Siemens S6 User manual

Private Communication Systems

Mobile Phones

Service Manual

S6 Power GSM

( S6 Classic GSM)

V 1.2

V1.2 Page 1 of 18 PN MP ST

D. Schnoor

/98

Private Communication Systems

Mobile Phones

Table of Contents

V1.2 Page 2 of 18 PN MP ST

D. Schnoor

/98

Technical Data S6 (D) Power GSM

Length 159 mm

Width 55 mm

Thickness 16/22 mm

Volume 155 cm3

Weight 180 gm (incl. battery)

Performance: GSM class (2 Watt)

Frequency Range: Tx 890-915 MHz

Rx 935-960 MHz

Powersupply: Metal Hydride battery (3,6V/700mAh)

Standby time: up to 60 hours

Talk time: Up to hours.

Carging Time: Full charge in 75 minutes

Display LCD high-resolution graphic display, 97 x 33 pixels, rows

of 16 characters

SIM Card Type: Small (plug in) 3V or 5V

Private Communication Systems

Mobile Phones

General Infor ation

The S6 Power is a consumer handset technically based on E10. It is also available

as a dualrate version (S6 D Power).

Mechanical Concept

Note: All part numbers refer to mechanical drawing in section 4.1!

The S6 Power consists of two boards, the RF & Control module (1010) and the user

interface (1020).

The connection between those two boards is not made by a normal connector with

plug-in contacts, but by a special interconnector (1090) embedded into a shielding

frame (1060). This interconnector is upholding the connection through the pressure

implied on it by the housing.

Be careful when assembling the interconnector. Avoid any kind of dust or dirt

because it will affect the contacts of the interconnector.

The only removable part on the user interface is the ringer gasket (1080) which is

needed to increase the ringer volume.

Furthermore there is a RF-plug on the user interface which has to be plugged into

the appropriate connector on the RF & control module. This conection is very

essential because it is the RF signal from / to the internal antenna.

The shielding is done by the lower case shell (1050) which is covered with a

conductive material, so no additional shielding screen is necessary.

The antenna (1130) is directly screwed into the lower case shell.

V1.2 Page 3 of 18 PN MP ST

D. Schnoor

/98

Private Communication Systems

Mobile Phones

The keypad (1030), the loudspeaker (1120), the microphone (1110), the dust

protection frame (1075) and the display window (1070) are mounted into the upper

case shell (10 0). Make sure that the microphone contacts are properly bent up

when mounting.

When turning in the screws (11 0, 11 5 and 1150) make sure that the right torque is

used (25 Ncm), because this will have an effect on the contacts of the

interconnector.

V1.2 Page 4 of 18 PN MP ST

D. Schnoor

/98

Private Communication Systems

Mobile Phones

S6 Power mechanical drawing

Note: The nu bers shown above are NO ordering nu bers. Please use the nu bers

supplied by your service anager for ordering!

V1.2 Page 5 of 18 PN MP ST

D. Schnoor

/98

Private Communication Systems

Mobile Phones

Disassembling the S6 Power

1. Remove battery and SIM-Card.

2. Unscrew antenna (1130).

3. Unscrew 2 oval head screws (1160) (Torx 1,8x12).

. Turn out 2 short screws (11 0) (Torx 1,8x8).

5. Remove plastic disks (1170) and turn out the 3 long flat head screws

(1150)

(Torx 1,8x12).

6. Lift off the lower case shell (1050).

7. Lift composite of MMI-board (1020) and RF-and controle module (1010) out

of the upper case shell (10 0).

Only for level-2 repairs:

a) Remove ringer gasket (1080) from the MMI board (1020).

b) Remove RF plug from RF- and control module (1010).

c) Take off the MMI board (1020).

d) Take frame (1060) off the RF- and control module (1010).

e) Remove interconnector (1090) from the frame (1060).

8. If necessary: Take battery connector out of lower case shell (1050).

9. Take dust protection frame (1075) off the display glass frame (1070).

10. Take keypad (1030) out of upper case shell (10 0).

11. Remove earphone capsule (1120) and microphone (1110) from upper case

shell.

V1.2 Page 6 of 18 PN MP ST

D. Schnoor

/98

Private Communication Systems

Mobile Phones

Assembling the S6 Power

1. Put earphone capsule (1120) and microphone (1110) into upper case shell

(10 0).

2. Insert keypad (1030) into upper case shell (10 0).

3. Place dust protection frame (1075) on display glass frame (1070).

Attention: The smooth side has to face the MMI.

. If necessary: Insert battery connector into lower case shell (1050).

5. Insert composite of MMI-board (1020) and RF-and controle module (1010)

into upper case shell (10 0).

BEFORE (only for level 2 repairs):

a) Put interconnector (1090) to the frame (1060).

b) Position frame (1060) on the RF- and control module (1010).

c) Place MMI board (1020) on top of frame (1060).

d) Connect RF plug of MMI board (1020) to RF- and control

module (1010).

e) Mount ringer gasket (1080) on the MMI board (1020).

6. Close device with upper case shell (10 0). Make sure that the 6 hooks of

the upper case shell fit firmly into the respective slots of the lower

case shell (1050).

7. Screw 3 long flat head screws (1150) (Torx 1,8x12 /Torque 25 Ncm) into

lower case shell (1050). Close holes with plastic disks (1170)

afterwards.

8. Screw 2 short flat head screws (11 0) (Torx 1,8x8 /Torque 25 Ncm) into

lower case shell.

9. Screw 2 oval head screws (1160) (Torx 1,8x12 /Torque 25 Ncm) into lower

case shell.

10. Screw in Antenna (1130) (Torque 25 Ncm).

11. Insert SIM-Card and battery.

V1.2 Page 7 of 18 PN MP ST

D. Schnoor

/98

Private Communication Systems

Mobile Phones

Handset Datecodes

Siemens is using the industrial standard DIN EN 60062 to indicate the production /

service dates. The code is printed on the IMEI sticker located under the simcard

reader.

The first character of the datecode indicates the year of production:

F = 1995

H = 1996

J = 1997

K = 1998

The second character indicates the month of production:

1-9 = january to september

O = october

N = november

D = december

Example: K1 means that the set was produced in january of 1998.

V1.2 Page 8 of 18 PN MP ST

D. Schnoor

/98

-> YY = Datecode

Private Communication Systems

Mobile Phones

Hardware Concept

Block Diagram

V1.2 Page 9 of 18 PN MP ST

D. Schnoor

/98

Private Communication Systems

Mobile Phones

V1.2 Page 10 of 18 PN MP ST

D. Schnoor

/98

HiGOLD (PMB 2800)

Other manuals for S6

Table of contents

Popular Cell Phone manuals by other brands

Zte

Zte BLADE A520 quick start guide

Nokia

Nokia Lumia 620 user guide

Blackbe;rry

Blackbe;rry KEYone Safety and product information

Bea-fon

Bea-fon X5 Premium quick guide

Blackbe;rry

Blackbe;rry 8707 Series user guide

Blackbe;rry

Blackbe;rry Storm Troubleshooting

LG LM-X420QN user guide

LifeWatch

LifeWatch V user guide

Bea-fon

Bea-fon SILVER LINE SL860 user guide

IKI Mobile

IKI Mobile KF4.5i user manual

Hitech

Hitech HT-850 user guide

Yezz

Yezz Fashion F10 user manual

Point Mobile

Point Mobile PM60 user manual

Blackbe;rry

Blackbe;rry Q10 user guide

Blackbe;rry

Blackbe;rry Bold 9900 user guide

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 user guide

LG LM-K420EMW user guide

ISAFE MOBILE

ISAFE MOBILE IS655.2 operating manual