Simplex 4606-9102 User manual

TYCO, SIMPLEX, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited. 579-977

Rev. C

Introduction The 4606-9102 Liquid Crystal Display (LCD) Annunciator for the 4010ES provides remote

annunciation of the Fire Alarm Control Unit (FACU) status, see Figure 1. Visual status is

provided using an LCD and LEDs. Audible annunciation is provided using a piezo sounder. Use

the keyswitch to lock or enable the annunciator switch.

Figure 1. 4606-9102 LCD Annunciator

In this

publication

FIRE

ALARM

PRIORITY 2

ALARM

SYSTEM

SUPERVISORY

SYSTEM

TROUBLE

POWER

ALARM

SILENCED

ALARM

ACK

ALARM

ACK

SUPV

ACK

TBL

ACK

ALARM

SILENCE

SYSTEM

RESET

DISPLAY

TIME

Topic Page

Specifications 2

Installing the 4606-9102 LCD Annunciator 2

Address chart 4

General wiring precautions 7

Specific wiring precaution 7

Wire length tables 7

Checkout procedure 8

Cautions

and warnings

READ AND SAVE THESE INSTRUCTIONS - Follow the instructions in this installation manual. These instructions

must be followed to avoid damage to this product and associated equipment. Product operation and reliability depend

upon proper installation.

DO NOT INSTALL ANY SIMPLEX® PRODUCT THAT APPEARS DAMAGED - Upon unpacking your

Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim

with the carrier and notify an authorized Simplex product supplier.

ELECTRICAL HAZARD - Disconnect electrical field power when making any internal adjustments or repairs. All

repairs should be performed by a representative or authorized agent of your local Simplex product supplier.

STATIC HAZARD - Static electricity can damage components. Handle as follows:

• Ground yourself before opening or installing components.

• Prior to installation, keep components wrapped in anti-static material at all times.

EYE SAFETY HAZARD -Under certain fiber optic application conditions, the optical output of this device may exceed

eye safety limits. Do not use magnification (such as a microscope or other focusing equipment) when viewing the output

of this device.

SULFURIC ACID WARNING -Battery contains sulfuric acid, which can cause severe burns to the skin and eyes and

can destroy fabric. Replace any leaking or damaged battery while wearing appropriate protective gear. If you come in

contact with sulfuric acid, immediately flush skin or eyes with water for 15 minutes and seek immediate medical attention.

4606-9102 for 4010ES LCD

Annunciator installation instructions

Specifications

• Communication wiring is supervised and power-limited.

• 24V power wiring supplied by a 4010ES FACU is power-limited.

• If the interconnected control unit is not used to provide operating power to the annunciator, a

regulated UL-listed 24VDC power supply for fire protective signaling is required.

• A minimum 18 AWG Twisted pair wiring is required for communications. If twisted-

shielded pair wire is used, ground the shield at the main panel only.

• Connect a dedicated earth ground connection to the back box, in accordance with NFPA 70,

Article 250.

Flush mount 4606-9102 LCD Annunciators

• In masonry walls, use a Steel City GW-635-G (3½ in/89mm deep) masonry box, or an

equivalent box.

• In plasterboard walls, use six listed gangable switch boxes, RACO 590 (3½ in/89mm deep),

RACO 600 (2½ in/63.5mm deep), RACO 601 (3½ in/89mm deep), or an equivalent box.

Surface mount 4606-9102 LCD Annunciators

• Use a 2975-9206 box (2¾ in/69.85mm deep) or a 2975-9217 box (1¾ in/44.75mm deep).

Installing the

4606-9102 LCD

Annunciator

Complete the following steps to install the 4606-9102 LCD Annunciator:

1. Terminate the annunciator’s communication (COMM) and power lines as shown in Figure 2.

Figure 2. Terminating the COMM and Power Lines

2. Connect the ground harness to earth ground.

Note: To prevent Electrostatic Discharge (ESD), use a wrist strap assembly that connects to ground. Ensure

the power is OFF before installing or servicing the annunciator.

Table 1: Power requirements and environmental limitations

Voltage 24VDC Power Supply. 24VDC Nominal/18VDC minimum.

Current Maximum Current Draw. with LCD Backlight OFF at 24VDC: 65mA.

Maximum Current Draw. with LCD Backlight ON at 24VDC: 110mA.

Maximum Current Draw. with LCD Backlight ON and Piezo ON at 18VDC: 140mA.

Temperature Operating Range. 32°F to 120°F (0°C to 49°C).

Humidity The equipment operates normally under non-condensing humidity conditions up to 93%,

relative humidity at 100°F (38°C).

4 3 2 1

24V 24C (0V)

TB2

6 5 4 3 2 1

TB1

- COMM + COMM SHIELD

TB2-1 to 24C of next annunciator.

TB2-2 from 24C of FACU power

supply or previous annunciator.

TB2-3 to 24V of next annunciator.

TB2-4 from 24V of FACU power

supply or previous annunciator.

TB1-1 SHIELD to next annunciator.

TB1-2 SHIELD from FACU or previous annunciator.

TB1-3 +COMM to next annunciator.

TB1-4 +COMM from FACU or previous annunciator.

TB1-5 -COMM to next annunciator.

TB1-6 -COMM from FACU

or previous annunciator.

4606-9102 LCD Annunciator installation instructions

Installing the

4606-9102 LCD

Annunciator

Figure 3. Power and RUI Communicating Wiring to TB1 and TB2

3. Using switch SW2 (see Figure 4), set the annunciator’s address in accordance

with Table 2. Switches SW2-1 through SW2-7 set the annunciator’s address, and switch SW2-8

sets the annunciator’s baud rate.

SW2-8 OFF or OPEN = 1200 Baud.

SW2-8 ON or CLOSED = 9600 Baud.

Figure 4. DIP switch SW2

Continued on the next page.

24C (0V) +24VDC

24C (0V)

+24VDC

TB1

TB2

-COMM (RUI-)

+COMM (RUI+)

SHIELD

+COMM (RUI+)

-COMM (RUI-)

GROUND HARNESS

733-936

Note: DIP switch SW2

is located at the bottom of the

electronics assembly.

Position of 3 shown

in OFF position.

Example depicts:

Address = 4

Baud Rate = 9600

4606-9102 LCD Annunciator installation instructions

Address chart

Table 2: Address chart

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 ADDRESS

OFF ON ON ON ON ON ON =ADDRESS 1

ON OFF ON ON ON ON ON = ADDRESS 2

OFF OFF ON ON ON ON ON =ADDRESS 3

ON ON OFF ON ON ON ON = ADDRESS 4

OFF ON OFF ON ON ON ON =ADDRESS 5

ON OFF OFF ON ON ON ON = ADDRESS 6

OFF OFF OFF ON ON ON ON =ADDRESS 7

ON ON ON OFF ON ON ON = ADDRESS 8

OFF ON ON OFF ON ON ON =ADDRESS 9

ON OFF ON OFF ON ON ON = ADDRESS 10

OFF OFF ON OFF ON ON ON =ADDRESS 11

ON ON OFF OFF ON ON ON = ADDRESS 12

OFF ON OFF OFF ON ON ON =ADDRESS 13

ON OFF OFF OFF ON ON ON = ADDRESS 14

OFF OFF OFF OFF ON ON ON =ADDRESS 15

ON ON ON ON OFF ON ON = ADDRESS 16

OFF ON ON ON OFF ON ON =ADDRESS 17

ON OFF ON ON OFF ON ON = ADDRESS 18

OFF OFF ON ON OFF ON ON =ADDRESS 19

ON ON OFF ON OFF ON ON = ADDRESS 20

OFF ON OFF ON OFF ON ON =ADDRESS 21

ON OFF OFF ON OFF ON ON = ADDRESS 22

OFF OFF OFF ON OFF ON ON =ADDRESS 23

ON ON ON OFF OFF ON ON = ADDRESS 24

OFF ON ON OFF OFF ON ON =ADDRESS 25

ON OFF ON OFF OFF ON ON = ADDRESS 26

OFF OFF ON OFF OFF ON ON =ADDRESS 27

ON ON OFF OFF OFF ON ON = ADDRESS 28

OFF ON OFF OFF OFF ON ON =ADDRESS 29

ON OFF OFF OFF OFF ON ON = ADDRESS 30

OFF OFF OFF OFF OFF ON ON =ADDRESS 31

ON ON ON ON ON OFF ON = ADDRESS 32

OFF ON ON ON ON OFF ON =ADDRESS 33

ON OFF ON ON ON OFF ON = ADDRESS 34

OFF OFF ON ON ON OFF ON =ADDRESS 35

ON ON OFF ON ON OFF ON = ADDRESS 36

OFF ON OFF ON ON OFF ON =ADDRESS 37

ON OFF OFF ON ON OFF ON = ADDRESS 38

OFF OFF OFF ON ON OFF ON =ADDRESS 39

ON ON ON OFF ON OFF ON = ADDRESS 40

OFF ON ON OFF ON OFF ON =ADDRESS 41

ON OFF ON OFF ON OFF ON = ADDRESS 42

OFF OFF ON OFF ON OFF ON =ADDRESS 43

ON ON OFF OFF ON OFF ON = ADDRESS 44

OFF ON OFF OFF ON OFF ON =ADDRESS 45

ON OFF OFF OFF ON OFF ON = ADDRESS 46

OFF OFF OFF OFF ON OFF ON =ADDRESS 47

ON ON ON ON OFF OFF ON = ADDRESS 48

OFF ON ON ON OFF OFF ON =ADDRESS 49

ON OFF ON ON OFF OFF ON = ADDRESS 50

OFF OFF ON ON OFF OFF ON =ADDRESS 51

ON ON OFF ON OFF OFF ON = ADDRESS 52

OFF ON OFF ON OFF OFF ON =ADDRESS 53

ON OFF OFF ON OFF OFF ON = ADDRESS 54

OFF OFF OFF ON OFF OFF ON =ADDRESS 55

ON ON ON OFF OFF OFF ON = ADDRESS 56

OFF ON ON OFF OFF OFF ON =ADDRESS 57

ON OFF ON OFF OFF OFF ON = ADDRESS 58

OFF OFF ON OFF OFF OFF ON =ADDRESS 59

ON ON OFF OFF OFF OFF ON = ADDRESS 60

OFF ON OFF OFF OFF OFF ON =ADDRESS 61

ON OFF OFF OFF OFF OFF ON = ADDRESS 62

OFF OFF OFF OFF OFF OFF ON =ADDRESS 63

ON ON ON ON ON ON OFF = ADDRESS 64

4606-9102 LCD Annunciator installation instructions

Continued on the next page.

OFF ON ON ON ON ON OFF =ADDRESS 65

ON OFF ON ON ON ON OFF = ADDRESS 66

OFF OFF ON ON ON ON OFF =ADDRESS 67

ON ON OFF ON ON ON OFF = ADDRESS 68

OFF ON OFF ON ON ON OFF =ADDRESS 69

ON OFF OFF ON ON ON OFF = ADDRESS 70

OFF OFF OFF ON ON ON OFF =ADDRESS 71

ON ON ON OFF ON ON OFF = ADDRESS 72

OFF ON ON OFF ON ON OFF =ADDRESS 73

ON OFF ON OFF ON ON OFF = ADDRESS 74

OFF OFF ON OFF ON ON OFF =ADDRESS 75

ON ON OFF OFF ON ON OFF = ADDRESS 76

OFF ON OFF OFF ON ON OFF =ADDRESS 77

ON OFF OFF OFF ON ON OFF = ADDRESS 78

OFF OFF OFF OFF ON ON OFF =ADDRESS 79

ON ON ON ON OFF ON OFF = ADDRESS 80

OFF ON ON ON OFF ON OFF =ADDRESS 81

ON OFF ON ON OFF ON OFF = ADDRESS 82

OFF OFF ON ON OFF ON OFF =ADDRESS 83

ON ON OFF ON OFF ON OFF = ADDRESS 84

OFF ON OFF ON OFF ON OFF =ADDRESS 85

ON OFF OFF ON OFF ON OFF = ADDRESS 86

OFF OFF OFF ON OFF ON OFF =ADDRESS 87

ON ON ON OFF OFF ON OFF = ADDRESS 88

OFF ON ON OFF OFF ON OFF =ADDRESS 89

ON OFF ON OFF OFF ON OFF = ADDRESS 90

OFF OFF ON OFF OFF ON OFF =ADDRESS 91

ON ON OFF OFF OFF ON OFF = ADDRESS 92

OFF ON OFF OFF OFF ON OFF =ADDRESS 93

ON OFF OFF OFF OFF ON OFF = ADDRESS 94

OFF OFF OFF OFF OFF ON OFF =ADDRESS 95

ON ON ON ON ON OFF OFF = ADDRESS 96

OFF ON ON ON ON OFF OFF =ADDRESS 97

ON OFF ON ON ON OFF OFF = ADDRESS 98

OFF OFF ON ON ON OFF OFF =ADDRESS 99

ON ON OFF ON ON OFF OFF = ADDRESS 100

OFF ON OFF ON ON OFF OFF =ADDRESS 101

ON OFF OFF ON ON OFF OFF = ADDRESS 102

OFF OFF OFF ON ON OFF OFF =ADDRESS 103

ON ON ON OFF ON OFF OFF = ADDRESS 104

OFF ON ON OFF ON OFF OFF =ADDRESS 105

ON OFF ON OFF ON OFF OFF = ADDRESS 106

OFF OFF ON OFF ON OFF OFF =ADDRESS 107

ON ON OFF OFF ON OFF OFF = ADDRESS 108

OFF ON OFF OFF ON OFF OFF =ADDRESS 109

ON OFF OFF OFF ON OFF OFF = ADDRESS 110

OFF OFF OFF OFF ON OFF OFF =ADDRESS 111

ON ON ON ON OFF OFF OFF = ADDRESS 112

OFF ON ON ON OFF OFF OFF =ADDRESS 113

ON OFF ON ON OFF OFF OFF = ADDRESS 114

OFF OFF ON ON OFF OFF OFF =ADDRESS 115

ON ON OFF ON OFF OFF OFF = ADDRESS 116

OFF ON OFF ON OFF OFF OFF =ADDRESS 117

ON OFF OFF ON OFF OFF OFF = ADDRESS 118

OFF OFF OFF ON OFF OFF OFF =ADDRESS 119

Table 2: Address chart

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 ADDRESS

4606-9102 LCD Annunciator installation instructions

Installing the

4606-9102 LCD

Annunciator

4. Mount the annunciator in the back box using the two slotted screws provided, see Figure 5.

Figure 5. LCD Assembly

IMPORTANT:

- Use the holes specified in Figure 5 to install the LCD assembly.

- The trim plate covers a hole in the keyboard which provides access to the display’s

contrast adjustment potentiometer.

5. Adjust the contrast located on the lower left-end corner of the electronics assembly, see Figure

5, using a small screw driver. Turn the potentiometer and observe the LCD display until the

contrast is at the correct setting.

6. Label the user-defined labels appropriately. Pull the top of the label pocket forward and insert

the user-defined labels.

7. Using the four oval-head screws provided, mount the trim plate to the back box, see Figure 6.

Figure 6. Expanded view of 4606-9102 LCD Annunciator

Continued on the next page.

Slotted screws

part no.412-059

Contrast adjustment

Label pocket

Four oval head screws

(part no. 411-702)

LCD assembly

Back box

Two slotted screws

(part no. 412-059)

Trim plate

4606-9102 LCD Annunciator installation instruction

General wiring

precautions

• All wiring must be copper conductors only.

• Do not exceed the maximum wiring lengths specified in the wire length tables in this

document.

• If shielding is used:

- Maintain the metallic continuity of the shield throughout the entire length of cable.

- The entire length of the cable must have a resistance greater than 1 X 106Ohms to earth

ground.

- Ensure the shield is connected to a SHIELD terminal at each annunciator, and is

terminated only at the main panel.

• Ensure underground wiring is free of water.

• Do not run wires through elevator shafts.

• Wire runs in plenums must be in a conduit unless they are rated for plenum use.

• Splicing is permitted in the following situations:

- All connections are soldered (rosin-core solder), crimped in metal sleeves, or

encapsulated with an epoxy resin.

- When using solder or crimped metal sleeves, ensure the junction is insulated with a high

grade electrical tape that equals the quality of the original insulating jacket.

- The continuity of the shield is maintained throughout the length of the cable.

• Do not run other wiring in the same conduit as system wiring.

Specific wiring

precaution

• Ensure 24V power wiring is power limited.

• Communication wiring is supervised and power limited.

• 4606-9102 LCD Annunciator wiring that leaves the building, above or below ground,

requires overvoltage suppression at both ends for the communication and the power

wiring. Communication and power wiring must meet the following requirements using:

- A Simplex Model 2081-9044 overvoltage protector (200 mA) or a Simplex Model

2081-9027 (200 mA) isolated loop circuits protector.

- Simplex Model 2081-9028 (5-amp) isolated loop circuit protector.

- For underground wiring, select the appropriate isolated loop circuit protector. Run the

circuit wiring in a separate parallel wiring trough, to separate it from any commercial

power distribution wiring.

- For overhead wiring, select the appropriate isolated loop circuit protector. The wiring is

limited to one contiguous property and the total wire length must not exceed 2500 feet

(762 meters). Run the circuit wiring on separate poles, to separate it from any poles

supporting commercial power distribution wiring. Run the wiring in parallel with direct

relation to the commercial power distribution. The separation is a minimum distance,

whichever is greater, of 100 feet (30.48 meters), or the maximum span between any two

adjacent poles of either the system’s circuit or the commercial power distribution circuit.

• For the maximum wire lengths with or without circuit protectors, see Tables 3 through 6.

Wire length

tables

Table 3 and Table 4 show the maximum wire lengths possible for the power wiring. Table 5

and Table 6 show the maximum wire lengths for the communication wiring.

Note:

• When using multiple annunciators and runs, ensure the total of all runs does not exceed 10,000 feet

(3048 meters), including T-Taps.

• The maximum number of 2081-9044 over-voltage protectors on a single communication loop is four.

The maximum number of 2081-9028 isolated loop circuit protectors on a single communication loop is

four.

Continued on the next page.

4606-9102 LCD Annunciator installation instructions

579-977

Rev. C

Wire length

tables

Communication line tables:

Checkout

procedure

When the installation is complete, verify that the remote annunciator is working correctly:

1. Verify that the LEDs and the LCD are working by turning the keyswitch OFF and then ON. This

process causes the remote annunciator to execute a self-test which checks each LED and the

LCD.

2. Verify that the annunciator communicates properly with the FACU by observing the remote

annunciator. If the annunciator is not wired properly and is not communicating with the FACU,

error messages are displayed and an audible signal is emitted. Also, a card missing trouble is

displayed at the FACU.

Note: For Programming changes, refer to the relevant panel programming manual.

Table 3: With 2081-9044 or 2081-9027 Circuit Protectors

Total Current

(Amps)

12 AWG

(3.309 mm²)

14 AWG

(2.801 mm²)

16 AWG

(1.309 mm²)

18 AWG

(0.823 mm²)

0.100 2,500ft (762m) 2,500ft (762m) 2,371ft (722.68m) 1,409ft (429.46m)

0.200 2,500ft (762m) 1,782ft (543.15m) 889ft (270.96m) 705ft (214.88m)

Table 4: Without 2081-9044 / 2081-9027 Circuit Protectors (or with 2081-9028 Circuit

Protectors)

Total

Current

(Amps)

12 AWG

(3.309 mm²)

14 AWG

(2.801 mm²)

16 AWG

(1.309 mm²)

18 AWG

(0.823 mm²)

0.100 2,500ft (762m) 2,500ft (762m) 2,500ft (762m) 2,349ft (715.97m)

0.200 2,500ft (762m) 2,500ft (762m) 1,482ft (451.71m) 1,175ft (358.14m)

0.300 2,500ft (762m) 1,980ft (603.5m) 988ft (301.14m) 783ft (238.65m)

0.400 2,361ft (719.63m) 1,485ft (452.62m) 741ft (225.85m) 587ft (178.91m)

0.500 1,889ft (575.76m) 1,188ft (362.1m) 593ft (180.74m) 470ft (143.25m)

0.600 1,574ft (479.75m) 990ft (301.75m) 494ft (150.57m) 392ft (119.48m)

0.700 1,349ft (411.17m) 849ft (258.77m) 423ft (128.93m) 336ft (102.41m)

0.800 1,181ft (359.96m) 743ft (226.46m) 371ft (113.08m) 294ft (89.61m)

0.900 1,049ft (319.73m) 660ft (201.16m) 329ft (100.27m) 261ft (79.55m)

1.000 944ft (287.73m) 594ft (181.05m) 296ft (90.22m) 235ft (71.62m)

1.100 859ft (261.82m) 540ft (164.59m) 269ft (81.99m) 214ft (65.22m)

1.200 787ft (239.87m) 495ft (150.87m) 247ft (75.28m) 196ft (59.74m)

With 2081-9027 isolated Loop Circuit Protectors

0.100 2,500ft (762m) 2,500ft (762m) 2,371ft (722.68m) 1,409ft (429.46m)

0.200 2,500ft (762m) 1,782ft (543.15m) 889ft (270.96m) 705ft (214.88m)

Table 5: With 2081-9044 or 2081-9027 Circuit Protectors

12 AWG (3.309 mm²) 14 AWG (2.801 mm²) 16 AWG (1.309 mm²) 18 AWG (0.823 mm²)

2,500ft (762m) 2,500ft (762m) 2,450ft (746.76m) 1,650ft (502.92m)

Table 6: Without 2081-9044 / 2081-9027 Circuit Protectors (or with 2081-9028 Circuit Protectors)

12 AWG (3.309 mm²) 14 AWG (2.801 mm²) 16 AWG (1.309 mm²) 18 AWG (0.823 mm²)

2,500ft (762m) 2,500ft (762m) 2,500ft (762m) 2,500ft (762m)

With 2081-9027 isolated Loop Circuit Protectors

2,500ft (762m) 2,500ft (762m) 2,450ft (746.76m) 1,650ft (502.92m)

4606-9102 LCD Annunciator installation instructions

Table of contents

Other Simplex Fire Alarm manuals

Simplex

Simplex MINIPLEX 4100-9600 User manual

Simplex

Simplex InfoAlarm 4100U User manual

Simplex

Simplex 4098 Instructions for use

Simplex

Simplex 4100-1265 User manual

Simplex

Simplex 4010ES User manual

Simplex

Simplex 4100-1314 User manual

Simplex

Simplex SafeLINC 4100 Instruction Manual

Simplex

Simplex SafeLINC 4100U Maintenance and service guide

Simplex

Simplex SafeLINC 4100 Operating instructions

Simplex

Simplex 4002 User manual

Simplex

Simplex 4099-9032 User manual

Simplex

Simplex 4010ES User manual

Simplex

Simplex 4190 User manual

Simplex

Simplex SafeLINC 4100 User manual

Simplex

Simplex SafeLINC 4100U User guide

Simplex

Simplex Saturn 2500 User manual

Simplex

Simplex 4010 Instruction Manual

Simplex

Simplex 49SVC-CWFIRE User manual

Simplex

Simplex 4010 User manual

Simplex

Simplex 4007ES Panels User manual

Simplex

Simplex 4090-9001 User manual

Simplex

Simplex 4010ES User manual

Simplex

Simplex 4010ES User manual

Simplex

Simplex 4007-9101 User manual

Popular Fire Alarm manuals by other brands

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 installation manual

System Sensor

System Sensor 22051TLE-RF-26 Installation and maintenance instructions

Pittway

Pittway Notifier AM2020 troubleshooting guide

Ampac

Ampac ZoneSense user manual

Kidde

Kidde VM-1 Technical reference manual

LST

LST SIM016-3 Specification sheet

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Owner's Manual & Installation Instructions

bolid

bolid S2000-IP-03 instruction manual

GST

GST DI-9204 Installation

E2S

E2S BExTBG05D instruction manual

Notifier

Notifier UZC-256 installation manual

Fire-Lite Alarms

Fire-Lite Alarms MS-2 instructions

Siemens

Siemens FDOOT221 Technical manual

hyfire

hyfire HY5000 Series install guide

FlameStop

FlameStop PFSIFP8 Installation and operation manual

Radionics

Radionics Radionics 9124 user guide

UniPOS

UniPOS FD 7120 instruction manual

FIREWOLF

FIREWOLF FW-C01224 owner's manual