SLE Water Bottle Camera User manual
1 Version
1.4
Secure Law Enforcement
Water Bottle Camera
2 Version 1.4
Thank you for purchasing our Secure Law
Enforcement Camera
Please read this manual before operating the camera
and keep it handy.
Your purchase should include:
1 x OmniBottle
1 x AC Wall Charger
1 x MicroUSB Cable
1 x Manual
1 x A/V Cable
1 x 3.5mm to USB Cable
1 x Remote
1 x 16GB MicroSD Card
1 x MicroSD Card Reader
1 x Charging Adapter with Indicator
Lights
3 Version 1.4
GET FAMILIAR WITH YOUR OMNIBOTTLE HIDDEN
CAMERA
4 Version 1.4
5 Version 1.4
6 Version 1.4
Charging your Camera
1. First, you can connect the provided charging
cable to the battery charging port on the 3D
printed housing inside the bottle. The LED
indicator light will be on as long as the cable is
connected. We recommend charging for 4-6
hours to get a full charge.
2. Secondly, you may remove the battery from the
housing, disconnect the battery connection and
then use the matching charging connector and
wall jack that was provided in your box to
charge the battery via a wall outlet (see page
5). While charging, there will be a red indicator
7 Version 1.4
light, and when the battery is fully charged the
light will become blue.
OPERATING THE CAMERA
HOW TO TURN ON THE CAMERA
1. Your device can be powered on in one of two
ways.
a. Connect your device to an AC outlet
using the provided AC wall charger.
b. Use the internal battery to power the
device (please see previous page for
charging instructions).
2. If you plug the device into an electrical outlet,
the device will power on automatically and
enter into motion detection mode. The Green
light will blink once and then the Red light will
blink 3 more times and turn off (if motion is
detected immediately). The device is now in
motion detection mode.
3. If you choose to use battery power, point the
remote at the device and press the power
8 Version 1.4
button on the remote (see page 4). The Green
light will blink once and then the Red light will
blink 3 more times and turn off (if motion is
detected immediately). The device is now in
motion detection mode.
NOTE: If the light doesn’t come on, try many different
angles when pressing the power button and pointing it
at the front/top of the unit. Do not hold down the power
button. Press and release the button only.
4. To put the device into standby mode, stop
motion recording by pressing the motion
detection button one time. The Green light will
come on, and the device will be in standby
mode.
HOW TO RECORD VIDEO
1. When the camera is in Standby Mode, press the
“Continuous Recording Button.” (see page 4)
The Indicator LED will flash two times.
9 Version 1.4
2. Once the Indicator LED turns off, the camera is
now recording video.
HOW TO STOP RECORDING VIDEO
1. While the camera is recording video, press the
“Continuous Recording Button” once more.
(The Indicator LED will turn on.)
2. The camera has now stopped recording and is
now in Standby Mode.
HOW TO TAKE PICTURES
1. When the camera is in Standby Mode, press the
“Photo Button” (see page 4). The green light
will turn red while the photo is being taken.
2. Once the photo is taken, the light will turn back
to green and once again be in standby mode.
HOW TO RECORD MOTION DETECTION
1. When the camera is in Standby Mode, press the
“Motion Detection Button” (see page 4).
2. If motion is detected, the Red light will flash 2
times and turn off.
10 Version 1.4
3. If there is no motion after 1 minute, the device
will return to detection standby mode until
motion is detected again. While waiting, the
Green light will be on.
NOTE: If you activate motion detection and there is no
motion currently in front of the camera, there will be no
indication you have entered into motion mode. The green
light will simply remain on. If you wish to confirm that
you have entered into motion detection mode, wave your
hand in front of the camera lens, and the unit will flash
the red light 2 times. Then the light will turn off
confirming that the device detected your motion and is
now recording video.
HOW TO STOP RECORDING MOTION DETECTION
1. While the camera is recording motion
detection, press the “Motion Detection Button”
once more. (The Indicator LED will turn on.)
2. The camera has stopped recording motion
detection and is now in Standby Mode.
Table of contents
