Siemens SIMATIC ET 200SP User manual

___________________

SIMATIC

ET 200SP

Digital output module

F-DQ 8x24VDC/0.5A PP HF

(6ES7136-6DC00-0CA0)

Manual

05/2017

A5E38578424

-AA

Preface

Documentation guide

Product overview

Connecting

Parameters/address space

Applications of the

F-I/O module

Interrupts/diagnostic

messages

Technical specifications

Response times

Switching of loads

Original operating instructions

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E38578424-AA

Ⓟ

05/2017 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Digital output module F-DQ 8x24VDC/0.5A PP HF (6ES7136-6DC00-0CA0)

Manual, 05/2017, A5E38578424-AA 3

Preface

Purpose of the documentation

This manual supplements the system manual Distributed I/O System ET 200SP

(http://support.automation.siemens.com/WW/view/en/58649293).

Functions that affect the system in general are described in this system manual.

The information in this manual and the system/function manuals provide support when you

commission the system.

A description of the F-system SIMATIC Safety can be found in the programming and

operating manual SIMATIC Safety – Configuring and Programming

(http://support.automation.siemens.com/WW/view/en/54110126).

Conventions

CPU: When the term "CPU" is used in the following, it refers to both the CPUs of the

S7-1500 automation system as well CPUs / interface modules of the ET 200SP distributed

I/O system.

STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the

configuration and programming software " (STEP 7 TIA Portal)".

Note the following identified notes:

Note

note includes important information on the product described in the documentation, on

handling the product or on the part of the documentation to which you ought to pay special

attention.

Standards

You can find a dated reference to the respective standards in the certificate

(https://support.industry.siemens.com/cs/ww/en/view/57141281) or in the EC Declaration of

Conformity (https://support.industry.siemens.com/cs/ww/en/view/71764057) for the

F-module.

Preface

Digital output module F-DQ 8x24VDC/0.5A PP HF (6ES7136-6DC00-0CA0)

4Manual, 05/2017, A5E38578424-AA

Important note for maintaining the operational safety of your system

Note

The operators of systems with safety

-related characteristics must adhere to specific

operational safety requirements. The supplier is also obliged to comply with special product

monitoring measures. Siemens informs system operators in the form of personal notifications

about product developments and properties which may be or

become important issues in

terms of operational safety.

You should subscribe to the corresponding notifications in order to obtain the latest

information and to allow you to make any necessary modifications to your system.

Log on to Industry Online Suppo

rt. Follow the links below and click on "Email on update" on

the right

-hand side in each case:

•

SIMATIC S7-300/S7-300F

(https://support.industry.siemens.com/cs/products?pnid=13751&lc=en-WW)

•

SIMATIC S7-400/S7-400H/S7-400F/FH

(https://support.industry.siemens.com/cs/products?pnid=13828&lc=en-WW)

•

SIMATIC WinAC RTX (F) (https://support.industry.siemens.com/cs/ww/en/ps/13915)

•

SIMATIC S7-1500/SIMATIC S7-1500F

(https://support.industry.siemens.com/cs/products?pnid=13716&lc=en-WW)

•

SIMATIC S7-1200/SIMATIC S7-1200F

(https://support.industry.siemens.com/cs/products?pnid=13683&lc=en-WW)

•

Distributed I/O (https://support.industry.siemens.com/cs/products?pnid=14029&lc=en-

WW)

•

STEP 7 (TIA Portal)

(https://support.industry.siemens.com/cs/products?pnid=14340&lc=en-WW)

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions only form one element of such a concept.

Customer is responsible to prevent unauthorized access to its plants, systems, machines

and networks. Systems, machines and components should only be connected to the

enterprise network or the internet if and to the extent necessary and with appropriate security

measures (e.g. use of firewalls and network segmentation) in place.

Additionally, Siemens’ guidance on appropriate security measures should be taken into

account. For more information about industrial security, please visit

(http://www.siemens.com/industrialsecurity).

Siemens’ products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends to apply product updates as soon as available and to

always use the latest product versions. Use of product versions that are no longer supported,

and failure to apply latest updates may increase customer’s exposure to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under (http://www.siemens.com/industrialsecurity).

Digital output module F-DQ 8x24VDC/0.5A PP HF (6ES7136-6DC00-0CA0)

5Manual, 05/2017, A5E38578424-AA

Table of contents

Preface ................................................................................................................................................... 3

1 Documentation guide .............................................................................................................................. 7

2 Product overview .................................................................................................................................. 11

2.1 Properties................................................................................................................................11

3 Connecting ........................................................................................................................................... 14

3.1 Wiring and block diagram .......................................................................................................14

4 Parameters/address space ................................................................................................................... 16

4.1 Parameters .............................................................................................................................16

4.2 Explanation of parameters ......................................................................................................18

4.2.1 F-parameters ..........................................................................................................................18

4.2.1.1 F-parameters ..........................................................................................................................18

4.2.1.2 Behavior after channel fault ....................................................................................................18

4.2.1.3 Reintegration after channel fault.............................................................................................18

4.2.2 Parameters of the channels....................................................................................................19

4.2.2.1 Maximum test period...............................................................................................................19

4.2.2.2 Disable dark test for 48 hours.................................................................................................19

4.2.2.3 Activated .................................................................................................................................20

4.2.2.4 Max. readback time dark test..................................................................................................20

4.2.2.5 Max. readback time light test ..................................................................................................22

4.2.2.6 Activated light test...................................................................................................................23

4.2.2.7 Channel failure acknowledge..................................................................................................24

4.3 Address space ........................................................................................................................24

5 Applications of the F-I/O module ........................................................................................................... 26

5.1 Installation of the ground line between the power supply and the BaseUnit ..........................26

5.2 Application: Wiring a load to each digital output.....................................................................27

5.3 Application: Wiring two loads in parallel to each digital output...............................................29

5.4 Application: Connection of a fail-safe digital input to each digital output................................31

5.5 Application: Connection of the ET 200SP digital output module F-RQ

1x24VDC/24..230VAC/5A (6ES7136-6RA00-0BF0) ..............................................................35

6 Interrupts/diagnostic messages............................................................................................................. 37

6.1 Status and error display ..........................................................................................................37

6.2 Interrupts.................................................................................................................................40

6.3 Diagnostics alarms..................................................................................................................42

6.4 Value status ............................................................................................................................46

7 Technical specifications ........................................................................................................................ 47

Table of contents

Digital output module F-DQ 8x24VDC/0.5A PP HF (6ES7136-6DC00-0CA0)

6Manual, 05/2017, A5E38578424-AA

A Response times .................................................................................................................................... 50

B Switching of loads ................................................................................................................................. 51

B.1 Connecting capacitive loads .................................................................................................. 51

B.2 Switching of inductive loads................................................................................................... 53

Digital output module F-DQ 8x24VDC/0.5A PP HF (6ES7136-6DC00-0CA0)

7Manual, 05/2017, A5E38578424-AA

Documentation guide

The documentation for the SIMATIC ET 200SP distributed I/O system is arranged into three

areas.

This arrangement enables you to access the specific content you require.

Basic information

The system manual describes in detail the configuration, installation, wiring and

commissioning of the SIMATIC ET 200SP. distributed I/O system. The STEP 7 online help

supports you in the configuration and programming.

Device information

Product manuals contain a compact description of the module-specific information, such as

properties, wiring diagrams, characteristics and technical specifications.

Documentation guide

Digital output module F-DQ 8x24VDC/0.5A PP HF (6ES7136-6DC00-0CA0)

8Manual, 05/2017, A5E38578424-AA

General information

The function manuals contain detailed descriptions on general topics regarding the SIMATIC

ET 200SP distributed I/O system, e.g. diagnostics, communication, Web server, motion

control and OPC UA.

You can download the documentation free of charge from the Internet

(http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual-

overview/tech-doc-et200/Pages/Default.aspx).

Changes and supplements to the manuals are documented in a Product Information.

You can download the product information free of charge from the Internet

(https://support.industry.siemens.com/cs/us/en/view/73021864).

Manual Collection ET 200SP

The Manual Collection contains the complete documentation on the SIMATIC ET 200SP

distributed I/O system gathered together in one file.

You can find the Manual Collection on the Internet

(http://support.automation.siemens.com/WW/view/en/84133942).

"mySupport"

With "mySupport", your personal workspace, you make the most of your Industry Online

Support.

In "mySupport" you can store filters, favorites and tags, request CAx data and put together

your personal library in the Documentation area. Furthermore, your data is automatically

filled into support requests and you always have an overview of your current requests.

You need to register once to use the full functionality of "mySupport".

You can find "mySupport" in the Internet (https://support.industry.siemens.com/My/ww/en).

"mySupport" - Documentation

In the Documentation area of "mySupport", you have the possibility to combine complete

manuals or parts of them to make your own manual.

You can export the manual in PDF format or in an editable format.

You can find "mySupport" - Documentation in the Internet

(http://support.industry.siemens.com/My/ww/en/documentation).

Documentation guide

Digital output module F-DQ 8x24VDC/0.5A PP HF (6ES7136-6DC00-0CA0)

Manual, 05/2017, A5E38578424-AA 9

"mySupport" - CAx Data

In the CAx Data area of "mySupport", you can have access the latest product data for your

CAx or CAe system.

You configure your own download package with a few clicks.

In doing so you can select:

●Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN

macro files

●Manuals, characteristics, operating manuals, certificates

●Product master data

You can find "mySupport" - CAx Data in the Internet

(http://support.industry.siemens.com/my/ww/en/CAxOnline).

Application examples

The application examples support you with various tools and examples for solving your

automation tasks. Solutions are shown in interplay with multiple components in the system -

separated from the focus in individual products.

You can find the application examples on the Internet

(https://support.industry.siemens.com/sc/ww/en/sc/2054).

TIA Selection Tool

With the TIA Selection Tool, you can select, configure and order devices for Totally

Integrated Automation (TIA).

This tool is the successor of the SIMATIC Selection Tool and combines the known

configurators for automation technology into one tool.

With the TIA Selection Tool, you can generate a complete order list from your product

selection or product configuration.

You can find the TIA Selection Tool on the Internet

(http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool).

Documentation guide

Digital output module F-DQ 8x24VDC/0.5A PP HF (6ES7136-6DC00-0CA0)

10 Manual, 05/2017, A5E38578424-AA

SIMATIC Automation Tool

You can use the SIMATIC Automation Tool to run commissioning and maintenance activities

simultaneously on various SIMATIC S7 stations as a bulk operation independently of the TIA

Portal.

The SIMATIC Automation Tool provides a multitude of functions:

●Scanning of a PROFINET/Ethernet network and identification of all connected CPUs

●Address assignment (IP, subnet, gateway) and station name (PROFINET device) to a

CPU

●Transfer of the data and the programming device/PC time converted to UTC time to the

module

●Program download to CPU

●Operating mode switchover RUN/STOP

●Localization of the CPU by means of LED flashing

●Reading out CPU error information

●Reading the CPU diagnostic buffer

●Reset to factory settings

●Updating the firmware of the CPU and connected modules

You can find the SIMATIC Automation Tool on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/98161300).

PRONETA

With SIEMENS PRONETA (PROFINET network analysis), you analyze the plant network

during commissioning. PRONETA features two core functions:

●The topology overview independently scans PROFINET and all connected components.

●The IO check is a fast test of the wiring and the module configuration of a system.

You can find SIEMENS PRONETA on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/67460624).

Other manuals for SIMATIC ET 200SP

101

Table of contents

Other Siemens Control Unit manuals

Siemens

Siemens LMO14 Series User manual

Siemens

Siemens CZM-4 User manual

Siemens

Siemens SIMATIC FM 450-1 User manual

Siemens

Siemens Simatic S7-1500 User manual

Siemens

Siemens Maxum II PD PA AP User manual

Siemens

Siemens SINUMERIK 840D User manual

Siemens

Siemens SIMOTION TM15 Quick start guide

Siemens

Siemens FDCI223 User manual

Siemens

Siemens SIMATIC S7-1200 Parts list manual

Siemens

Siemens 6ES7134-4FB51-0AB0 User manual

Siemens

Siemens 3RK1200-0C.03-0AA2 User manual

Siemens

Siemens SIMATIC FM 351 User manual

Siemens

Siemens SIMATIC Panel PC 677 User manual

Siemens

Siemens SINUMERIK Series Parts list manual

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens TC65 User manual

Siemens

Siemens LMV36.520A1 Operator's manual

Siemens

Siemens SIPROCESS GA700 User manual

Siemens

Siemens SIRIUS 3RT User manual

Siemens

Siemens SITRANS FM MAG 8000 IIoT User manual

Siemens

Siemens SIMATIC CC712 User manual

Siemens

Siemens SIPROTEC 7SJ61 Instruction manual

Siemens

Siemens SINAMICS PM230 User manual

Siemens

Siemens SIRIUS ACT 3SU1400-1EK10-6AA0 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual