Siemens SIRIUS 3RW44 User manual

Getting Started

Industrial Controls

Function Block Library SIRIUS Soft Starter 3RW44 for SIMATIC PCS 7

SIRIUS Soft Starter 3RW44 PCS 7 Library V8.2

Edition 07/2016

Answers for industry.

SIRIUS Soft Starter 3RW44 PCS 7

Library V8.2

___________________

Industrial Controls

SIRIUS Soft Starter 3RW44

SIRIUS Soft Starter 3RW44 PCS 7

Library V8.2

Getting Started

07/2016

A5E36563533002A/RS

-AA/001

Preface

Security information

Product specific security

information

Introduction

Getting Started

References

List of Abbreviations

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

3ZX1012-0CS16-2CC1

Ⓟ

07/2016 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

SIRIUS Soft Starter 3RW44 PCS 7 Library V8.2

Getting Started, 07/2016, A5E36563533002A/RS-AA/001 5

Table of contents

1 Preface ...................................................................................................................................................... 7

2 Security information................................................................................................................................. 11

3 Product specific security information........................................................................................................ 13

4 Introduction.............................................................................................................................................. 15

4.1 Introduction .............................................................................................................................15

5 Getting Started ........................................................................................................................................ 17

5.1 Installation...............................................................................................................................17

5.2 HW Config...............................................................................................................................18

5.3 CFC.........................................................................................................................................20

5.4 Operator Station......................................................................................................................25

6 References .............................................................................................................................................. 35

7 List of Abbreviations ................................................................................................................................ 37

7.1 Abbreviations ..........................................................................................................................37

Table of contents

SIRIUS Soft Starter 3RW44 PCS 7 Library V8.2

6Getting Started, 07/2016, A5E36563533002A/RS-AA/001

SIRIUS Soft Starter 3RW44 PCS 7 Library V8.2

Getting Started, 07/2016, A5E36563533002A/RS-AA/001 7

Preface

Brief description

The Getting Started of the PCS 7 library for SIRIUS Soft Starter uses a simple example

project to show you the basic procedures:

●Basic configuration steps

●Handling and monitoring different signal blocks

●Parameterization

This Getting Started manual is intended to be an introduction and largely dispenses with

detailed information and background information.

Requirements

Basic knowledge of creating a PCS 7 project is necessary. You will find information about

this in the Process Control System PCS 7; Getting Started (V8.0 or higher with APL)

documentation on the Internet

(https://support.industry.siemens.com/cs/document/109485954).

Conventions

This documentation contains designations of the software interface elements. If you have

installed a multi-language package for the operating system, some of the designations will

be displayed in the base language of the operating system after a language switch and will,

therefore, differ from the designations used in this documentation.

Preface

SIRIUS Soft Starter 3RW44 PCS 7 Library V8.2

8Getting Started, 07/2016, A5E36563533002A/RS-AA/001

Software required for the Getting Started of the PCS 7 block library for Soft Starters

●You can execute the example project on any PC or programming device on which the

following software is installed:

–Windows operating system

–Internet Explorer

–Message Queuing service

–SQL server

Note

The versions required depend on the version of PCS 7 installed.

You can find further relevant details in the following manuals:

–SIMATIC Process Control System PCS 7 PC Configuration and Authorization (V8.0)

on the Internet (https://support.industry.siemens.com/cs/document/68157327/).

–SIMATIC Process Control System PCS 7 Released Modules (V8.0) on the Internet

(https://support.industry.siemens.com/cs/document/109736547/).

●You create the PCS 7 project with SIMATIC Manager.

To do so, follow the instructions in the Process Control System PCS 7; Getting Started

documentation.

Hardware required for creating an example project

Table 1- 1 Soft Starter hardware

Order number

Description

3RW4422-1BC44 SIRIUS Soft Starter, values with 400 V, 40 DEG., Standard: 29 A, 15 KW, inside-delta

circuit: 50 A, 22 KW, 200 … 460 V AC, 230 V AC, screw terminals

3RW4900-0KC00 Communication board PROFIBUS for SIRIUS Soft Starter 3RW44

Note on the firmware version

If the Soft Starter is operated as a DP slave following a Y link with a firmware version

<=*E03*, no DPV1 functionality is available. Firmware version >=*E04* is required for

DPV1 functionality following a Y link.

Preface

SIRIUS Soft Starter 3RW44 PCS 7 Library V8.2

Getting Started, 07/2016, A5E36563533002A/RS-AA/001 9

Creating a PCS 7 project

This PCS 7 example project was created with the following hardware for the automation

station (AS):

Table 1- 2 Hardware - Automation station 1: Configuration direct on the master system

Order number

Description

6ES7 410-5HX08-0AB0

SIMATIC S7-400, CPU 410-5H with 1*DP and 2*PN interfaces

6ES7 407-0KA02-0AA0 SIMATIC S7-400, power supply PS 407 10A, AC 120/230V/10A standard PS

Preface

SIRIUS Soft Starter 3RW44 PCS 7 Library V8.2

10 Getting Started, 07/2016, A5E36563533002A/RS-AA/001

Other manuals for SIRIUS 3RW44

This manual suits for next models

Table of contents

Other Siemens Controllers manuals

Siemens

Siemens Simatic S7-300 User manual

Siemens

Siemens SINUMERIK 840 sl User manual

Siemens

Siemens Powermite 599 Series Owner's manual

Siemens

Siemens SIPROTEC 5 Instruction manual

Siemens

Siemens Simatic S7-300 Assembly Instructions

Siemens

Siemens Simatic S7-300 User manual

Siemens

Siemens Simatic S7-300 User manual

Siemens

Siemens SQM50.261R1Z3 Owner's manual

Siemens

Siemens 3RA2220 User manual

Siemens

Siemens Simatic S7-1500 User guide

Siemens

Siemens N 545D31 User manual

Siemens

Siemens SIMATIC TI555 User guide

Siemens

Siemens SIMATIC S5 Series User manual

Siemens

Siemens 7SR224 Operating and installation instructions

Siemens

Siemens EM 300 User manual

Siemens

Siemens OpenAir GIB13.1 Series User manual

Siemens

Siemens LOGO! 8 User manual

Siemens

Siemens GLB111.9E/MO User manual

Siemens

Siemens SINUMERIK 840D sl User manual

Siemens

Siemens Simatic S7-1500 Parts list manual

Siemens

Siemens SIRIUS 3RW52 User manual

Siemens

Siemens SQM50.484R8A Owner's manual

Siemens

Siemens SSB161.05UT User manual

Siemens

Siemens SIRIUS ET 200S User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide