Siemens SiPass Driver User manual

Installation Instructions

Document No. 565-722

August 2, 2013

SiPass Driver for PXC Modular and PXC-36

Item Number: 565-722, Rev. BA

Page 1 of 2

These installation instructions cover the connection of

the Siemens SiPass Driver to the SiPass system

only.

For hardware installation of the PXC Modular, see

the

PXC Modular Series Installation Instructions

(553-638).

For hardware installation of the PXC-36, see the

PXC Compact 36 Installation Instructions

(553-504).

Product Description

The Siemens SiPass Driver enables communication

between the APOGEE® Automation System and the

Siemens SiPass system.

Product Numbers

License

LSM-INT-SBTSPSS

License to enable the Siemens SiPass

Driver on PXC Modular or PXC-36

hardware.

PXC Modular Series

PXC00-PE96.A

PXC Modular, Ethernet or RS-485

ALN, 96 FLN nodes

PXC00-E96.A

PXC Modular, BACnet/IP or MS/TP

ALN, 96 FLN nodes

PXC100-PE96.A

PXC Modular, Ethernet or RS-485

ALN, 96 FLN nodes, TX-I/O module

support

PXC100-E96.A

PXC Modular, BACnet/IP or MS/TP

ALN, 96 FLN nodes, TX-I/O module

support

PXX-485.3

Expansion Module, three RS-485 FLN

connections

PXC Compact Series

PXC36-PE.A

PXC Compact, 36 point, Ethernet/IP or

RS-485 ALN

PXC36-E.A

PXC Compact, 36 point, BACnet/IP or

MS/TP ALN

Accessories

538-670

Trunk Interface II, 115V

538-675

Trunk Interface II, 230V

536-004

RS-232 Cable

Caution Notation

CAUTION

Equipment damage or loss of data may

occur if you do not follow a procedure as

specified.

Expected Installation Time

30 minutes

Required Tools and Materials

Flat-blade screwdriver (1/8-inch blade width).

Wire strippers.

Cabling and connectors. See the

Connecting the

Driver to the

SiPass System

section.

CAUTION

Always wear an electro-static discharge

(ESD) wrist strap and discharge

accumulated static before touching field

panel components.

Document No. 565-722

Installation Instructions

August 2, 2013

Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as

design improvements are introduced. APOGEE, Insight, and SiPass are registered trademarks of Siemens Industry, Inc. Other product or

Siemens Industry, Inc.

Building Technologies Division

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

USA

Tel. 1 + 847-215-1000

Your feedback is important to us. If you have

comments about this document, please send them

to SBT_technical.editor.us.sbt@siemens.com.

Document No. 565-722

Printed in the USA

Page 2 of 2

Prerequisites

Driver hardware is installed according to its

respective installation instructions.

FLN termination blocks are installed.

One 115V or 230V receptacle (depending on

device) is available to power the Trunk Interface

II.

Ethernet infrastructure is installed.

Depending on the type of installation, other

prerequisites may have to be completed.

Connecting the Driver to the SiPass

System

Follow these steps to connect the driver to the SiPass

System:

1. Install the Trunk Interface II per the diagram in

Figure 1.

2. Connect cables per the diagram in Figure 1.

3. Plug in the power supply for the Trunk Interface II

per the diagram in Figure 1.

Figure 1: Connecting the Driver to the SiPass System.

Table 1. Wiring Pin-outs for RS-232 Cable

(P/N 536-004).

Trunk Interface

(DB-25 Male)

SiPass

(9-pin Female)

Table of contents

Other Siemens Control Unit manuals

Siemens

Siemens SIMATIC ET 200S IM151-1 FO STANDARD User manual

Siemens

Siemens TBM-2 User manual

Siemens

Siemens ALD-2I User manual

Siemens

Siemens SINUMERIK 804D sl Quick start guide

Siemens

Siemens LFE1 Series User manual

Siemens

Siemens SINUMERIK 828D Turning User manual

Siemens

Siemens SIMATIC S7-1500R/H User manual

Siemens

Siemens SIMATIC ET 200SP CM 1xDALI Owner's manual

Siemens

Siemens Simatic S7-1500 User manual

Siemens

Siemens SIMATIC TIM 3V-IE DNP3 User guide

Siemens

Siemens SIMATIC 6ES7135-4MB02-0AB0 User manual

Siemens

Siemens SMF6120 User manual

Siemens

Siemens IM 328-N Operating and installation instructions

Siemens

Siemens ZS-30 User manual

Siemens

Siemens S-60 User manual

Siemens

Siemens SIMOTION D410 User manual

Siemens

Siemens SINUMERIK 840Di User manual

Siemens

Siemens DMS8000 MP4 Series Operating and maintenance instructions

Siemens

Siemens SINUMERIK 840D sl User manual

Siemens

Siemens SINUMERIK 880 SW 6 Technical manual

Siemens

Siemens Siwarex U Application guide

Siemens

Siemens S7-1500 PROFIBUS User manual

Siemens

Siemens LYC11 User manual

Siemens

Siemens LMS14 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual