SIIG USB 2.0 Switch User manual
1
04-0318C
USB 2.0 Switch
Quick Installation Guide
Introducing the USB 2.0 Switch
The USB 2.0 Switch is designed to share USB device(s)
between multiple systems.
Features and Benefits
• Compliant with USB Specifications, Revision 2.0.
Hot-swapping feature allows you to attach/detach
USB devices without powering down your
computer
• Use keyboard Hotkey control (Windows only) or
Power LED/Manual switching button to switch
between computers
• Designed for USB devices including printers,
scanners,harddiskdrives,cameras,CD-ROMSand
Zip drives. Note: Not designed to work with
keyboard or mouse
System Requirements
• PC or Mac®computer with an available USB port
(USB 2.0 recommended)
• Windows®7 (32-/64-bit) / Vista (32-/64-bit) / XP
(32-/64-bit) / Server 2003 & 2008 (32-/64-bit) /
2000/ ME / 98SE
• Mac OS®X v10.0 or later
2
Package Contents
•USB 2.0 Switch
• USB cables (6 Ft, Type A to Type B)
• Software CD and quick installation guide
Layout
Do not connect the USB 2.0 Switch to your system until
after the driver has been installed. Please refer to the
Installation section starting on page 4 to install its driver.
USB 2.0 Switch 2-to-1
• Two Type B connectors for system connection
• One Type A connector for device connection
• Convenient manual switching buttons
To USB device
(Type A connector)
(Type B connector)
Power LED/Manual
To PC
Figure 1. USB 2.0 Switch 2-to-1
switching button
3
USB 2.0 Switch 4-to-1
• Four Type B connectors for system connection
• One Type A connector for device connection
• Convenient manual switching buttons
Figure 2. USB 2.0 Switch 4-to-1
Power LED/Manual switching button
To PC
(Type B connector)
To PC
(Type B connector)
To USB device
(Type A connector)
4
Windows Installation
Important: Do not connect the USB 2.0 Switch to your
system until after the driver has been installed. In order
for the driver to install properly the Power LED to that
system must be switched to another system. For example,
if you connect port A to system A, make sure the Power
LED on port A is not lit.
Windows 7 (32-/64-bit) / Windows Vista (32-/64-bit)
1. Insert the driver CD after Windows boots.
At the AutoPlay box: Click Run Setup.exe
If AutoPlay doesn't start: Click Start, in Start Search
type D:\Setup.exe, press Enter. (Change D: to
match your CD/DVD-ROM drive letter)
2. At User Account Control, click Allow.
3. Select your language, then click OK.
4. Click Next, Next, then Finish.
5. Plug the USB 2.0 Switch into an available USB port
(USB 2.0 recommended) with the supplied USB
cables and the driver will install automatically.
6. Press the Power LED/Manual switching button
thatmatchesthesystemtocompletetheinstallation.
5
Windows XP (32-/64-bit) / Server 2003 (32-/64-bit)
1. Insert the driver CD after Windows boots.
2. AutoRun should start the installation. If AutoRun
doesn't start, click Start, Run, type D:\setup.exe,
then click OK. (Change D:tomatch your CD/DVD-
ROM drive letter)
3. Select your language, then click OK.
4. Click Next, Next, then Finish.
5. Plug the USB 2.0 Switch into an available USB port
(USB 2.0 recommended) with the supplied USB
cables and the driver will install automatically.
6. Press the Power LED/Manual switching button
thatmatches the system to complete the installation.
Windows Server 2008 (32-/64-bit)
1. Insert the driver CD after Windows boots.
At the AutoPlay box: Click Run Setup.exe.
If AutoPlay doesn't start: Click Start, in Start Search
type D:\Setup.exe, press Enter. (Change D: to
match your CD/DVD-ROM drive letter)
2. Select your language, then click OK.
3. Click Next, Next, then Finish.
4. Plug the USB 2.0 Switch into an available USB port
(USB 2.0 recommended) with the supplied USB
cables and the driver will install automatically.
5. Press the Power LED/Manual switching button
thatmatches the system to complete the installation.
6
Windows 2000 / ME
1. Insert the driver CD after Windows boots.
2. AutoRun should start the installation. If AutoRun
doesn't start, click Start, Run, type D:\setup.exe,
then click OK. (Change D: to match your CD/
DVD-ROM drive letter)
3. Select your language, then click OK.
4. Click Next, Next, then Finish.
5. Restart Windows. When Windows resumes, plug
the USB 2.0 Switch into an available USB port (USB
2.0 recommended) with the supplied USB cables
and the driver will install automatically.
6. Press the Power LED/Manual switching button
thatmatches the system to complete the installation.
Windows 98SE
1. Insert the driver CD after Windows boots.
2. AutoRun should start the installation. If AutoRun
doesn't start, click Start, Run, type D:\setup.exe,
then click OK. (Change D: to match your CD/DVD-
ROM drive letter)
3. Select your language, then click OK.
4. Click Next, Next, then Finish.
5. Restart Windows. When Windows resumes, plug
the USB 2.0 Switch into an available USB port (USB
2.0 recommended) with the supplied USB cables.
6. When Windows prompts for the driver, click Next.
7
7. Select Search for the best driver..., and click Next.
8. Clear all check boxes, click Next, click Next again.
Note: If prompted for Windows Installation CD-
ROM, click OK. Insert this CD, then click OK again.
9. Click Finish. If prompted, click Yes to restart.
To Verify Windows Installation
1. Go to Device Manager to verify installation.
For Windows 7:Right click Computer, click Manage,
then click Device Manager.
For Windows Vista: Right click Computer, click
Manage,click Continue,thenclickDeviceManager.
For Windows XP / Server 2003 / 2000: Right click My
Computer, click Manage, then click Device
Manager.
For Windows Server 2008: Right click Computer,
click Manage, double click Diagnostics, then click
Device Manager.
For Windows ME / 98SE: Right click My Computer,
click Properties, then click Device Manager.
2. Depending on the status of the Power LED/Manual
Switching Button, use the option that best matches
the system.
Power LED is lit: Double click Universal Serial Bus
controllers and Generic USB Hub should be
displayed.
8
Power LED is off: Double click Human Interface
Devices. HID-compliant device and either USB
Human Interface Device or USB Input Device
should be displayed.
Windows Device Switching
Hotkey Control, Status Indicator and Manual switching
button are the three methods that can be used to switch
devices between systems.
Note: For Mass Storage devices such as flash drives,
USB memory card readers and CD-ROMs, before
switching the USB device to another system, it must be
released from the system that controls it. Use Windows
Safely Remove Hardware feature, located in the
taskbar, to Stop the USB device.
Hotkey Control
Press Ctrl+F11 to switch the USB device to the current
system.
Status Indicator
1. The Status Indicator is located in the taskbar by the
system clock. The indicator has three functions:
Red: Another system is accessing the device -
switching not allowed.
Green: The current system controls the device.
Yellow: No system controls the device - switching
is allowed.
9
2. Double click the USB Sharing icon to start USB
sharing program manually.
3. Right click the Status Indicator and select Switch
can also switch USB access to the current system.
Note: Devices such as external hard drives and
printers send signals back and forth to your
computer when they are connected. This causes
the Status Indicator toremainred. Switching is still
possible by clicking Yes in the Enforce Switching
pop-up box.
Manual Switching Button
Press a Power LED/Manual switching button to switch to
another system.
Mac OS Installation
No driver installation is necessary. Simply plug the USB
2.0 Switch into an available USB port (USB 2.0
recommended).
Mac OS Device Switching
Device switching is controlled by the Power LED/Manual
switching button. Follow the instructions in the next
section for your device type.
10
Memory Card Readers
1. Dragthememory card'sdriveiconintotheTrashcan.
2. Remove the memory card from the card reader
then press a switching button to change systems.
3. Insert a memory card into the memory card reader.
Mass Storage Devices
CD-ROMs, flash drives, external hard disk drives, and Zip
drives typically add drive icons to the desktop. Use the
directions below for switching these devices.
1. Drag the drive icon into the Trashcan.
2. Press the switching button to change systems.
3. The drive icon will appear on the other system.
Other Devices
For other devices just press the switching button to change
to another system.
Connecting USB Devices
When connecting your USB device(s) to the USB 2.0 Switch,
follow the USB device's driver installation procedures.
Other manuals for USB 2.0 Switch
2
Table of contents
Other SIIG Switch manuals
SIIG
SIIG SlimHub 4000P User manual
SIIG
SIIG AV-GM04P3-S1 User manual
SIIG
SIIG AV-GM04P3-S1-W User manual
SIIG
SIIG CE-KV0612-S1 Product information sheet
SIIG
SIIG CE-CM0011-S1 User manual
SIIG
SIIG JU-SW4112 User manual
SIIG
SIIG JU-SC0211-S1 User manual
SIIG
SIIG 1394 User manual
SIIG
SIIG CE-H23012-S1 Product information sheet
SIIG
SIIG Hi-Speed USB 4-Port Bay Hub User manual
SIIG
SIIG AV-GM09V3-S1E User manual
SIIG
SIIG 2x1 VGA Switch User manual
SIIG
SIIG JU-H42B22-S2 User manual
SIIG
SIIG MultiView CE-H26311-S1 User manual
SIIG
SIIG USB 2.0 4-Port Bay Hub User manual
SIIG
SIIG JU-SC0111-S1 User manual
SIIG
SIIG JU-H70411-S2 User manual
SIIG
SIIG DisplayPort 2-Port KVM Switch User manual
SIIG
SIIG FireWire User manual
SIIG
SIIG US22 Series User manual
