Siemens SIMATIC 8DO 24 V DC/0.5 A HF User manual
SIMATIC ET 200S distributed I/O Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
_
_____________
_
_____________
_
_____________
Properties 1
Parameters
2
Diagnostics
3
SIMATIC
ET 200S distributed I/O
Digital electronic module 8DO
DC24V/0.5A HF (6ES7132-4BF00-
0AB0)
Manual
10/2009
A5E02515349-01
Legal information
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation for the specific task, in particular its warning notices and
safety instructions. Qualified personnel are those who, based on their training and experience, are capable of
identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E02515349-01
Ⓟ 09/2009
Copyright © Siemens AG 2009.
Technical data subject to change
Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Manual, 10/2009, A5E02515349-01 3
Table of contents
1 Properties .................................................................................................................................................. 5
1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0) ....................................5
2 Parameters.............................................................................................................................................. 11
2.1 Parameters...................................................................................................................................11
3 Diagnostics.............................................................................................................................................. 13
3.1 Diagnostics using LED display.....................................................................................................13
3.2 Error types....................................................................................................................................14
Table of contents
Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
4 Manual, 10/2009, A5E02515349-01
Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Manual, 10/2009, A5E02515349-01 5
Properties 1
1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-
0AB0)
Properties
● Digital electronic module with eight outputs
● Output current 0.5 A per output, aggregate current 4 A
● Rated load voltage 24 VDC
● Diagnostics: wire break
● Short-circuit protection
● Suitable for solenoid valves, DC contactors, and indicator lights
● Supports isochronous operation
Requirements for operation
It is possible to operate the 8DO 24 V DC/0.5 A HF digital electronic module with the
following interface modules, as of the specified order numbers:
Interface module Order number (or higher) Firmware version (or
higher)
IM 151-1 STANDARD
IM 151-1 FO STANDARD
IM 151-1 HIGH FEATURE
6ES7151-1AA05-0AB0
6ES7151-1AB05-0AB0
6ES7151-1BA02-0AB0
V2.2.4
---
V2.2.3
IM 151-3 PN
IM 151-3 PN FO
IM 151-3 PN HIGH FEATURE
6ES7151-3AA23-0AB0
6ES7151-3BB23-0AB0
6ES7151-3BA23-0AB0
V6.1
V6.1
V6.1
IM 151-1 BASIC 6ES7151-1CA00-0AB0 ---
IM151-1 COMPACT 6ES7151-1CA00-1BL0
6ES7151-1CA00-3BL0
---
IM 151-7 CPU
IM 151-7 CPU FO
IM 151-7 F-CPU
6ES7151-7AA20-0AB0
6ES7151-7AB00-0AB0
6ES7151-7FA20-0AB0
---
IM 151-8 PN/DP CPU
IM 151-8 PN/DP F-CPU
6ES7151-8AB00-0AB0
6ES7151-8FB00-0AB0
---
Properties
1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
6 Manual, 10/2009, A5E02515349-01
General terminal assignment
Note
Terminals A4, A8, A3 and A7 are only available at specified terminal modules.
Terminal assignment for 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Terminal Assignment Terminal Assignment Notes
1 DO
0 5 DO
1
2 DO
2 6 DO
3
3 DO
4 7 DO
5
4 DO
6 8 DO
7
A4 AUX1 A8 AUX1
A3 AUX1 A7 AUX1
•DOn: Output signal, Channel n
•AUX1: M chassis ground (from power module) or potential bus
(freely usable up to 230 VAC)
Usable terminal modules
Terminal assignment for 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
TM-E15C26-A1
(6ES7193-4CA50-0AA0)
TM-E15C24-01
(6ES7193-4CB30-0AA0)
Spring terminal
TM-E15S26-A1
(6ES7193-4CA40-0AA0)
TM-E15S24-01
(6ES7193-4CB20-0AA0)
Screw-type terminal
TM-E15N26-A1
(6ES7193-4CA80-0AA0)
TM-E15N24-01
(6ES7193-4CB70-0AA0)
Fast Connect
$8;
$
$
$
$
'2
'2
'2
'2
0$8;
FRQGXFWRU
&RQQHFWLRQH[DPSOHV
Properties
1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Manual, 10/2009, A5E02515349-01 7
Two-wire connection
The following configuration example shows a 2-wire connection with the electronic modules
8DO DC24V. You require further terminals so that sufficient terminals are available for the
chassis ground connection M when the TM-E15S26-A1 terminal modules are used. In the
example this is implemented by the add-on terminal TE-U120S4x10 that can be mounted as
from a width of 120 mm (8 EMs). You can naturally also use other terminals for this
configuration (for example, ET 200S potential distribution module 4POTDIS).
3
4
2
1
5
6
$$
$$
$$$$$ $$$$$$$$$$ $
$$
$$$$
$$
$$
$$
$$
$8;
$$
'&9
① Terminal module TM-P15S23-A0
② Power module PM-E 24 VDC
③ Electronic modules 8DI DC24V
④ Terminal modules TM-E15S26-A1
⑤ Actuators in 2-wire connection
⑥ Add-on terminal TE-U120S4x10
Properties
1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
8 Manual, 10/2009, A5E02515349-01
Block diagram
3
3
0
/
(76
%DFNSODQHEXV
LQWHUIDFH
%DFNSODQHEXV
5HYHUVHSRODULW\
SURWHFWLRQ
Figure 1-1 Block diagram 8DO DC24V/0.5A HF
Properties
1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Manual, 10/2009, A5E02515349-01 9
Technical data 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Dimensions and weight
Width (mm) 15
Weight Approx. 40 g
Module-specific data
Supports isochronous operation Yes
Number of outputs 8
Length of cable
•Unshielded max. 600 m
•Shielded max. 1,000 m
Parameter length 3 bytes
Address space 1 byte
Voltages, currents, potentials
Rated load voltage L+ (from the power module) 24 VDC
•Reverse polarity protection Yes1
Total current of the outputs (per module) 4 A
Electrical isolation
•Between the channels No
•Between the channels and backplane bus Yes
Permissible potential difference
•Between the different circuits 75 VDC / 60 VAC
Insulation tested 500 VDC
Current consumption
•From the rated load voltage L+ (no load) Max. 5 mA per channel
Power dissipation of the module Typically 1.5 W
Status, interrupts, diagnostics
Status display Green LED per channel
Diagnostics function
•Group error Red "SF" LED
•Diagnostic functions readable Yes
Data for selecting an actuator
Output voltage
•At signal "1" Min. L+ (-1 V)
Output current
•At signal "1"
– Rated value
– Permitted range
0.5 A
7 mA up to 0.6 A
•With signal "0" (leakage current) max. 0.3 mA
Output delay (for resistive load)
Properties
1.1 Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
Digital electronic module 8DO DC24V/0.5A HF (6ES7132-4BF00-0AB0)
10 Manual, 10/2009, A5E02515349-01
•At "0" to "1" max. 300 μs
•At "1" to "0" max. 600 μs
Load resistor range 48 Ω to 3.4 kΩ
Lamp load max. 5 W
Connecting two outputs in parallel
•For redundant triggering of a load Yes (per module)
•To increase performance No
Control of a digital input Yes
Switch rate
•For resistive load 100 Hz 2
•On inductive load 2 Hz 2
•For lamp load 10 Hz 2
Limitation (internal) of the voltage induced on
circuit interruption
typ. L + (-55 V)
Reverse-voltage proof Yes, if using the same load voltage as at the
power module
Short-circuit protection of the output Yes (per channel)3
1 Polarity reversal can lead to the digital outputs being connected through.
2 The diagnostic message "short circuit" is based on the thermal short-circuit detection in the output
driver.
3 limited to typ. 1.5 A
This manual suits for next models
1
Table of contents
Other Siemens Control Unit manuals
Siemens
Siemens MVS661 N Series User manual
Siemens
Siemens K60R User manual
Siemens
Siemens EFB300 User manual
Siemens
Siemens SITOP modular 6EP1961-3BA20 User manual
Siemens
Siemens SIMATIC S7-300 FM 350-1 User manual
Siemens
Siemens SIMOTION D4 5 Series User manual
Siemens
Siemens SIMATIC ET 200SP User manual
Siemens
Siemens SINUMERIK 840D sl User manual
Siemens
Siemens FDK:085U0321 User manual
Siemens
Siemens multiranger 200 User guide
Siemens
Siemens SIPROTEC PROFINET IO User manual
Siemens
Siemens 3KC ATC6300 User manual
Siemens
Siemens SIM-16RC User manual
Siemens
Siemens SIMATIC 6DL1 136-6AA00-0PH1 User manual
Siemens
Siemens 986-88301A User manual
Siemens
Siemens SiPass Driver User manual
Siemens
Siemens SIMATIC ET 200SP User manual
Siemens
Siemens PSO+ User manual
Siemens
Siemens SINUMERIK 840D Parts list manual
Siemens
Siemens SINUMERIK 808D Quick start guide
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
