Siemens 2000592-001 User manual
GAS CHROMATOGRAPHY
p
process
ADVANCE NETWORK COMMUNICATIONS
BOARD/DATANET (ANCB/DN)
User’s Manual Edition 1/2007
Advance Network Communications
Board/DataNET (ANCB/DN)
Revised Printing – January 2007 User’s Manual
2000592-001
Copyright Notice
©2002-2007 by Siemens
All rights reserved.
This publication is for information only. The contents are subject to change without notice and should not
be construed as a commitment, representation, warranty, or guarantee of any method, product, or device
by Siemens.
Reproduction or translation of any part of this publication beyond that permitted by Sections 107 and 109
of the United States Copyright Act without the written consent of the copyright owner is unlawful.
Inquiries regarding this manual should be addressed to:
Siemens Energy & Automation, Inc.
7101 Hollister Road
Houston, TX 77040
U.S.A.
Table of Contents
Preface iii
Technical Support iv
Safety Practices and Precautions v
Chapter 1: Installation 1
Overview 1
ANCB/DN Specifications 3
ANCB Installation 5
Site Wiring Requirements 7
CE Installations 11
DataNET Connections 13
DataNET Copper Connections 14
DataNET Fiber Optic Connections 16
Data Communications Setup 21
Chapter 2: Configuring Your PC 22
Establishing a Connection 27
Setting Network Address 30
Assigning an IP Address 32
Firmware Updates 33
Command Summary 35
Chapter 3: Command Descriptions 35
Troubleshooting 45
ANCB Description 46
ANCB LEDs Description & Operation 49
Chapter 4: DataNET Troubleshooting Guide 52
Parts Catalog 55
Chapter 5: Introduction 55
Available Parts 56
Glossary Definitions of Important Terms 57
2000592-001 Table of Contents •i
Preface
Audience & Purpose This manual is intended for maintenance personnel and describes how
to install the Advance Network Communication Board/DataNET
(ANCB/DN) into an Advance Maxum™Gas Chromatograph or Advance
Network Access Unit.
Chapter Contents The manual provides the following information:
Topic Page
Chapter 1. Installation 1
Chapter 2. Data Communications Setup 21
Chapter 3.Command Summary 35
Chapter 4. Troubleshooting 45
Chapter 5. Parts Catalog 55
Glossary 57
2000592-001 Preface •iii
Technical Support
Getting Help At Siemens Energy & Automation, Inc. we take pride in the on going
support we provide our customers. When you purchase a product, you
receive a detailed manual, which should answer your questions;
however, our technical support service provides a special “hot” line as an
added source of information.
If you require assistance call:
In the United States: (800) 448-8224
Internationally: 001-918-662-7030
Before You Call Before you call one of our technical support lines, please have the
following information available to help our representative answer your
questions:
1. Unit Serial Number and Date of Installation
2. Installed software version number (if applicable)
3. Description of problem
4. LEDs status on ANCB.
iv •Preface 2000592-001
Safety Practices and Precautions
Safety First This product has been designed and tested in accordance with IEC
Publication 1010-1, Safety Requirements for Electronic Measuring
Apparatus, and has been supplied in a safe condition. This manual
contains information and warnings, which have to be followed by the
user to ensure safe operation and to retain the product in a safe
condition.
Terms in This Manual WARNING statements identify conditions or practices that could result in
personal injury or loss of life.
CAUTION statements identify conditions or practices that could result in
damage to the equipment or other property.
Terms as Marked on
Equipment DANGER indicates a personal injury hazard immediately accessible as
one reads the markings.
CAUTION indicates a personal injury hazard not immediately accessible
as one reads the markings, or a hazard to property, including the
equipment itself.
Symbols in This
Manual
This symbol indicates where applicable cautionary or other
information is to be found.
Symbols Marked on
Equipment DANGER - High voltage
Protective ground (earth) terminal
ATTENTION - Refer to Manual
Grounding the
Product A grounding conductor should be connected to the grounding terminal
before any other connections are made.
2000592-001 Safety Practices and Precautions •v
Safety Practices and Precautions, Continued
Correct Operating
Voltage Before switching on the power, check that the operating voltage listed on
the equipment nameplate agrees with the available line voltage.
DANGER Arising
from Loss of Ground Any interruption of the grounding conductor inside or outside the
equipment or loose connection of the grounding conductor can result in a
dangerous unit. Intentional interruption of the grounding conductor is not
permitted.
Safe Equipment If it is determined that the equipment cannot be operated safely, it should
be taken out of operation and secured against unintentional usage.
Use the Proper Fuse To avoid fire hazard, use only a fuse of the correct type, voltage rating
and current rating as specified in the parts list for your product. Use of
repaired fuses or short-circuiting of the fuse switch is not permitted.
Safety Guidelines DO NOT open the equipment to perform any adjustments,
measurements, maintenance, parts replacement or repairs until all power
supplies have been disconnected.
Only a properly trained technician should work on any equipment with
power still applied.
When opening covers or removing parts, exercise extreme care since
"live parts or connections can be exposed".
Capacitors in the equipment can retain their charge even after the unit
has been disconnected from all power supplies.
vi •Safety Practices and Precautions 2000592-001
This manual suits for next models
1
Table of contents
Other Siemens Network Hardware manuals
Siemens
Siemens PROFIBUS DP-V1 User manual
Siemens
Siemens RUGGEDCOM RX1511 User manual
Siemens
Siemens RUGGEDCOM WIN5114-V-GPS User manual
Siemens
Siemens SIMATIC TIWAY 1 User manual
Siemens
Siemens SIMATIC NET PROFIBUS OBT User manual
Siemens
Siemens SIMATIC NET RUGGEDCOM APE Instruction sheet
Siemens
Siemens 181 Instruction manual
Siemens
Siemens S223 User manual
Siemens
Siemens 3VL9800-8CA30 User manual
Siemens
Siemens SIMATIC NET User manual
Siemens
Siemens XT55 AVL User manual
Siemens
Siemens RUGGEDCOM WIN5237-IS User manual
Siemens
Siemens ESM User manual
Siemens
Siemens RUGGEDCOM WIN5114-V User manual
Siemens
Siemens RUGGEDCOM WIN7251 User manual
Siemens
Siemens SIRIUS 3RA2913-2BB1 User manual
Siemens
Siemens Simatic S7-400 User manual
Siemens
Siemens SANTIS-ab User manual
Siemens
Siemens SCALANCE W788C-2 User manual
Siemens
Siemens RUGGEDCOM WIN5149 User manual
Popular Network Hardware manuals by other brands
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL product manual
B&B Electronics
B&B Electronics ZXT9-IO-222R2 product manual
Yudor
Yudor YDS-16 user manual
D-Link
D-Link ShareCenter DNS-320L datasheet
Samsung
Samsung ES1642dc Hardware user manual
Honeywell Home
Honeywell Home LTEM-PV Installation and setup guide
