Sinclair MC-F09AI User manual
USER'S MANUAL
MULTI COMBI SERIES
FLOOR&CEILING MC-F09,12,18,24AI
User Notice
◆When operating, the entire capacity of the cooperating indoor unit should be not larger than
150% of outdoor unit. Otherwise, it will cause the shortage of cooling (heating) capacity.
◆The power supply of the entire unit must be the power supply of outdoor unit. And
disconnect the main power of outdoor units before cleaning.
◆In order to turn on the units successfully, the main power switch should be opened 8 hours
before the operation.
◆After receiving the turn off signal, every indoor unit will continue to work for 20-70sec to
make use of the rest cool air or the rest heat air in the heat exchanger, while preparing for the next
operation. And this is normal.
◆When the selected operating mode of the indoor unit are clash with the operating mode of
the outdoor unit, the malfunction light will blink after 5s on the indoor unit or remote controller
showing that the operation clash, then the indoor unit will stop. At this time, change the operation
mode of the indoor unit to the one that would not clash with the outdoor operating mode to make
the operation normal. The cooling mode is not clash with the dry mode, while the fan mode is not
clash with any mode.
◆The appliance shall not be installed in the laundry .The appliance shall not be used by
children without supervisor.
◆An all-pole disconnection switch having a contact separation of at least 3mm in all poles
should be connected in xed wiring.
◆Missing information regarding electric supply tolerances(+/-10%, +/-1Hz) in
documentation.
◆Humidity range: 30%~95%.
◆Main switch provided by end user: main switch handle should be black or gray, it can be
locked in “OFF” position with padlock.
◆The main disconnection device should be installed at a height of 0.6~1.7m. over current
protection is required(EN 60947-3, EN 60947-2).
◆The cooling range of the unit is the outdoor environment temp.-5~48 ℃DB, the heating
range of the unit( only for the heat pump type unit) is the outdoor environment temp. -15~27 ℃
DB.
This product must not be disposed together with the domestic waste. This product
has to be disposed at an authorized place for recycling of electrical and electronic
appliances.
Thank you for your selecting of Sinclair air conditioner, please read this usage and install
instruction carefully and keep it well in order to use this unit correctly.
Wired Controller XK19
1
ⅠWired Controller XK19
1 Wired Controller XK19
It is optional for the cassette type, wall-mounted, and oor ceiling indoor units.
1.1 Outside View of the Wired Controller
Fig.1 Outside View of the Wired Controller
1.2 LCD of the Wired Controller
Fig.2 LCD of the Wired Controller
Wired Controller XK19
2
1.3 Introduction to the Symbols on LCD
Table 1
No. Symbols Description
1Swing function.
2Sleep function (3 types: sleep 1,sleep2 and sleep 3).
3Running modes of the indoor unit (Cooling, Dry, Fan and Heating).
4Defrosting function for the outdoor unit.
5Gate-control function (this function is yet unavailable for this unit).
6Lock function.
7High, middle, low or auto fan speed of the indoor unit.
8 SHIELD Shield functions (buttons, temperature, On/Off, Mode or Save is shielded or
Save is shielded by the remote monitor.
9 TURBO Turbo function.
10 MEMORY Memory function (The indoor unit resumes the original setting state after
power failure and then power recovery).
11 MASTER Master wired controller (this function is yet unavailable for this unit).
12 It blinks under on state of the unit without operation of any button.
13 SAVE Energy-saving function.
14 Ambient/preset temperature value.
15 E-HEATER Electric auxiliary heating function.
16 BLOW Blow function.
17 Timing value.
18 QUITE Quiet function (two types: quiet and auto quiet).
19 SET It will be displayed under the debugging mode.
2 Buttons
2.1 Buttons on the Wired Controller
Fig. 3 Buttons on the Wired Controller
Wired Controller XK19
3
2.2 Function of the Buttons
Table 2
No. Name Function
1 Enter/cancel ① Function selection and cancellation.
② Press it for 5s to examine the outdoor ambient temperature.
2▲① Running temperature setting of the indoor unit, range:16 ～30℃ .
② Timer setting, range:0.5-24 hr.
③ Switchover between quiet/auto quiet or among sleep1/sleep2/sleep 3.
6▼
3 Fan Setting of the high/middle/low/auto fan speed.
4 Mode Setting of the Cooling/Heating/Fan/Dry mode of the indoor unit.
5 Function Switchover among the functions of Swing/Sleep/Turbo/Save/E-heater/Blow /
Quiet etc.
7 Timer Timer setting.
8 On/Off Turn on/off the indoor unit.
4+2 ▲+Mode
Press them for 5s under off state of the unit to enter/cancel the Memory function
(If memory is set, indoor unit after power failure and then power recovery will
resume the original setting state. If not, the indoor unit is defaulted to be off after
power recovery. Memory off is default before delivery.).
3 +6 Fan+▼
By pressing them at the same time under off state of the unit, will be displayed
on the wired controller for the cooling only unit, while will be displayed on
the wired controller for the cooling and heating unit.
2 +6 ▲+▼
Upon startup of the unit without malfunction or under off state of the unit,press
them at the same time for 5s to enter the lock state, in which case, any other
buttons won’t respond the press. Repress them for 5s to quit this state.
3 Operation Instructions
3.1 On/Off
Press On/Off to turn on the unit and turn it off by another press.
Note: The state shown in Fig.4 indicates the “Off” state of the unit after power on. The state shown in
Fig.5 indicates the “On” state of the unit after power on.
Fig. 4 “Off” State Fig. 5 “On” State
3.2 Mode Setting
Under the “On” state of the unit, press Mode to switch the operation modes as the following sequence:
Cooling-Dry-Fan-Heating.
Wired Controller XK19
4
3.3 Temperature Setting
Press ▲or ▼ to increase/decrease the preset temperature. If press either of them continuously, the
temperature will be increased or decreased by 1℃every 0.5s,as shown in Fig.6.
In the Cooling, Dry or Heating mode, the temperature setting range is 16℃～ 30℃ .
In the Fan mode, the setting temperature is xed at 26℃.
In the Auto mode, the setting temperature is unadjustable.
Fig.6
3.4 Fan Setting
Under the “On”/”Off” state of the unit, press Fan and then fan speed of the indoor unit will change
circularly as shown in Fig.7.
Fig.7
3.5 Timer Setting
Under the “On”/”Off” state of the unit, press Timer to set timer off/on.
Timer on setting: press Timer, and then LCD will display “xx.x hour”, with “hour” blinking. In this case,
press ▲or ▼ to adjust the timing value. Then press Enter/cancel to conrm the setting.
Timer off setting: press Timer, if LCD won’t display xx.x hour, and then it means the timer setting is
canceled.
Auto Low Middle High
Wired Controller XK19
5
Timer off setting under the “On” state of the unit is shown as Fig.8.
Fig. 8 Timer off Setting under the “On” State of the Unit
Timer range: 0.5-24hr. Every press of ▲or ▼ will make the set time increased or decreased by 0.5hr. If
either of them is pressed continuously, the set time will increase/ decrease by 0.5hr every 0.5s.
3.6 Swing Setting
Swing On: Press Function under on state of the unit to activate the swing function. In this case, will
blink. After that, press Enter/cancel to make a conrmation.
Swing Off: When the Swing function is on, press Function to enter the Swing setting interface, with
blinking. After that, press Enter/cancel to cancel this function.
Swing setting is shown as Fig.9.
Wired Controller XK19
6
Fig. 9 Swing Setting
Note:
① .
Sleep, Save, Turbo, Blow or Quiet setting is the same as the Swing setting.
② .
After the setting has been done, it has to press the key “Enter/cancel” to back to the setting status or
quit automatically ve seconds later.
3.7 Sleep Setting
Sleep on: Press Function under on state of the unit till the unit enters the Sleep setting interface. Then
press ▲or ▼ to switch among Sleep 1, Sleep 2 and Sleep 3. After that, press Enter/cancel to conrm the
setting.
Sleep off: When the Sleep function is activated, press Function to enter the Sleep setting interface. After
that, press Enter/cancel to can this function.
Sleep setting is shown as Fig.10.
Wired Controller XK19
7
Fig. 10 Sleep Setting
Sleep off is default after power failure and then power recovery, and the sleep functions is unavailable
under the fan mode.
There are three Sleep modes: Sleep 1, Sleep 2 and Sleep 3.
a. Sleep 1
In the Cooling or Dry mode, the temperature will increase by 1℃after the unit runs under Sleep 1 for 1hr
and 1℃after another 1hr.After that, the unit will run at this temperature.
In the Heating mode, the temperature will decrease by 1℃after the unit runs under Sleep 1 for 1hr and
1℃after another 1hr. After that, the unit will run at this temperature.
b. Sleep 2
In the Cooling mode, the temperature may be set between 16 ℃-23 ℃, 24 ℃- 27 ℃or 28 ℃- 29 ℃
or at 30 ℃, and their Sleep curves are shown in Fig.11 (Note: The curve is only for reference, the actual
temperature is subject to the time point.).
For example: The temperature in the Cooling mode is set at 25 ℃. Under the mode of Sleep 2, the
temperature will increase by 1℃every 1hr. After it increases by 2℃in total, it will keep at 27℃. 7 hours
later, it will decrease by1℃, i.e. 26℃.After that, the unit will keep running at 26℃.
This manual suits for next models
3
Table of contents
Other Sinclair Air Conditioner manuals
Sinclair
Sinclair SDV6 Operating manual
Sinclair
Sinclair SF2 D3 Series Instruction Manual
Sinclair
Sinclair SF-F3 Series User manual
Sinclair
Sinclair ASC-XXAIN User manual
Sinclair
Sinclair ASH-09AIK User manual
Sinclair
Sinclair Focus Plus ASH-13BIF2 User manual
Sinclair
Sinclair ASE-76AH User manual
Sinclair
Sinclair SIH-09BIK User manual
Sinclair
Sinclair MS-H07AIC PT User manual
Sinclair
Sinclair Spectrum Series User manual
Sinclair
Sinclair ASC-18BI User manual
Sinclair
Sinclair ROCKY SERIES ASH-09AIR User manual
Sinclair
Sinclair AMC-14Aa MOBILE SERIES User manual
Sinclair
Sinclair ASH-09AIR2 User manual
Sinclair
Sinclair SF HM2 Series User manual
Sinclair
Sinclair SDV5 Series User manual
Sinclair
Sinclair ASGE BI-3 Series User manual
Sinclair
Sinclair SDV4 series User manual
Sinclair
Sinclair MC-C12AI User manual
Sinclair
Sinclair ASFU-09A User manual
Popular Air Conditioner manuals by other brands
Fujitsu
Fujitsu Inverter ASBA30JFC operating manual
Toshiba
Toshiba RAS-M10SMUV-E installation manual
Daikin
Daikin FXLQ20MAVE Operation manual
Hitachi
Hitachi RAS-E24CAK instruction manual
CIAT
CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance
Bestron
Bestron AAC6000 instruction manual
