SECO-LARM Enforcer E-37EV User manual

Monitors up to three zones per

premises or vehicle, plus

manual paging.

One positive and two negative

instant trigger inputs.

Low-battery indicator.

Red LED transmission indicator.

Manual

E-37EV

Code-learning receiver learns

up to three transmitter codes.

Transmitter can page an

unlimited number of receivers.

Colored LEDs or vibrate

function indicate received page.

Unattended page indicator.

Alarm Pager System

NOTE: Antenna required. See page 3 for more details. Antenna not included.

ENFORCER E-37EV Alarm Pager System

2SECO-LARM U.S.A., Inc.

Introduction

The E-37EV is a sophisticated paging system consisting of two parts: a transmitter with trigger

and timing circuitry, and a matching E-37RV receiver with both vibrating and audible paging

functions.

The pager alerts users when a protected building or vehicle is being vandalized or broken into, or

when someone presses the manual paging button. The transmitter has a maximum output power

of 4 watts as allowed by the FCC.

Mount the E-37EV inside the secure area. The transmitter sends a page signal when triggered.

The page signal is received by the small, highly sensitive, lightweight receiver. The receiver

beeps or vibrates and colored LEDs indicate the type of trigger event.

The system is easy to install in any type of building or vehicle. The two 1.5V AAA-sized batteries

(batteries not included) in the receiver will last approximately one month (5 transmissions/day).

The receiver can be programmed to receive page signals from up to 3 separate transmitters and

the transmitter can page an unlimited number of receivers.

Parts List

1 x Transmitter

1 x Receiver (model E-37RV)

1 x Wire harness

3 x Mounting screws

1 x Radio antenna

adapter cord (18”)

Introduction .........................................................................................................................2

Parts List.............................................................................................................................2

Dimensions ........................................................................................................................2

Specifications......................................................................................................................3

Installation....................................................................................................................... 3-4

Wiring..................................................................................................................................4

Connection Diagram ...........................................................................................................5

Programming ......................................................................................................................5

Audible and Visual Signals Chart........................................................................................6

Operation ........................................................................................................................ 6-7

Warning...............................................................................................................................7

Troubleshooting ..................................................................................................................8

Also available from SECO-LARM .......................................................................................8

Table of Contents

Dimensions

15/16”

(33mm)

41/8”

(105mm)

31/8”

(79mm)

21/8”

(54mm)

3”

(76mm)

5/8”

(16mm)

ENFORCER E-37EV Alarm Pager System

SECO-LARM U.S.A., Inc. 3 SECO-LARM U.S.A., Inc. 33 3

Transmitter Installation

1. Mark locations for drilling the mounting bracket holes. Be careful that the area to be drilled

is free from wiring, trim, and/or any other obstructions.

2. Drill holes at the location marks. Position the transmitter where it will be mounted, but do

not secure immediately.

3. The transmitter should be permanently mounted only after all connections and tests

are made.

NOTES:

Do not mount the E-37EV transmitter in the engine compartment as this automatically voids

the warranty.

Do not power up the transmitter before the antenna connections are made as this may

damage the transmitter.

In a building, mount as close to a window as possible.

In a vehicle, mount under the dashboard or in the glove compartment.

Antenna Installation (see Connection Diagram on pg. 5)

The E-37EV can be connected to one of four types of antennas:

TYPE 1: Strip antenna (A Position)

1. E-37ANT (optional) can be used in either a building or vehicle.

2. Connect the male antenna plug into the transmitter jack marked “ANT.”

3. Place the antenna selection switch in the “A” position.

4. Do not secure the strip antenna to metal, window defrosters, or existing antennas.

Installation

Transmitter

Number of codes

Over 2 million (factory pre-set)

Power

12VDC

RF output power

4W max.

Current drain

Standby

10mA

Active

Frequency

27MHz

Antenna impedance

50 Ω

Range

Up to 1/2mile in open air1

Dimensions

41/8”x31/8”x15/16” (105x79x33 mm)

Weight

5.1-oz (145g)

1 Actual range may vary depending on the environment, installation, and/or antenna.

Receiver

Number of codes

Learns up to 3 transmitter codes

Power

3VDC (2 AAA batteries)2

Battery life

Approx. 1 month3

Current drain

Standby

1mA

Active (Beep)

20mA

Active (Vibrate)

50mA

Dimensions

3”x21/8”x5/8” (76x54x16 mm)

Weight

1.6-oz (45g) (without battery)

2 Batteries not included

3 Based on 5 transmissions/day

Specifications

ENFORCER E-37EV Alarm Pager System

4SECO-LARM U.S.A., Inc.

Wiring

Red Wire –Positive 12VDC power

Connect the red wire to a constant +12VDC power source.

Black Wire –Ground

Connect the black wire to the negative terminal of a 12VDC power source.

Optionally, connect to the frame of the vehicle.

Purple Wire –Positive trigger input

Connect the purple wire to a burglar or car alarm output that outputs +12V when the alarm is

triggered (the trigger signals must be at least 1 second long in order to trigger pager.)

Green Wire –Negative trigger input #1

Connect the green wire to a burglar or car alarm output that outputs ground when the alarm

is triggered (the trigger signals must be at least 1 second long in order to trigger pager.)

Blue Wire –Negative trigger input #2

Connect the blue wire to a burglar or car alarm output that outputs ground when the alarm is

triggered (the trigger signals must be at least 1 second long in order to trigger pager.)

White Wire –Fully automatic radio antenna

Connect the long white wire (female spade plug) to the power antenna wire coming from the

power antenna sensor wire.

Connect the short white wire (male spade plug) to the power antenna wire coming from the

radio switched power lead.

Warning: Do not reverse the white wire connections.

TYPE 2: CB antenna (A Position)

1. Connect the male antenna plug of an optional CB antenna into the transmitter jack marked

“ANT.”

2. Place the antenna selection switch in the “A” position.

TYPE 3: Standard radio antenna (B Position)

1. Disconnect the radio antenna lead going into the radio and connect it to the transmitter jack

marked “ANT.”

2. Connect the provided male-to-male 18” radio antenna adapter cord between the transmitter

jack marked “RADIO” and the radio antenna jack.

3. Place the antenna selection switch in the “B” position.

TYPE 4: Fully automatic radio antenna (B Position)

1. Disconnect the radio antenna lead going to the radio and connect to the transmitter jack

marked “ANT.”

2. Connect the provided male-to-male 18” radio antenna adapter cord between the transmitter

jack marked “RADIO” and the radio antenna jack.

3. Cut the power antenna lead running from the radio to the fully automatic radio antenna.

4. Connect the lead coming from the power antenna to the long white wire (marked “To power

antenna sensor wire”).

5. Connect the lead coming from the radio to the short white wire (marked “To radio switched

power lead”).

6. Place the antenna selection switch in the “B” position.

ENFORCER E-37EV Alarm Pager System

SECO-LARM U.S.A., Inc. 5 SECO-LARM U.S.A., Inc. 33 5

Connection Diagram

Programming

The receiver must learn the transmitter’s code before it can receive signals from the transmitter.

The receiver can learn the page codes of up to 3 transmitters.

1. Turn the receiver OFF. Then press and hold the ON//OFF switch and slide it to the ON

position. Continue holding for 3 seconds until the receiver beeps once.

2. The PAGE LED will flash GREEN at a steady rate. The ZONE LED will be solid ORANGE.

This means the receiver is ready to learn the page code of the first transmitter.

3. Press the manual page button on the transmitter. This will send the page signal to the

receiver. The receiver will beep twice and the LEDs will turn off to indicate the code has been

learned. The receiver will beep five times in four minutes if no code is learned.

4. To learn a second (or third) transmitter, repeat step 1 then press down on the ON//OFF

switch once. The PAGE LED will begin flashing RED for the second transmitter and

ORANGE for the third transmitter.

5. Press the manual page button on the second (or third) transmitter. The receiver will beep

twice and the LEDs will turn off to indicate the page code has been learned. The receiver will

beep five times in four minutes if no code is learned.

6. If no additional transmitters need to be learned then move the ON/ /OFF switch back to

the OFF position.

Notes:

The receiver remembers the transmitter codes in EEPROM memory even without

power for over one year. The receiver does not need to re-learn the transmitter codes

after battery replacement.

Only one of each transmitter ID may be learned at a time. For example, if a green

transmitter is already programmed and a new green transmitter is learned, the previous

green transmitter will no longer work.

E-37ANT

(Optional)

Green: First Negative (-) Trigger

Blue: Second Negative (-) Trigger

Purple: Positive (+) Trigger

Black: Ground

Red: Constant +12V to Fuse

Box

White (Long): Power Antenna

White (Short): Radio Switched Power

Lead

Radio (“RADIO”)

Antenna (“ANT”)

Radio

+12 VDC

Ground

Fuse (2A)

Antenna

LED

Manual Page

Antenna Selection

Switch

Cut

Diode

IN4004

ENFORCER E-37EV Alarm Pager System

6SECO-LARM U.S.A., Inc.

Transmitter

Input

Receiver Display

Page LED

Zone LED

Audible / Vibrator

Indicator

Green

Positive Trigger

Green

Groups of 9

Negative Trigger #1

Green

Red

Groups of 9

Negative Trigger #2

Green

Orange

Groups of 9

Manual Page

Green

3 groups of 3

Power ON

Green

None

3 groups of 3

Red

Positive Trigger

Red

Green

Groups of 9

Negative Trigger #1

Red

Groups of 9

Negative Trigger #2

Red

Orange

Groups of 9

Manual Page

Red

Green

3 groups of 3

Power ON

Red

None

3 groups of 3

Orange

Positive Trigger

Orange

Green

Groups of 9

Negative Trigger #1

Orange

Red

Groups of 9

Negative Trigger #2

Orange

Groups of 9

Manual Page

Orange

Green

3 groups of 3

Power ON

Orange

None

3 groups of 3

Audible and Visual Signals Chart

Operation

Receiver Switch Settings

: Beeping only ON: Vibration only OFF: Receiver off

Trigger Duration

The transmitter will transmit the page signal for a cycle of about 30 seconds, whether or not

the triggered zone is reset. If the same zone remains triggered, the transmitter will not start

a new transmission cycle. However, a new cycle will begin once another un-triggered zone

is triggered.

Manual Paging

When triggered by the manual page button the receiver will beep (or vibrate) continuously

for 1 minute in 3 groups of 3.

The Page LED will indicate which transmitter is sending the signal (Green, Red, or Orange).

The Zone LED will flash green.

Press the ON//OFF button after 30 seconds to stop the indicator.

Power-On Paging

When the transmitter is connected to power the receiver will beep (or vibrate) continuously

for 1 minute in 3 groups of 3.

The Page LED will indicate which transmitter is sending the signal (Green, Red, or Orange).

The Zone LED will remain blank.

Press the ON//OFF button after 30 seconds to stop the indicator.

ENFORCER E-37EV Alarm Pager System

SECO-LARM U.S.A., Inc. 7 SECO-LARM U.S.A., Inc. 33 7

Warning

Ensure that an antenna is connected before connecting power to the unit. Failure to do so may

damage the transmitter.

Do not open the receiver or transmitter cases. All adjustments have been made at the factory.

There are no user serviceable parts inside.

Holes marked 1, 2, and 3 on the transmitter case are factory set. Do not make any

adjustments in these holes.

Use only AAA size 1.5V alkaline batteries for the receiver.

Alarm Paging

When triggered by either the purple (+), green (-), or blue (-) triggers, the receiver will beep

(or vibrate) continuously for 1 minute in groups of 9.

The Page LED will indicate which transmitter is sending the signal (Green, Red, or Orange).

The Zone LED will indicate which trigger was triggered.

-Positive trigger (purple wire) will flash green.

-Negative trigger #1 (green wire) will flash red.

-Negative trigger #2 (blue wire) will flash orange.

Press the ON//OFF button after 30 seconds to stop the indicator.

Receiver Power-On

The receiver will beep (or vibrate) once each time the receiver is turned on.

Unattended Indicator

The receiver will beep (or vibrate) once every 30 seconds to remind the user that it received

a page signal from the transmitter.

Press the ON//OFF button to stop the indicator.

Low-Battery Indicator

The receiver will beep (or vibrate) twice following power-on if the batteries are low.

The receiver will also beep (or vibrate) twice every 60 seconds when the batteries are low.

Viewing the Page Memory

Scroll back the page signal memory by pressing the ON//OFF button repeatedly.

The receiver remembers the last 6 page signals received.

Page signals will be shown one by one, beginning with the most recent.

The receiver will beep once for an alarm page, but will not beep for a manual page.

The receiver will beep three times to indicate that all signals have been viewed, or that no

signals are stored.

Two consecutive page signals carrying the same information are treated as one.

Turning off the receiver will erase all stored signals.

ENFORCER E-37EV Alarm Pager System

8SECO-LARM U.S.A., Inc.

MiE-37EV_1209.docx

PIHKK2

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal

service for a period of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the

repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair

or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such

equipment is not operating properly as a result of causes other than defects in material and workmanship.

The sole obligation of SECO-LARM and the purchaser’s exclusive remedy shall be limited to replacement or repair only, at

SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal

or property damages of any kind to the purchaser or anyone else.

NOTICE

The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM

policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change

specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

in part, without the written permission of SECO-LARM.

SECO-LARM U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Tel: 800-662-0800 / 949-261-2999

Website: www.seco-larm.com

E-mail: sales@seco-larm.com

Also Available from SECO-LARM

E-37RV Vibrating Transmitter

E-37ANT Strip Antenna

FCC COMPLIANCE STATEMENT

Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his or her own expense.

Troubleshooting

No page signal

Check that all connections are securely made

Check that the antenna is securely fastened

Check the receiver batteries

Possibly out of range –Move antenna to better position

Make sure the antenna selection switch is in the correct

position

Check that the transmitter has been properly learned

Receiver only outputting vibrate/beep

Check that the receiver is in the correct alert mode

Table of contents

Other SECO-LARM Security System manuals

SECO-LARM

SECO-LARM Enforcer SM-407-5T User manual

SECO-LARM

SECO-LARM ENFORCER SD-7201GC-PEQ User manual

SECO-LARM

SECO-LARM Enforcer Voice Dialer E-920A User manual

SECO-LARM

SECO-LARM Enforcer SD-7103GC-PEQ User manual

SECO-LARM

SECO-LARM SLI 820R User manual

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TSQ User manual

SECO-LARM

SECO-LARM Enforcer E-921CPQ User manual

SECO-LARM

SECO-LARM ENFORCER SH-816S-SQ Series User manual

SECO-LARM

SECO-LARM Enforcer SS-075CQ User manual

SECO-LARM

SECO-LARM SD-7104SGEX1Q User manual

SECO-LARM

SECO-LARM ENFORCER E-931CS22RFCQ User manual

SECO-LARM

SECO-LARM ENFORCER SH-532BQ User manual

SECO-LARM

SECO-LARM ENFORCER SH-816S-SMQ Series User manual

SECO-LARM

SECO-LARM SD-7175SGEX1Q User manual

SECO-LARM

SECO-LARM ENFORCER K4E931CS22RF User manual

SECO-LARM

SECO-LARM SLI ENFORCER RM-R100-TBQ User manual

SECO-LARM

SECO-LARM Enforcer SH-816S-SQ Series User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual