Simplex 4100ESi User manual

1 LT0638 Iss 1.1 7/2017

READ AND SAVE THESE INSTRUCTIONS - Follow the instructions in this installation

manual. These instructions must be followed to avoid damage to this product and

associated equipment. Product operation and reliability depend upon proper installation.

DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED - Upon

unpacking your Simplex product, inspect the contents of the carton for shipping damage.

If damage is apparent, immediately le a claim with the carrier and notify an authorised

Simplex product supplier.

ELECTRICAL HAZARD - Disconnect electrical eld power when making any internal

adjustments or repairs. All repairs should be performed by a representative or authorised

agent of your local Simplex product supplier.

STATIC HAZARD - Static electricity can damage components. Handle as follows:

• Ground yourself before opening or installing components

• Prior to installation, keep components wrapped in anti-static material at all times

SYSTEM REACCEPTANCE TEST AFTER SOFTWARE CHANGES - To ensure proper

system operation, this product must be tested in accordance with AS1670.1, after any

programming operation or change in site-specic software. Reacceptance testing is

required after any change, addition or deletion of system components, or after any

modication, repair or adjustment to system hardware or wiring. All components, circuits,

system operations, or software functions known to be affected by a change must be 100%

tested. In addition, to ensure that other operations are not inadvertently affected, at least

10% of initiating devices that are not directly affected by the change, up to a maximum of

50 devices, must also be tested and proper system operation veried.

The 4100-6077AU MX Digital Loop Card is a 4 x 10 inch (double-height) PDI module

that interfaces a single MX Digital Loop to the 4100ESi re panel.

Features:

• 4 x 10 inch double-height PDI module

• Interfaces MX Loop to 4100ESi

• Supports up to 250 MX devices

• 500mA Loop power

• Electrically isolated MX Loop with earth fault monitoring

Cautions and

Warnings

Introduction

4100-6077AU

MX Digital Loop Card

Installation Instructions

This publication discusses the following topics:

Topic Page

Introduction to the MX Digital Loop Card 2

Installing the MX Digital Loop Card 4

Conguring the MX Digital Loop Card 6

Wiring the MX Digital Loop Card to Addressable Devices 8

Compatible MX Addressable Devices 10

In this

publication

Introduction to the MX Digital Loop Card

LT0638 Iss 1.1 7/2017 2

The MX Digital Loop Card provides MX loop communications for the Simplex 4100ESi

re alarm panel via a single electrically isolated MX Digital loop. It supports up to 250

MX devices - detectors and modules - and provides up to 500mA of loop power.

The 4100-6077AU MX Digital Loop Card (Figure 1) is a at, 4x10-inch form-factor

module that plugs into the Power Distribution Interface (PDI) of the 4100ESi panel.

An earlier version of the card was supplied as 4100-6077LIM, which included an extra

bracket on which two LIM800 Loop Isolators were mounted and wired.

This version of hardware has been withdrawn, as the 4100-6077AU now includes loop

short circuit protection.

Overview

Physical

Specifications

Status LEDs

Address

Dipswitch Status LEDs

Figure 1. MX Digital Loop Card

Introduction to the MX Digital Loop Card

3 LT0638 Iss 1.1 7/2017

The MX Digital Loop Card features 7 yellow LEDs that are used to indicate the status of

the MX Digital Loop Card. See Table 1 for the LED status denition:

LEDs

Input

Specifications

Environmental

Specifications

Table 1. Status LEDs

LED Name Interpretation Coding Colour

COMM Loss On when the card is not

communicating with the

4100ESi Central Processing

Unit (CPU)

On steady during

communications loss.

Flashing in local mode Yellow

Earth Fault Earth fault trouble On steady when earth fault

is detected on the MX loop

eld wiring

Yellow

L Loop MX loop communications

left channel fault

On steady when no device

response on left channel.

Slow blink = open circuit

loop;

Fast blink = short circuit

loop

Yellow

R Loop MX loop communications

right channel fault

On steady when no device

response on left channel.

Slow blink = open circuit

loop;

Fast blink = short circuit

loop

Yellow

MX Download Service Mode and

Download in progress

On steady for Service

Mode and download in

progress

Yellow

LPS Fault Indicates loop power

supply fault

On steady with loop

power supply failure

(Signal power)

Yellow

EMR Mode LED is currently unused LED is currently unused Yellow

Environmental Operating Temperature 0°C to +45°C

Operating Humidity Up to 93% RH, non-condensing @ 32°C maximum

Power Supply

Input Voltage (nominal) 24VDC

Quiescent or

Alarm Current

No Load Card power 30mA

Signal power 65mA

Full Load Card power 30mA

Signal power 1200mA

Step 1: Installing the MX Digital Loop Card

LT0638 Iss 1.1 7/2017 4

The MX Digital Loop Card mounts in a Cardcage/PDI bay of a 4100ESi panel. It can be

mounted on any available block - see Figure 2. Secure with the screws supplied in the MX

Digital Loop Card kit.

Installation of

the 4100-6077

in Card Cage

Figure 2. 4100ESi MX Digital Loop Card Installation

Step 1: Installing the MX Digital Loop Card

5 LT0638 Iss 1.1 7/2017

In 15U and 8U cabinets utilising the short PDI backplane (PA1098) the 4100-6077AU

MX Digital Loop Card is mounted onto the short PDI backplane using the same mounting

screws included with the Loop Card kit. For increased density, two 4100-6077AU cards

can be mounted on a ME0516 Legacy/Dual Bracket in either the 8U or 15U cabinets.

The ME0516 bracket is not suitable for mounting 4100-6077AU cards in the standard

Simplex expansion bay.

The earlier 4100-6077LIM version of the loop card should not be mounted on the

ME0516 Legacy/Dual Bracket (ME0516), as the resulting module width is too wide and

may interfere with other modules and equipment.

Installation of the

4100-6077

in a 8U/15U

Cabinet

Setting the Address

1. The MX Digital Loop Card Address is set through a Dual-In-Line Package (DIP)

switch SW100, which is a bank of eight switches. From left to right these switches

are designated as SW100-1 through SW100-8 (see Figure 4). Their functions are as

follows:

• SW100-1: This switch sets the baud rate for the internal communications line running

between the MX Digital Loop card and the CPU. Set this switch to ON.

• SW100-2 through SW100-8: These switches set the card address within the Fire Alarm

Control Panel (FACP). Refer to Table 2 for a complete list of switch settings for all of

the possible module addresses.

Note: Set these switches to the value assigned to the MX Digital Loop card by

the 4100ES Programmer.

Setting the

MX Loop Card

Address

Step 2: Configuring the MX Digital Loop Card

Figure 4. DIP Switch SW100

LT0638 Iss 1.1 7/2017 6

Use DIP Switches SW100-2 through

SW100-8 to set the Module Address.

This figure shows an Address of 3.

4100 Comm. Baud Switch

(SW100-1) must be set to ON Position 8 is LSB

(least significant bit)

OFF OFF = ACTIVE

{

1 2 3 4 5 6 7 8

Programming The MX Digital Loop Card is programed using the 4100ESi Programmer. Refer to

LT0619 4100ESi Programming Manual for details.

Step 2: Configuring the MX Digital Loop Card

Table 2. Module DIP Addresses

7 LT0638 Iss 1.1 7/2017

SW100-2 SW100-8

SW100-7

SW100-6

SW100-5

SW100-4

SW100-3 SW100-2 SW100-8

SW100-7

SW100-6

SW100-5

SW100-4

SW100-3

Field Wiring

Specifications

Step 3: Wiring the MX Digital Loop Card to Addressable Devices

The eld wiring of the MX Digital Loop Card shall follow the specications below:

• Maximum devices per loop: 250

• MX device addresses allowed: 1 to 250

• Wire Size: 12 - 18 AWG (3.31 - 0.82 mm2)

• 2000m cable length

• Maximum resistance: 150 ohms, Maximum Capacitance: 0.2 uF, Inductance 1.5 mH

• Shield terminates at the loop card only (if used)

• Maximum voltage: 40V

• Maximum current: 500mA peak

• Ground fault detection: 10K

• All loop wiring is supervised

Note: “T” tapped wiring is permitted as long as the overall wiring complies with the

previously mentioned inductance, capacitance, and resistance parameters and all devices

on the spur map to the same zone.

Table 3. MX Loop Terminal Block Pin out

Pins Description

TB770-1 Left +

TB770-2 Left -

TB770-3 Shield (earth)

TB770-4 Right +

TB770-5 Right -

LT0638 Iss 1.1 7/2017 8

Wiring

Topologies

Step 3: Wiring the MX Digital Loop Card to Addressable Devices

The MX Loop is run as a loop from the MX Digital Loop Card out to the MX Devices and

back to the MX Digital Loop Card. Normally T-Tapping or spurs are not used (as a single

fault will stop the devices working). However, if all the devices have the same function

and map to the same zone then a spur is permitted. The spur can be connected directly to

the loop - as long as all devices on the spur and between the nearest isolators map to the

same zone. Otherwise, insert a 545.800.004 LIM800 SCI into the loop and wire the spur

cable off the S+, S- terminals. This is shown in Figure 5.

The earlier 4100-6077LIM included two LIM800 short circuit isolators at the start and

end of the loop to provide short circuit protection. These are not shown in Figure 5. These

are not required with the 4100-6077AU as it includes short circuit protection.

Full details of the MX Device and Loop wiring can be found in LT0432 4100ESi Field

Wiring Diagrams.

Figure 5. MX Digital Loop Wiring

LOOP RIGHT

MX DIGITAL

LOOP CARD

LOOP LEFT

DET

DET*

DET

MX DIGITAL ADDRESSABLE LOOP WITH ISOLATORS

ADDRESSABLE

DETECTOR SPUR

CONVENTIONAL

DETECTOR SPUR

EOL

DET*

MZAM CP

PLANT

RIAM

LIM

DII

DET

EOL

CONTACT

ADDRESSABLE

DETECTOR SPUR

NOTES: 1. MAY BE CONFIGURED WITH UP TO 250 ADDRESSABLE DEVICES

2. SHORT CIRCUIT ISOLATORS (E.G., LIM800) AT START AND END OF CABLE NOT SHOWN

IB W/

DET

IB W/

DET

KEY

DET ADDRESSABLE DETECTOR

DET* CONVENTIONAL DETECTOR

IB ISOLATOR BASE

CP CALL POINT

RIAM RELAY IAM

LIM LINE ISOLATOR MODULE

DII DUAL INPUT IAM

MZAM MONITOR ZAM

EOL END-OF-LINE RESISTOR

9 LT0638 Iss 1.1 7/2017

Compatible

Devices

Appendix A: MX Addressable Devices

Table 4 lists the MX Devices compatible with the MX Digital Loop Card.

Addressable Interface Modules

Model Description

516.850.051.E 850PH Photoelectric Smoke & Heat detector with SCI, - Modes A2S, A2R

516.850.052.E 850P Photoelectric Smoke detector with SCI

516.850.053.E 850H Heat detector with SCI, - Modes A2S, A2R, CS, CR

516.850.054.E 850PC CO / Photoelectric Smoke / Heat detector with SCI

CP820 CP820 Indoor Call Point

514.800.604.Y CP830 Outdoor Call Point

516.800.958 LPAV3000 Loop Powered Sounder/Beacon base

516.800.957 LPSB3000 Loop Powered Sounder base

MIM800 MIM800 Mini IAM Input Module

CIM800 CIM800 Dual Input Module

RIM800 RIM800 Relay Output Module

SNM800 SNM800 Signal Notication Module

DIM800 DIM800 Detector Input Module (Dual)

577.800.006 DDM800 Universal Fire & Gas Detector Module (Dual)

516.018.014 VIO800 VESDA Interface Module

555.800.065 MIO800 Multi-I/O Module

516.800.960 LPSY800R Loop Powered Sounder - Indoor Red

516.800.961 LPSY800W Loop Powered Sounder - Indoor White

516.800.962 LPSY865R Loop Powered Sounder - Outdoor Red

516.800.963 LPAV800R Loop Powered Sounder Beacon - Indoor Red

516.800.964 LPAV800W Loop Powered Sounder Beacon - Indoor White

516.800.965 LPAV865 Loop Powered Sounder Beacon - IP65 Red

Table 4. Compatible MX Devices

Table 5. Compatible MX Ancillary Devices

Compatible

Devices

Table 5 lists the MX Ancillary Devices (non-Addressable) compatible with the MX Digital

Loop Card.

Non-Addressable Interface Modules

Model Description

517.050.042 4B-C Continuity Base

516.800.910 802SB Loop Powered Sounder Base

545.800.004 LIM800 Loop Isolator Module

516.800.911 901SB Externally Powered Sounder Base

Johnson Controls • Southbank, VIC • 3006 • AUS LT0638 Iss 1.1 7/2017

www.simplex-re.com

Other manuals for 4100ESi

Table of contents

Other Simplex Fire Alarm manuals

Simplex

Simplex Foundation 2606-9111 Series User manual

Simplex

Simplex SafeLINC 4120 User manual

Simplex

Simplex SafeLINC 4100U User guide

Simplex

Simplex 4010 User manual

Simplex

Simplex 4906-9253 User manual

Simplex

Simplex SafeLINC 4100U User manual

Simplex

Simplex SafeLINC 4100 Operating instructions

Simplex

Simplex 4098 Instructions for use

Simplex

Simplex 4010ES User manual

Simplex

Simplex 4007ES Panels User manual

Simplex

Simplex 4099-9032 User manual

Simplex

Simplex 4099-5210 User manual

Simplex

Simplex SafeLINC 4100 User manual

Simplex

Simplex SafeLINC 4100U Maintenance and service guide

Simplex

Simplex 4903 User manual

Simplex

Simplex SafeLINC 4020 Quick guide

Simplex

Simplex TFX-500M User manual

Simplex

Simplex 49SVC-CWFIRE User manual

Simplex

Simplex 4010ES User manual

Simplex

Simplex 4001-9403 User manual

Simplex

Simplex SafeLINC 4100 User manual

Simplex

Simplex 4190 User manual

Simplex

Simplex SafeLINC 4100 User manual

Simplex

Simplex 4100ES-S1 Maintenance and service guide

Popular Fire Alarm manuals by other brands

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 installation manual

System Sensor

System Sensor 22051TLE-RF-26 Installation and maintenance instructions

Pittway

Pittway Notifier AM2020 troubleshooting guide

Ampac

Ampac ZoneSense user manual

Kidde

Kidde VM-1 Technical reference manual

LST

LST SIM016-3 Specification sheet

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Owner's Manual & Installation Instructions

bolid

bolid S2000-IP-03 instruction manual

GST

GST DI-9204 Installation

E2S

E2S BExTBG05D instruction manual

Notifier

Notifier UZC-256 installation manual

Fire-Lite Alarms

Fire-Lite Alarms MS-2 instructions

Siemens

Siemens FDOOT221 Technical manual

hyfire

hyfire HY5000 Series install guide

FlameStop

FlameStop PFSIFP8 Installation and operation manual

Radionics

Radionics Radionics 9124 user guide

UniPOS

UniPOS FD 7120 instruction manual

FIREWOLF

FIREWOLF FW-C01224 owner's manual