Sennheiser DW-810ST User manual
Model Name : DW-810ST
User’s Manual
Wireless DECT Headset
INTRODUCTION
Attaching the headband
When you combine a headset with a headband, match the shapes of the triangles.
1. Package Contents
BASE UNIT
HEADSET & HEADBAND
TELEPHONE CORD
POWER ADAPTOR
Detaching the headset
IMPORTANT :Do not separate the headset from the headband using the
microphone boom.
Adjusting the Microphone boom
The microphone boom is flexible, so you can bend the boom
and positon it for comport and best transmission.
The ideal placement for the microphone is usually
At the corner of your mouth, not in front of it,
and about
an inch from tour face.
Be sure that the side of the microphone is pointed
Toward your mouth.
X O
- Speaker Volume Up/Down
- Microphone Mute (Press)
- Fit the headband or ear-hook on the headset
- Adjust the boom arm of your headset so that the microphone is positioned in
the direction of your mouth, as close as possible to your mouth.
-
- For charging of headset, connect supplied usb cable to usb port.of the
headset
2. Headset
Down Up
Mute/ Speaker
volume
Call Hook On/Off
In-Use/On-Off
Indicator
Mute
Micro USB port
Microphone Volume Switch When installed, adjust volume level for the best level of
microphone volume.
Compatibility Switch Select ‘1’ or ‘2’ until a dial tone is heard via the telephone
connection.
3. Base Unit
Compatibility
Switch
Mic. Mute Button
Microphone Volume
Mode Selection
Handset port Plug Handset cord from the phone to Handset port
Telephone port Connect telephone cord to the headset port or handset port of a
telephone / base unit
DC Jack Connect Power Adapter to DC Jack
AUX port
Handset port
Telephone port
4. LED & Audio indicator
Mode indicator
Mic mute indicator
Battery indicator
TEL indicator
DC Jack
Charging Status LEDs status
Charging Battery Indicator : ‘Blinking’ 1 sec-ON, 1sec-OFF
Full Charged Battery Indicator : ‘ON’
Low Battery Battery Indicator : ‘Blinking’ 0.5 sec-ON, 0.5 sec-OFF
Event LEDs status
Press Microphone mute Mute indicator : ‘ON’
Hook Off Selected Mode indicator : ‘ON’
Event Added
Speaker /Microphone volume
UP/DOWN
Beep Sound
(High tone/Low tone)
Max/Min speaker volume reached Double beep
Max/Min microphone volume reached Double beep
Microphone mute/unmute Beep / Double beep
Mute reminder Beep (every 3 seconds)
Hook Off / On Double beep
(High tone / Low tone)
Audio Indicator
Diagram 1 (Desk phone with HEADSET port)
- Plug the supplied telephone cord into the TEL port of the BASE UNIT
- Connect the telephone cord to the HEADSET port of the desk phone
Diagram 2 ( Desk phone without HEADSET port)
- On the desk phone, unplug the handset cable from the phone
- Plug the handset cable into the HANDSET port on the BASE UNIT
- Plug the telephone cord into the TEL port on the BASE UNIT and plug the
other end of the telephone cord into the HADNSET port on the desk phone
5. Setting up the BASE
- Plug the Power Adapter cord on the Base unit.(Note 1)
- Press Hook On/Off switch to make a call
- Select compatibility switch ‘1’ or ‘2’ position until you can hear the dial tone
- Adjust speaker and microphone volume
- Press Hook On/Off switch to end a call
Note 1 : Factory default setup : Paired
Pairing process is automatically proceeding when plug the power adapter into the Base
Unit. (Make sure that headset is placed on the cradle and should be powered on before
power is turned on. If the headset is not placed on the cradle, pairing will be
unsuccessful.)
6. Operational Instruction
1. Cannot hear a dial tone.
☞Please check the cable connection between Base unit and Phone.
☞Check that the power adapter is plugged in and has power
☞Please check the compatibility switch. Adjust compatibility switch until you
can hear the dial tone.
2. Microphone volume (TX) is low / dead.
☞Make sure that the microphone (TX) mute function is deactivated.
☞Check the position of the boom arm and make sure that the microphone is
placed as close as possible to your mouth (approx. 2 fingers distance).
☞Adjust the microphone (TX) volume on the bottom of base unit.
3. Buzzing sound on the headset
☞Telephone may not be fully immune to the radio transmission between your
headset and base. To overcome this problem, move the base unit to at
least 30 cm/12” away from the phone.
4. Headset echoes
☞Adjust the telephone’s volume. If necessary, adjust your microphone volume
on the headset to a lower setting.
6. Headset was working, but it has stopped.
☞Headset may need pairing to the base again. Refer to the ‘Note 1’ on
‘Operational Instruction’
☞Headset battery may be dead. Return the headset to the cradle on the base
unit for charging.
8. Trouble Shooting
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmfu
l interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement:
The base unit complies with FCC radiation exposure limits set forth for an uncontrolled environment. The base unit should be installed and operated with
minimum distance 20cm between the radiator& your body.
The headset unit has been tested and comply with FCC SAR limits.
Table of contents
Other Sennheiser Headset manuals
Sennheiser
Sennheiser SC 260 User manual
Sennheiser
Sennheiser S1 PASSIVE User manual
Sennheiser
Sennheiser SDW 10 HS User manual
Sennheiser
Sennheiser SC 70 USB MS User manual
Sennheiser
Sennheiser HD 250BT User manual
Sennheiser
Sennheiser CC 513 User manual
Sennheiser
Sennheiser PX 210 BT - User manual
Sennheiser
Sennheiser D 10 USB ML User manual
Sennheiser
Sennheiser EPOS SC 660 USB ML User manual
Sennheiser
Sennheiser SH 330 IP User manual
Sennheiser
Sennheiser VMX 100 User manual
Sennheiser
Sennheiser DW Pro1 User manual
Sennheiser
Sennheiser EZX 60 User manual
Sennheiser
Sennheiser Momentum Wireless M2 AEBT User manual
Sennheiser
Sennheiser DW Office USB ML User manual
Sennheiser
Sennheiser SH 338 IP User manual
Sennheiser
Sennheiser HD 350BT User manual
Sennheiser
Sennheiser EPOS ADAPT 230 User manual
Sennheiser
Sennheiser PC 121 Instruction manual
Sennheiser
Sennheiser CC 510 User manual
