Siemens AE-30U User manual

P/N 315-085099-16

Operation and Installation Instructions

Model AE-30U

Alarm Extender Module

Fire Safety

Operation

The SIEMENS Model AE-30U Alarm Extender

Module is designed to provide one Style Y (Class

) super-vised notification appliance circuit,

utilizing polarized, parallel connected notification

appliances.

Actuation of the module is caused by

high-going DC input signal between 12 and 24 volts

above system common. Dual input activation termi-

nals are provided to facilitate programming.

The Model AE-30U contains a yellow LED trouble

indicator to display open or shorted alarm lines

except when that particular module is not in an

activated condition.

The yellow LED can be lamp tested from the

system control panel.

Installation

1. Mount the module to the horizontal mounting

brackets in the control enclosure.

2. Install the Model JA-5 (5 in. long) bus connector

cable assembly between receptacle P2 of the

module and receptacle P1 of the module or

control panel immediately preceding it in the

bus.

Note: If the preceding module is on another

row in the enclosure, a JA-24 (24 in.

long) bus connector cable assembly will

be required.

3. Modules are to be bus-connected from right to

left. For two-row enclosures, the modules in the

lower row are to be connected from left to right.

Succeeding rows are to be alternately con-

nected, right to left, left to right, etc.

4. If a module is the last module in the system,

install either a JS-30 (30 in. long) or JS-64

(64 in. long) bus connector assembly from the

unused receptacle of the last module to

terminal 41 of the CP-35 control panel. This

completes the module supervision circuit.

5. If a DC notification appliance circuit is to be

used, install a JP-D program plug into

receptacle P2 of the CP-35 control panel.

Note: If a battery charger/transfer module is

used, the program plug is not

necessary.

If an AC notification appliance circuit is to

be used, install a JP-A program plug into

receptacle P2 of the control panel.

Note: When a JP-A program plug is used, an

EL-32 end of line device is required for

the notification appliance circuit.

6. Wire the circuits as described in the MODEL

CP-35 CONTROL PANEL INSTALLATION

AND MAINTENANCE INSTRUCTIONS, P/N

315-085063 and the CP-35 WIRING DIAGRAM,

P/N 315-084902. The maximum line resistance

should be 3 ohms, and a minimum of 14 AWG

wire is recommended. All wiring should comply

with the local and national codes that apply to

the particular installation.

Operational Test

Refer to INSTALLATION AND WIRING in the

Instruction Manual (P/N 315-085063) for the

control panel.

Troubleshooting

Refer to TROU LESHOOTING THE CP-35 in the

Instruction Manual for the control panel.

Siemens Building Technologies, Inc.

8 Fe nwood Road

Flo ham Pa k, New Je sey 07932

Siemens Building Technologies, Ltd.

2 Kenview Bouleva d

B ampton, Onta io L6T 5E4 CN

P/N 315-085099-16

NOTES:

1. When emergency power is provided using

charger/ transfer module, Model C-35, 24 VDC

notification appliances must be used with EOL

device, Model EL-31. When C-35 is not used,

120 VAC notification appliances may be

employed by use of AC program plug, Model

JP-A, in P2 of CP-35 and Model EL-32 EOL

device, or by use of 24 VDC notification

appliances with DC program plug, Model

JP-D, in P2 and Model EL-31 EOL device.

2. Notification appliance circuits may be

activated from the silenceable system alarm

output signal, terminal 36 of CP-35, or from the

non-silenceable system alarm output signal,

terminal 42 of CP-35. When other alarm signals

such as coding or time delay/limit are required,

see individual module connection diagrams.

3. Use only the compatible polarized notification

appliances listed in P/N 315-096363.

4. To use power limited wiring to NFPA 70, NEC

Article 760, the notification appliance circuits

(terminals 3 and 4) must use the PLM-35

module. Refer to Instructions P/N 315-093495.

NOTE:

Refer to the BI-35 Installation

Instructions, P/N 315-086257,

for detailed wiring information

when using the AE-30U in

conjunction with the BI-35

module.

ACTUATION

INPUT

POLARIZEDNOTIFICATION

APPLIANCES (SEE NOTE 3)

END OF LINE DEVICE

(SEE NOTE 1)

CP-35

(SEE NOTE 2)

3 OHMS MAX TOTAL LINE

RESISTANCE OF NOTIFICATION

APPLIANCE CIRCUIT

CONNECTING WIRES

INPUT POWER

(SEE NOTE 1)

CP-35

STYLE Y (CLASS B)

CONNECTED

POLARIZED

NOTIFICATION

APPLIANCES

POLARITY SHOWN IN

SUPERVISORYCONDITION:

SUPV 24 VDC, 5mA

ALARM 24 VDC or 120 VAC,

1.5A MAX

Table of contents

Other Siemens Control Unit manuals

Siemens

Siemens SIMATIC IM 178-4 User manual

Siemens

Siemens SITOP modular 6EP1961-3BA20 User manual

Siemens

Siemens PROFIBUS CP 1542-5 User manual

Siemens

Siemens SINUMERIK 840D sl User manual

Siemens

Siemens SIRIUS ACT 3SU1803-3NB00-1AE1 User manual

Siemens

Siemens TM Timer DIDQ Quick start guide

Siemens

Siemens OMM-2 User manual

Siemens

Siemens RMH760B User manual

Siemens

Siemens MKB-5 User manual

Siemens

Siemens SIMATIC S5 User manual

Siemens

Siemens 7KT1 908 User manual

Siemens

Siemens CM 1243-5 User manual

Siemens

Siemens Simatic S7-1500 Parts list manual

Siemens

Siemens MOD-16 User manual

Siemens

Siemens Simatic 6ES7132-4HB01-0AB0 User manual

Siemens

Siemens XC10 Series Instruction Manual

Siemens

Siemens SIRIUS 3RW5 series Technical Document

Siemens

Siemens VAI61 Series User manual

Siemens

Siemens 3SB5 Instruction Manual

Siemens

Siemens SINUMERIK 840D sl Quick start guide

Siemens

Siemens SINUMERIK 802D Installation guide

Siemens

Siemens Simatic Net Scalance M812 User manual

Siemens

Siemens SINAMICS G120 Datasheet

Siemens

Siemens SIMOTION D4x5 Series User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual