Seagull Models Husky User manual
“Graphics and specifications may change without notice”.
MS:180
ASSEMBLY MANUAL
Specifications:
Wingspan------------------------------79.9in(203cm).
Wing area -----------------922.3sq.in (59.5sq dm).
Weight ------------------------7.9-8.8lbs (3.6-4.0kg).
Length ------------------------------50.0in (127.0cm).
Engine ------------------0.61-0.75cu.in-----2-stroke.
0.91.in -----4-stroke.
Radio ------------------- 5 channels with 7 servos.
Electric conversion: optional
CHRISTEN HUSKY Instruction Manual.
2
INTRODUCTION.
Thank you for choosing the CHRISTEN HUSKY ARTF by SEAGULL MODELS COMPANY LTD.
The CHRISTEN HUSKY was designed with the intermediate/advanced sport flyer in mind. It is a
semi scale airplane which is easy to fly and quick to assemble. The airframe is conventionally built
using balsa, plywood to make it stronger than the average ARTF , yet the design allows the aeroplane
to be kept light. You will find that most of the work has been done for you already.The motor mount
has been fitted and the hinges are pre-installed . Flying the CHRISTEN HUSKY is simply a joy.
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your CHRISTEN HUSKY . Use the parts listing
below to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C supplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
procedures designed to help the new pilot on his way to successful R/C flight. They will also be able
to advise on any insurance and safety regulations that may apply.
KIT CONTENTS
1
3
2
2
4
11
5
3
6
10
3
www.seagullmodels.com
ADDITIONAL ITEMS REQUIRED.
0.61- 0.75 2-stroke.
0.91 4-stroke.
Computer radio with 7 servos.
Glow plug to suit engine.
Propeller to suit engine.
Protective foam rubber for radio
system.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modelling knife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
SEA180 CHRISTEN HUSKY 2030mm
SEA18001 Fuselage
SEA18002 Wing set
SEA18003 Tail set
SEA18004 Cowling :
SEA18005 Main Landing Gear
SEA18006 Tail Gear
SEA18007 Windshield Set
SEA18008 Decal Set
SEA18009 Linkage Set
SEA18010 Wing Tube
SEA18011 Fiberglass Wheel pants
ZZBSEA180B Replacement Box
FL180 Floating set for Christen Husky
KIT CONTENTS.TS HINGING THE FLAP
M2x10mm.
M2x10mm.
CHRISTEN HUSKY Instruction Manual.
4
??
HINGING THE ELEVATORS
1)Locate the items for this section of the
manual.
2)Carefully remove the elevator from one of
the horizontal stabilizer panels. Note the
position of the hinges. Used C/A glue to fix the
hinges position..
3) Remove each hinge from the horizontal
stabilizer panel and elevator and place a T-
pin in the center of each hunge. Slide each
hinge into the elevator until the T-pin is snug
against the elevator. This will help ensure an
equal amount of hinge is on either side of the
hinge line when the elevator is mounted to
the horizontal stabilizer panel.
Epoxy
Epoxy
C/A glue
C/A glue
5
www.seagullmodels.com
INSTALL THE AILERONS CONTROL
HORN.
Epoxy
Fiberglass control horn.
INSTALL THE .
Epoxy
Epoxy
Fiberglass
Glue the rudder hinges in place using the
same techniques used to hinge the ailerons.
HINGING THE RUDDER
CHRISTEN HUSKY Instruction Manual.
6
INSTALL ELEVATOR CONTROL
HORN.
INSTALL RUDDER CONTROL HORN.
Repeat steps to install the rudder control horn
as same as steps done for ailerons.
Fiberglass control horn.
Fiberglass control horn.
Epoxy
Epoxy
Flap control horn.
Aileron control horn.
Epoxy
Install the flap control horn using the same
method as same as the aileron control horns.
INSTALL FLAP CONTROL HORN.
Fiberglass control horn.
7
www.seagullmodels.com
WHEEL AND WHEEL PANTS.
1)Assembling and muonting the wheel pants
as shown below pictures.
Wheel collar.
Axle
Epoxy.
Rudder control horn.
Epoxy
wheel collar.
wheel.
Axle.
Washer.
M3.
wheel Pant.
wheel.
M3.
M3.
wheel collar.
nut. Axle.
Washer.
M3.
C/A glue.
INSTALLING THE MAIN LANDING
GEAR TO FUSELAGE.
M4x20mm
CHRISTEN HUSKY Instruction Manual.
8
M4x20mm
M4x20mm
M4x20mm
INSTALLING WHEEL PANTS TO
MAIN LADING GEAR.
ENGINE MOUNT INSTALLATION.
1) Locate the items necessary to install the
engine mount included with your model. .
4x30mm.
Thread locker glue.
2) Use four 4x30mm head bolts and four 4mm
washers to attach the engine mount rails to
the firewall. Tighten the screws . Make sure to
use threadlock on the screws to help prevent
them from vibrating loose.
Thread locker glue
C/A glue.
Landing Gear. wheel Pant.
Locker glue.
9
www.seagullmodels.com
3) Carefully bend the second nylon tube
up at a 45º angle. This tube is the vent tube.
4) Test fit the stopper assembly into the
tank. It may be necessary to remove some of
the flashing around the tank opening using a
modeling knife. If flashing is present, make
sure none falls into the tank.
Vent tube. Fuel pick up tube.
Fuel fill tube.
INSTALLING THE STOPPER ASSEMBLY.
2) Using a modeling knife, cut one length
of silicon fuel line. Connect one end of the line
to the weighted fuel pick up and the other end
to the nylon pick up tube.
1) Using a modeling knife, carefully cut
off the rear portion of one of the 3 nylon tubes
leaving 1/2” protruding from the rear of the
stopper. This will be the fuel pick up tube.
C
A
B
5) With the stopper assembly in place,
the weighted pick-up should rest away from
the rear of the tank and move freely inside the
tank. The top of the vent tube should rest just
below the top of the tank. It should not touch
the top of the tank.
6) When satisfied with the alignment of
the stopper assembly tighten the 3 x 20mm
machine screw until the rubber stopper ex-
pands and seals the tank opening. Do not
overtighten the assembly as this could cause
the tank to split.
FUEL TANK INSTALLATION.
You should mark which tube is the vent
and which is the fuel pickup when you
attach fuel tubing to the tubes in the
stopper. Once the tank is installed inside the
fuselage, it may be difficult to determine which
is which.
CHRISTEN HUSKY Instruction Manual.
10
Fuel tank.
7) Slide the fuel tank into the fuselage. Guide
the lines from the tank through the hole in the
firewall.
8) Use plywood template to hold in place
the fuel tank with C/A glue to secure the fuel
tank inside the fuselage.
C/A glue.
9) Connect the lines from the tank to the engine
and muffler. The vent line will connect to the
muffler and the line from the clunk to the
carburetor.
Vent tube.
Fuel pick up tube.
Fuel fill tube.
A
C/A glue.
C
B
Blow through one of the lines to en-
sure the fuel lines have not become kinked
inside the fuel tank compartment. Air
should flow through easily.
INSTALLING THE FUSELAGE SERVOS.
1) Install the rubber grommets and brass
collets onto the throttle servo. Test fit the servo
into the aileron servo mount.
2) Secure the servos with the screws pro-
vided with your radio system.
Because the size of servos differ, you
may need to adjust the size of the precut open-
ing in the mount. The notch in the sides of the
mount allow the servo lead to pass through.
Table of contents
Other Seagull Models Toy manuals
Seagull Models
Seagull Models ERCOUPE User manual
Seagull Models
Seagull Models SEA158 User manual
Seagull Models
Seagull Models EDGE 540 EP User manual
Seagull Models
Seagull Models Low Wing Sport V2 10cc ARF User manual
Seagull Models
Seagull Models AT-6 TEXAN User manual
Seagull Models
Seagull Models SEA 94 Pilatus PC-9 User manual
Seagull Models
Seagull Models TWIN COMANCHE SEA134 User manual
Seagull Models
Seagull Models steen skybolt n250sb User manual
Seagull Models
Seagull Models Embraer EMB-312 Tucano T-27 Brazilian Air Force 85 span... User manual
Seagull Models
Seagull Models 15CC User manual
Seagull Models
Seagull Models SWIFT40 User manual
Seagull Models
Seagull Models KA8-B User manual
Seagull Models
Seagull Models De Havilland DH-60M Moth 72" wingspan... User manual
Seagull Models
Seagull Models T-34 Mentor User manual
Seagull Models
Seagull Models ANGEL GLIDER 2000 User manual
Seagull Models
Seagull Models SEA238 User manual
Seagull Models
Seagull Models Super Tucano T-27 User manual
Seagull Models
Seagull Models Mini Sparrowhawk EP User manual
Seagull Models
Seagull Models SEA 285 User manual
Seagull Models
Seagull Models SEA EAGLE User manual
