the clevis.
5© TrynEx International 2014 F51558 REV-A140905
STEP 9
Lower the tongue jack; pin in the vertical position. Remove the supports. Lower the spreader to rest on the tongue jack and the wheels.
STEP 10
Mount the fenders over the wheels.
STEP 11
Attach the ‘mud ap’ to the rear of the fenders. Use the clamp plate on the outside of the mud ap.
Assembly Instructions
STEP 12
Attach the spinner drive: lower the drive onto the pegs at the rear of the frame; secure with the two bolts and nuts from the hardware kit
through the hanger bracket. Plug it into the spinner plug on the side of the frame. Slide the spinner assembly’s hub over the motor shaft and
tighten the two bolts onto the ‘at’ of the shaft.
6 © TrynEx International 2014 F51558 REV-A140905
STEP 13
Install and connect batteries (under cover). Batteries are not included with the spreader. Use the long wires from T30725 to connect the
batteries to each other. Use the short wires to connect to the control board: Red to “BAT +” and Black to “GROUND”. Install the cover when
nished.
STEP 14
Fit Weather Cover over the top of the hopper.
FINISHED
Owner must supply
the batteries. They are
not included with the
spreader.
Assembly Instructions
7© TrynEx International 2014 F51558 REV-A140905
STEP 1
Determine the location of the vehicle’s battery.
STEP 2
Mount the breaker within 12 inches of the battery’s positive terminal.
STEP 4
Connect the negative lead of the harness to the negative terminal of the battery and the positive harness lead to the “AUX” terminal on the
breaker.
STEP 5
Tie the harness to the frame and other harnesses, working from the hitch area to the battery. Keep away from high-temperature and moving
components. Leave the end by the hitch loose so the harness can connect to the plug on the trailer tongue.
STEP 6
Connect the breaker wire to the positive terminal of the battery and the “BAT” terminal of the breaker.
STEP 7
Connect the spreader. Test that the spinner, auger, and vibrator work.
STEP 3
Route the harness from the rear of the vehicle, near the drawbar, to the battery. Leave enough harness free near the hitch to allow connect-
ing to the trailer tongue plug. Keep away from high-temp and moving components
Vehicle Wiring Instructions
View of Battery, Breaker,
Breaker Wire, and
Harness.
FINISHED
8 © TrynEx International 2014 F51558 REV-A140905
Notes
9© TrynEx International 2014 F51558 REV-A140905
Notes
10 © TrynEx International 2014 F51558 REV-A140905
Notes
Table of contents
Other SnowEx Spreader manuals
SnowEx
SnowEx V-Maxx G2 VX-6010 User manual
SnowEx
SnowEx Sidewalk-Pro SD-95 User manual
SnowEx
SnowEx HELIXX User manual
SnowEx
SnowEx SP-1675 User manual
SnowEx
SnowEx SP-575V Owner's manual
SnowEx
SnowEx V-Maxx G2 User manual
SnowEx
SnowEx V-Pro 32300 User manual
SnowEx
SnowEx SP-225-1 Operating instructions
SnowEx
SnowEx Super Maxx SP-9300XH Operating instructions
SnowEx
SnowEx 7500 User manual
SnowEx
SnowEx SP-9300 User manual
SnowEx
SnowEx SP-85 Owner's manual
SnowEx
SnowEx V-Pro 32300 User manual
SnowEx
SnowEx SP-3000 User manual
SnowEx
SnowEx SP-85 Operating instructions
SnowEx
SnowEx SP-7550 Owner's manual
SnowEx
SnowEx Tailgate Pro 575X User manual
SnowEx
SnowEx HELIXX User manual
SnowEx
SnowEx Drop Pro 600 User manual
SnowEx
SnowEx HELIXX Series User manual
Popular Spreader manuals by other brands
Fisher
Fisher POLY-CASTER 78601 owner's manual
TurfEx
TurfEx RS7200 Owner's/operator's manual
Ferris
Ferris Pathfinder Series Operator's manual
Fayat Group
Fayat Group DYNAPAC S100 operation & maintenance
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Operator's manual & parts list
EASTMAN
EASTMAN CR 500 instruction manual
