Sealey AP2030BB User manual

HEAVY-DUTY WORKBENCH WITH 5

DRAWERS BALL BEARING RUNNERS

MODEL NO: AP2030BB

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

1.1 GENERAL SAFETY

WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this bench.

9Locate bench in a suitable working area.

9Keep the work area clean, uncluttered and ensure there is adequate lighting.

WARNING! Use bench on level and solid ground, preferably concrete. Avoid tarmacadam since the bench may sink into the surface.

9Keep the bench clean and tidy in accordance with good workshop practice.

9Keep children and unauthorised persons away from the working area.

8DO NOT use the bench for any purpose other than that for which it is designed.

8DO NOT exceed maximum capacity of workbench.

8DO NOT undertake work on the bench without the work-piece being adequately secured. Use clamps or a vice (not included) to secure

the work-piece. Available from your Sealey dealer.

8DO NOT use the bench out of doors.

8DO NOT get the bench wet or use in damp or wet locations or areas where there is condensation.

8DO NOT clean the bench with any solvents which may damage the paint surface or the protective coating on the wooden top.

2. INTRODUCTION

Powder coated steel panels with 40mm wood laminate top. Five drawers. Open shelving for storage of larger items. Supplied flat packed.

3. SPECIFICATION

Table Size (W x D): ...........................................1372 x 508mm

Working Height: ............................................................865mm

Capacity: ........................................................................250kg

3.1. Carefully unpack the product and check the contents against the diagram below. Should any items be missing or damaged make

immediate contact with your Sealey dealer.

A.....SIDE PANEL H ....RIGHT SIDE PANEL M.....DRAWER R . . . . .RIGHT SlDE RUNNER

C.....BOTTOM RAIL I ..... SUPPORT PANEL O .....CORNER BRACE S..... SCREW SELF TAPPING SCREW

D.....TOP RAIL J..... BACK PANEL P .....WOODEN TOP T..... ADJUSTABLE LEG LEVELLER

E.....CENTRE SUPPORT K .... SHELF Q. ....LEFT SIDE RUNNER U . . . . .HEX HEAD SCREW 5/8”

G.....LEFT SIDE PANEL

g.1

AP2030BB Issue 2 (HF) 26/06/18

Original Language Version

Refer to

instructions

4. ASSEMBLY

4.1. As shown in the diagram assemble the two

large side panels (A), bottom rail (C) and

centre support (E).

4.2. Attach the outer slide to the corresponding left/right side panel (G, H). Insert the tabs into the holes in the side panel making sure that

the slider stop fits into the small hole.

4.3. Attach the side panels (G ,H) onto the main unit by screwing them to the front centre support (E) and side panels. Attach support

panels (I) to the side of the unit without sliders.

g.2

g.3

AP2030BB Issue 2 (HF) 26/06/18

Original Language Version

4.4. Screw the top rails (D) onto the front and back.

4.5. Secure the back panels (J) using 8 screws, 4 in each corner.

4.6.

4.7. Turn the workbench upside down and screw in the corner braces (O) as shown in the diagram. At each corner attach the leg levellers (T). Slide the

workbench top (P) under the main unit and fix with 4 hex head screws (U)

4.8. Attach the inner slides onto the drawers. Slot the horizontal tab into the hole in the drawer and the vertical tab into the other hole. Push down until the

g.4

g.5 g.6

AP2030BB Issue 2 (HF) 26/06/18

Original Language Version

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to

a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely

unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids

according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior

notice.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

AP2030BB Issue 2 (HF) 26/06/18

Original Language Version

stop slots into the small hole.

4.9. Pull the middle slide and the ball bearings out as far as possible. Hold the drawer and slot the inner slide on the drawer into the middle slide, then push