Siemens RMG 508SE User manual

CONTROL BOX RMG 508SE

3001138

2894

The new RMG 508SE control box, fitted with the reset button extension, replaces control box 508SE, but

does not replace the old 505SE version.

Control box RMG 508SE does not have a delay time between the second stage (terminal 14) and third

stage (terminal 11), as shown on the control box’s diagram under the cover - consequently, you will need to

check the burner for malfunctions.

RESETTING THE CONTROL BOX AND USING DIAGNOSTICS

The control box features a diagnostics function through which any causes of malfunctioning are easily iden-

tified (indicator:

RED LED

To use this function, you must wait at least 10 seconds once it has entered the safety condition (

lock-out

and then press the reset button.

The control box generates a sequence of pulses (1 second apart), which is repeated at constant 3-second

intervals.

Once you have seen how many times the light pulses and identified the possible cause, the system must

be reset by holding the button down for between 1 and 3 seconds.

The methods that can be used to reset the control box and use diagnostics are given below.

RESETTING THE CONTROL BOX

To reset the control box, proceed as follows:

➣

Hold the button down for between 1 and 3 seconds.

The burner restarts after a 2-second pause once the button is released.

If the burner does not restart, you must make sure the limit thermostat is closed.

VISUAL DIAGNOSTICS

Indicates the type of burner malfunction causing lock-out.

To view diagnostics, proceed as follows:

➣

Hold the button down for more than 3 seconds once the red LED (burner lock-out) remains steadily lit.

A yellow light pulses to tell you the operation is done.

Release the button once the light pulses. The number of times it pulses tells you the cause of the mal-

function, indicated in the table below.

Once the operations are done, the control box’s initial state must be restored using the resetting procedure

described above.

BUTTON PRESSED FOR CONTROL BOX STATUS

Between 1 and 3 seconds Control box reset without viewing visual diagnostics.

More than 3 seconds Visual diagnostics of lock-out condition:

(LED pulses at 1-second intervals).

ATTENTION

THIS OPERATION MUST BE CARRIED OUT BY A QUALIFIED TECHNICIAN

=== = = = = = = =

Press reset

for >3s 3sPulses Pulses

RED LED on

wait at least 10s Interval

Lock-out

2894

The sequence of pulses issued by the control box identifies the possible types of malfunction, which are

listed in the table below.

SIGNAL PROBABLE CAUSE

2 pulses

The flame does not stabilise at the end of the safety time:

– faulty ionisation probe;

– faulty or soiled gas valves;

– neutral/phase exchange;

– faulty ignition transformer

– poor burner regulation (insufficient gas).

3 pulses

===

Min. air pressure switch does not close:

– air pressure switch faulty;

– air pressure switch incorrectly regulated;

– max. air pressure switch triggered (if installed).

4 pulses

====

Min. air pressure switch does not open or light in the chamber before firing:

– air pressure switch faulty;

– air pressure switch incorrectly regulated.

7 pulses

=======

Loss of flame during operations:

– poor burner regulation (insufficient gas);

– faulty or soiled gas valves;

– short circuit between ionisation probe and earth.

10 pulses

=====

– Wiring error or internal fault.

This manual suits for next models

Table of contents

Other Siemens Controllers manuals

Siemens

Siemens QPA84 User manual

Siemens

Siemens SIMATIC IPC427C User manual

Siemens

Siemens SIRIUS 3RA142 8XC21 Sries User manual

Siemens

Siemens 91-HF Manual

Siemens

Siemens BR6000 User manual

Siemens

Siemens BACnet User manual

Siemens

Siemens RVP331 User manual

Siemens

Siemens Desigo DXR1.E02PLZ-112 User manual

Siemens

Siemens 1PL618 Series User manual

Siemens

Siemens Acvatix SAS31.03 User manual

Siemens

Siemens Simatic S7-1500 User manual

Siemens

Siemens SINUMERIK 840 Technical manual

Siemens

Siemens N 501 Service manual

Siemens

Siemens RAJA+ 3TE7131-1HC14-1A Operating instructions

Siemens

Siemens 7SR224 User manual

Siemens

Siemens SITOP PSU8600 User manual

Siemens

Siemens Simatic S7-300 User manual

Siemens

Siemens SIMATIC S7-1200 Instruction Manual

Siemens

Siemens ET 200pro User manual

Siemens

Siemens SINUMERIK 840D sl Instruction sheet

Siemens

Siemens GCA 1 Series User manual

Siemens

Siemens SIRIUS 3RW30 User manual

Siemens

Siemens OpenAir GSD 1 Series User manual

Siemens

Siemens CPU 410-5H Process Automation User guide

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide