Smeg CS19ID-5 User guide

Index

1. PRECAUTIONS FOR SAFETY AND USE_____________________ 36

2. INSTALLING THE APPLIANCE _____________________________ 38

3. DESCRIPTION OF CONTROLS ____________________________ 40

4. HOB __________________________________________________ 47

5. USING THE OVEN_______________________________________ 52

6. ACCESSORIES AVAILABLE _______________________________ 53

7. COOKING ADVICE ______________________________________ 54

8. CLEANING AND MAINTENANCE ___________________________ 62

9. EXTRAORDINARY MAINTENANCE _________________________ 65

INSTRUCTIONS FOR THE INSTALLER: these are intended for the

qualified engineer who is to install, commission and test the

appliance.

INSTRUCTIONS FOR THE USER: these provide recommendations for

use, a description of the controls and the correct procedures for

cleaning and maintaining the appliance.

Introduction

1. PRECAUTIONS FOR SAFETY AND USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD

CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE COOKER'S LIFE

CYCLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE

INSTRUCTIONS IT CONTAINS BEFORE USING THE COOKER.

INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN

COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS APPLIANCE IS

INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC

DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE IS BUILT TO

PROVIDE THE FOLLOWING FUNCTION: COOKING AND HEATING FOODS;

ALL OTHER USES ARE TO BE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN

THOSE STATED ABOVE.

NEVER LEAVE PACKAGING RESIDUES UNATTENDED IN THE HOME.

SEPARATE WASTE PACKAGING MATERIALS BY TYPE AND CONSIGN THEM

TO THE NEAREST SEPARATE DISPOSAL CENTRE.

THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH

ELECTRICAL SYSTEM SAFETY REGULATIONS.

THE PLUG TO BE CONNECTED TO THE POWER SUPPLY LEAD AND THE

RELATIVE SOCKET MUST BE OF THE SAME TYPE AND COMPLY WITH THE

RELEVANT REGULATIONS.

THE POWER SUPPLY SOCKET MUST BE ACCESSIBLE EVEN AFTER THE

APPLIANCE HAS BEEN BUILT-IN.

NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD

IMMEDIATELY AFTER INSTALLATION, CARRY OUT A QUICK TEST ON THE

APPLIANCE FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS

MANUAL. IF THE APPLIANCE FAILS TO OPERATE, DISCONNECT IT FROM

THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE

CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.

AFTER EACH USE OF THE HOB, ALWAYS CHECK THAT THE CONTROL

KNOBS ARE TURNED TO 0(OFF).

NEVER PLACE FLAMMABLE OBJECTS IN THE OVEN: IF IT SHOULD

ACCIDENTALLY BE SWITCHED ON, THIS MIGHT CAUSE A FIRE.

Introduction

THE NAMEPLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND

MARK IS IN A VISIBLE POSITION IN THE STORAGE COMPARTMENT.

THE NAMEPLATE MUST NEVER BE REMOVED.

THIS APPLIANCE MUST NEVER BE INSTALLED ON A STAND.

THE APPLIANCE BECOMES VERY HOT DURING USE. TAKE CARE NOT TO

TOUCH THE HEATING ELEMENTS INSIDE THE OVEN.

NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT

AND SMOOTH ON THE HOB.

NEVER USE THE HOB AS A WORK-TOP.

WARNING: IF YOU NOTICE A CRACK IN THE CERAMIC HOB, DISCONNECT

THE APPLIANCE FROM THE ELECTRICITY SUPPLY AND CONTACT A

SERVICE CENTRE.

THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE (INCLUDING

CHILDREN) OF REDUCED PHYSICAL AND MENTAL ABILITY, OR LACKING IN

EXPERIENCE IN THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY

ARE SUPERVISED OR INSTRUCTED BY ADULTS OR PEOPLE

RESPONSIBLE FOR THEIR SAFETY.

THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC

ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE).

THIS DIRECTIVE CONTAINS THE REGULATIONS GOVERNING THE

COLLECTION AND RECYCLING OF DECOMMISSIONED APPLIANCES

THROUGHOUT THE EUROPEAN UNION.

BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND

PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.

The manufacturer declines all responsibility for injury or damage

caused by failure to comply with the above regulations or deriving from

tampering with even just one part of the appliance and the use of non-

original spare parts.

Instructions for the Installer

2. INSTALLINGTHE APPLIANCE

This appliance has fire protection (type Y) and can be installed against

walls higher than the work surface.

In compliance with Electromagnetic Compatibility regulations, the

electromagnetic induction hob is classified in Group 2 and Class B (EN

55011)

2.1 Electrical connection

Check that the voltage and size of the power supply line are as specified

on the nameplate inside the storage compartment. This nameplate

must never be removed.

The appliance's power supply line must be fitted with an omnipolar

breaking device with contact gap of at least 3 mm, located in an easily

accessible position close to the appliance itself.

The appliance has a terminal board on its rear for the electrical

connection (see diagram below). To access it, remove the back cover.

Instructions for the Installer

Operation at 380-415V3N~: use a H05RR-

F five-wire cable (cable of 5 x 2.5 mm2).

Operation at 380-415V2N~: use a H05RR-

F four-wire cable (cable of 4 x 4 mm2).

Operation at 220-240 V~: use a H05RR-F /

H05RNF three-wire cable (cable of 3 x 6

mm2).

The earth wire (yellow-green) must be at

least 20 mm longer than the other wires at

the end for connection to the appliance.

The power supply cable must be fitted with a suitable five-pin plug (see

technical data plate) or, for appliances operating on 220-240V∼, a three-

pin plug. The power supply plug and wall socket must be of the same

type (in compliance with CEI standards). The appliance must be earthed

appropriately. Before connecting it, check that the power supply line is

properly earthed. The use of reductions, adapters or junctions is not

recommended.

The manufacturer declines all responsibility for injury or damage

caused by failure to comply with the above regulations or deriving from

tampering with even just one part of the appliance.

2.2 Levelling

Level the appliance by means of its four adjustable feet. To make the

adjustment, undo the lock-nut and unscrew the foot. The adjuster screw

travel is 10 mm.

Instructions for the User

3. DESCRIPTION OF CONTROLS

3.1 The front panel

All the cooker's control and monitoring devices are placed together on the

front panel.

At first use after a power blackout, press the middle knob for 1 - 2

seconds to enable oven cooking operations.

KEY TO SYMBOLS

OVEN THERMOSTAT

CENTRAL

COOKING ZONE

OVEN FUNCTIONS

RIGHT REAR

COOKING ZONE

LEFT FRONT

COOKING ZONE

RIGHT FRONT

COOKING ZONE

LEFT REAR

COOKING ZONE

THERMOSTAT KNOB

The cooking temperature is selected by turning the knob

clockwise to the required setting, between 50° and 250°C.

The light comes on to indicate that the oven is heating up.

This light goes out when the set temperature is reached.

When it flashes at regular intervals, the temperature inside

the oven is being kept constantly at the set level.

Instructions for the User

FUNCTION SELECTOR KNOB

Turn the knob to select one of the following functions:

NO FUNCTION SET BOTTOM HEATING

ELEMENT + FAN

TOP AND BOTTOM HEATING

ELEMENTS

BOTTOM HEATING

ELEMENT + FAN HEATING

ELEMENT

TOP AND BOTTOM HEATING

ELEMENTS + FAN FUNCTION

FAN HEATING ELEMENT +

FAN

GRILL ELEMENT DEFROSTING

GRILL ELEMENT + FAN

HOB CONTROL KNOB

These knobs provide control of the ceramic hob's

cooking zones.

The zone it controls is shown above each knob. The

knob shown on the right is for the rear left-hand

cooking zone.

Turn the knob to the right to set the zone's operating

power; the settings range from a minimum of 1 to a

maximum of 9.

The working power is shown by a display on the hob.

Instructions for the User

Heating accelerator

Each cooking zone is equipped with a heating accelerator.

This system allows the zone to be operated at peak power for a time

proportional to the heating power selected.

To start the heating accelerator, turn the knob to the left, select setting

“A” and then release. The letter “A” will appear on the display on the

hob.

You now have 3 seconds to select the heating setting of your choice.

Once a setting between 1 and 9 has been selected, “A” and the chosen

setting will flash in alternation on the display.

While the heating accelerator is in operation, the heating level can be

increased at any time. The "full power" time will be modified accordingly.

If the power is reduced by turning the knob anticlockwise, option "A" is

automatically deactivated.

Power Function

The power function allows the user to operate each heating zone

continuously at the maximum power for a time of no more than 10

minutes. This function can be used, for example, to bring a large amount

of water to the boil in a hurry, or to turn up the heat under meat.

Turn the knob clockwise and set heating level 9, then use the knob to set

the "P" position and release it. "P" appears on the corresponding zone

display.

After 10 minutes, the power is reduced automatically, the knob returns to

the 9 setting and the "P" disappears.

However, the power function can be turned off at any time by reducing

the heating level.

When the power function is selected for one heating zone (e.g. the left

front zone), the power absorbed by the second zone (left rear zone)

might be reduced to supply the maximum available energy to the first

zone.

Consequently, the power function takes priority over the heating

accelerator.

If a pan is removed from the cooking zone while the power function is on,

the function is switched off.

Instructions for the User

3.2 Electronic Analogue Clock (on some models only)

LIST OF FUNCTIONS

MINUTE-MINDER BUTTON

END OF COOKING BUTTON

CLOCK TIME ADJUSTMENT AND RESET

VALUE DECREASE BUTTON

VALUE INCREASE BUTTON

3.2.1 Setting the time

When the oven is used for the first time, or after an interruption in the

electricity supply, the display flashes at regular intervals. Press the

key for 1 / 2 seconds to stop the display flashing and start the procedure

for setting the current time. Press the value modification keys or to

increase or decrease the setting by one minute for each pressure.

Press one of the two value modification keys until the current time

appears. 6/7 seconds after the last key is pressed, the clock will start

from the time set.

At the end of each programmed operation 8 beeps will sound 3/4 times

at intervals of about 1 and a half minutes. This sequence can be stopped

at any time by pressing any key.

Instructions for the User

3.2.2 Minute-Minder

-This function does not stop cooking; it simply

activates the buzzer. Press the key and the

display will light up as shown in figure 1;

-Within 6/7 seconds, press the or keys to

set the minute-minder. Each time a key is

pressed, 1 outside segment, representing 1

minute of cooking time, will light up or go out.

(figure 2 shows a cooking time of 10 minutes).

-6/7 seconds after the last key is pressed, the

countdown will start; when it finishes, the

buzzer will sound.

-During the countdown, the current time can be

viewed by pressing the key once; press it

again to return to the minute minder display.

-At the end of the countdown, the oven must

be switched off manually by turning the

thermostat and function selector knob to 0.

Table of contents

Popular Cooker manuals by other brands

Modena

Modena FC 7645 SGM User manual book

Electrolux

Electrolux Insight EKG6049 user manual

Stanley

Stanley Donard 60 Installation and operating instructions

Bartscher

Bartscher 201TC manual

Parkinson Cowan

Parkinson Cowan 50 GR/BU installation instructions

Siemens

Siemens HK9P00020U instruction manual

Creda

Creda S150E Installation and user instructions

Creda

Creda HB48309 instructions

Bosch

Bosch HCE743220F instruction manual

Tricity Bendix

Tricity Bendix SE545P manual

NEFF

NEFF E1461A2/01 Instructions for use

Zanussi

Zanussi ZCM 700 X Instruction booklet

RiverGrille

RiverGrille TF2002501-RG Assembly instruction

Vollrath

Vollrath 69504F Operator's manual

Tricity Bendix

Tricity Bendix CSIE500 Operating and installation instructions

AEG

AEG Competence 5731 V Instruction book

Euromaid

Euromaid ES60 Installation and operation manual

Hotpoint

Hotpoint HUI 62 TP Instructions for installation and use