Siemens A80407-01 User manual

QUICK REFERENCE GUIDE

DT INSTALLATION PROCEDURE A FOR

GCP 4000 DISPLAY MODULE A80407-01

(AND EARLY -03) USING A COMPACT

FLASH DEVICE

Document Number SIG-QG-09-02

Version B.1

The following procedure should be used when upgrading

the Diagnostic Utility (DT) in a GCP 4000 Display Module,

P/N 8000-80407-0001 and early versions of P/N 8000-

80407-0003 (see note below).

NOTE

If the A80407-03 Display Module is labeled DISPLAY

II, you must use DT Installation Procedure B

(document No. SIG-QG-09-03) to install the DT

software.

INSTALLING THE DT IN GCP 4000 DISPLAY MODULE

A80407-01 OR EARLY A80407-03

To perform this procedure you will need a pre-

loaded Compact Flash device, Siemens part number

Z224-9V244-A010, containing the latest DT software

version that is compatible with the currently

installed MCF. In addition to the preloaded Compact

Flash device you will need a PCMCIA adapter

module to install the Compact Flash device in the

Display Module. This adapter module can be

purchased from Siemens by ordering P/N Z714-

02115-0000.

NOTE

Upgrading the DT Utility in the Display Module will

NOT interfere with the safe operation of the

highway crossing warning system.

1. Locate and remove the A80407 display module from

the GCP 4000 chassis.

2. Locate the boot DIP switches on the top edge of the

Display Module (accessible through the slot in the top

of the Display Module case, figure #1). The Display

Module boot DIP-switch normal positions are: switch

1= OFF, switch 2 = ON. For Phase 1 stylus calibration,

position both switches to the OFF position (see figure

#2 below).

3. Insert the Siemens provided Compact Flash memory

device into the PC card adapter. Then install the

adapter in the A80407 Display Module through the

slot in the top of the Display Module case (figure #3).

Reinstall the Display Module in the GCP 4000 chassis

as shown in figure #4 below. Apply power to the GCP

4000 if not already powered up.

4. With the use of the stylus, calibrate the display by

tapping the + sign as it appears on the display (figure

#5). At the end of this calibration process a 30

second timer will run (figure #6). Tap the display one

more time before this timer expires to save the new

display module calibration settings.

5. The screen shown in figure #7 indicates the

completion of Phase 1 and provides additional

information in preparation for Phase 2. Remove the

A80407 Display Module from the 4000 chassis and

then remove the PC card adapter and Compact Flash.

Set both Display Module DIP switches back to the

normal position: switch 1 = OFF and switch 2 = ON.

Reinstall the PC card adapter and Compact Flash in

the A80407 Display Module. Reinstall the Display

Module in the GCP 4000 chassis.

6. After reinstalling the A80407 module in the GCP 4000,

the display will execute its boot cycle. After the

completion of the boot up process the display will

show a prompt asking if “you want to reformat the

FlashFX Disk?”. Select Yes (figure #9). When the

WARNING appears select OK (figure #10).

NOTE

In the following figures the DT version number

at the top of the screen and the OS Build

number at the bottom will vary depending on

the DT and OS software versions installed.

Normal position

OFF 1

calibration position

OFF 1

All

rights reserved

#10

7. After selecting OK the next screen (figure #11) will

prompt one more time to erase the FlashFX Disk.

Select Yes. At this point Phase 2 DT installation will

begin. Ensure that the two option boxes are checked

as shown in figure #12 below and then select Next >.

#11

#12

8. The following display will ask you if you want to

delete the support files, select Yes to start the

process.

NOTE

This upgrade may take up to 10 minutes to

complete. Do not disturb the system during this

process.

9. At the completion of this process, a screen message

will indicate that the installation has been completed

(see below). Remove the A80407 Display Module

from the GCP chassis and then remove the PC card

adapter and Compact Flash.

10. Reinstall the A80407 Display Module in the GCP 4000.

After completion of the boot process the following

message will appear: “Creating file description data.

DT will restart when done” (see figure #13). Select

OK to initiate the process.

#13

11. The process will be followed by the screen shown in

figure #14, and the display will again reboot. At the

conclusion of this boot cycle the display will resume

normal operation and will indicate the conditions of

the GCP 4000 and highway crossing warning system.

#14

12. This concludes the DT software installation and

upgrade. NO ADDITIONAL TESTING IS REQUIRED.

For verification of the DT installation, select MORE

(MAIN in DT 5.0.7 and later) on the Track status

screen and then select HELP (ABOUT in DT 5.0.7 and

later) on the subsequent screen to view the DT

version. Verify that the display indicates the proper

DT version (e.g., 5.0.7).

*Refer to GCP 4000 Crossing System Maintainer’s Handbook,

Document Number: SIG-00-04-02 Version B, dated March

2007 or to 4000 GCP Crossing System Field Manual, Document

Number SIG-00-08-10 Version B or later, for additional

information regarding installation of DT software in a GCP

4000 Display Module

PRINTED IN USA

This manual suits for next models

Other Siemens Control Unit manuals

Siemens

Siemens SINUMERIK 840D sl Instruction sheet

Siemens

Siemens SIMATIC FM 450-1 User manual

Siemens

Siemens ASIsafe SIRIUS 3RK1205-0B.00-0AA2 User manual

Siemens

Siemens SIRIUS 3RT1916-4KA User manual

Siemens

Siemens SIMATIC CC712 User manual

Siemens

Siemens GAMMA instabus Touch control TC5 User manual

Siemens

Siemens SIMATIC 8DO DC24V/0.5 A User manual

Siemens

Siemens REP-1 User manual

Siemens

Siemens SENTRON User manual

Siemens

Siemens SINAMICS S110 Datasheet

Siemens

Siemens SINUMERIK 840D sl User manual

Siemens

Siemens SIMATIC NET RUGGEDCOM APE1808 Instruction sheet

Siemens

Siemens SIMATIC 6DL1 136-6AA00-0PH1 User manual

Siemens

Siemens Q3920 User manual

Siemens

Siemens CB15 User manual

Siemens

Siemens VAG61 Series User manual

Siemens

Siemens CM 1243-5 User manual

Siemens

Siemens HLIM User manual

Siemens

Siemens SIRIUS 3RA11 User manual

Siemens

Siemens SINUMERIK 840D sl Quick start guide

Siemens

Siemens SIJECT 16i User manual

Siemens

Siemens Simatic 6ES7132-4HB01-0AB0 User manual

Siemens

Siemens SINAMICS G130 User manual

Siemens

Siemens SIMATIC ET 200SP TM ECC 2xPWM ST User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual