Sealey SC01 User manual

INSTRUCTIONS FOR:

2 DOOR FLOOR CABINET

MODEL No: SC01

1. SAFETY INSTRUCTIONS

2. INTRODUCTION

1.1 GENERAL SAFETY

 WARNING! Ensure Health & Safety, local authority, and general workshop practice

regulations are adhered to when using this cabinet.

 WARNING! Use caution when handling and assembling the metal components.

The metal may have sharp edges or corners, the use of protective gloves is recommended.

Locate cabinet in a suitable working area and secure to a wall with suitable fasteners.

Keep the work area clean, uncluttered and ensure there is adequate lighting.

Keep the cabinet clean and tidy in accordance with good workshop practice.

Keep children and unauthorised persons away from the working area.

DO NOT climb, step or stand on the cabinet shelves.

DO NOT use the cabinet for any purpose other than that for which it is designed.

DO NOT use in damp work areas.

 WARNING! The warnings, cautions and instructions referred to in this instruction manual

cannot cover all possible conditions and situations that may occur. It must be understood

that common sense and caution are factors which cannot be built into this product, but must

be applied by the operator.

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,

WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.

FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE

KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

SC01 Issue No: 1 - 28/08/08

Featuring two large doors, four shelves and base storage. Added security provided by cylinder

lock and supplied with two keys. All steel construction, stabilized by an inner cross member.

Overall Size (W x D x H): 915 x 457 x 1981mm

Fig.1

3. ASSEMBLY

3.1 CONTENTS INSPECTION

Unpack all the parts and layout on the packing

material. Visually inspect all panels to check for

transportation damage.

CONTENTS

A BACK PANEL (RIGHT)

B BACK PANEL (LEFT)

C SIDE PANEL (RIGHT)

D SIDE PANEL (LEFT)

E CROSS MEMBER (INNER)

F CROSS MEMBER (OUTER)

G BOTTOM PANEL

H TOP PANEL

I DOOR PANEL WITH LOCK (RIGHT)

J DOOR PANEL (LEFT)

K SHELF

L PLASTIC INSERT

M HINGE INSERT

N RUBBER BUMPER

O SCREW (M6 X 15)

P WASHER

Q SHELF CLIP

R KEY

SC01 Issue No: 1 - 28/08/08

Fig.2

Fig.4

Fig.3

Fig.5

3.4 INNER CROSS MEMBER ASSEMBLY (Fig.4)

3.4.1 Insert the cross member (E) as shown in Fig.4 and secure using screws (O) and washers (P).

3.5 BASE ASSEMBLY (Fig.5)

3.5.1 Slidethebase(G)intopositionandlocateontothetabsonthebackandsidepanels.Thefrontedgetsovertheinnercross

member.

Fig.6 Fig.7

3.2 BACK ASSEMBLY (Fig.2)

3.2.1 Placethebackpanels(A&B)onasuitablyprotectedatsurfacetopreventscratching.

3.2.2 Interlock the tabs into the slots on the back panels and slide together until the two panels are fully engaged.

3.3 SIDE ASSEMBLY (Fig.3)

3.3.1 Holdthesidepanels(C&D)ataslightangleandtthetabsonthebackpanelsintotheslotsofthesidepanelsandslide

down to engage.

3.6 OUTER CROSS MEMBER ASSEMBLY (Fig.6)

3.6.1 Fit the outer cross member (F) and secure with the two plastic oval inserts (L) and two hinge inserts (M).

3.7 TOP ASSEMBLY (Fig.7)

3.7.1 Fitthetop(H)tothecabinetandpushdownuntilthetabslockintoposition,ttwoplasticovalinserts(L)andtwohinge

inserts (M) as shown in Fig.7. With the aid of another person carefully lift the cabinet from the top into an upright position.

01284 757500

01284 703534

sales@sealey.co.uk

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

SC01 Issue No: 1 - 28/08/08

Fig.9

Fig.8

3.9 SHELF ASSEMBLY (Fig.9)

3.9.1 Insert shelf clips (Q) at the desired height for each shelf and lay the shelves onto the clips.

3.10 Use a mild solution of detergent and water and wipe the unit down with a soft cloth.

3.8 DOORS ASSEMBLY (Fig.8)

3.8.1 Locate the bottom door pin into the lower bush and pull down the spring loaded top pin and align with the bush in the top

panel, release the pin to locate. Repeat with the other door.

3.8.2 Fit the rubber bumpers (N) as shown in Fig.8 to the left hand door.

Parts support is available for this product.

To obtain a parts list and diagram please log on to www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500

Table of contents

Popular Tools Storage manuals by other brands

Ryobi

Ryobi RWB03 Original instructions

Husky

Husky H27CH5TR4BGK Use and care guide

Scheppach

Scheppach ts 2100 Translation from original manual

Cornwell Tools

Cornwell Tools CTB360AKBK Assembly instructions

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SHAIN GSB-6024 Assembly instruction

Cassese

Cassese CS200 CART user & parts manual

Kendall Howard

Kendall Howard ESDW-9630-1000 owner's manual

Lista

Lista Align Instructions for assembly

Workzone

Workzone 99609 Assembly instructions

Stanley

Stanley STST83800-1 instruction manual

Homak

Homak PROFESSIONAL Series Owner's manual & operating instructions

Perel

Perel ROLLER SHUTTER STORAGE CABINET Assembly instructions

Husky

Husky H5CH2R Use and care guide

BGS technic

BGS technic 4107 manual

Clarke

Clarke CWB1250 Instruction

Ryobi

Ryobi RWB02 Original instructions

Husky

Husky H52CH6HDV3WHT Use and care guide

General International

General International Excalibur 40-100 Setup & operation manual