Schlage 7766 User manual
*77660*
77660
1 Prepare frame for switch.
1a Prepare frame for surface installation of 7766 Switch.
LNote: For maximum security, it is recommended that the switch be installed in the header, 2” from the lock stile edge.
1b Wire & install switch.
2 Prepare door for magnet.
2a Install magnet.
Check List
Magnet
Arrow on Magnet Label
Must Point Toward Switch
Arrow on Switch Label Must
Point Toward Door
Switch
Wiring Diagram
Yellow
Blue
Red
SWITCH SHOWN
MAGNETICALLY ACTUATED
Lock Stile
Edge Mounting
RHR
Shown
2” Backset
Recommended
6” Maximum Backset
Overhead Mounting
(See note in Step 1-A
of installation Instructions)
If switch does not work:
check recommended gap and
decrease if necessary.
Lock Stile
Edge of Door
2 13/32”
For RHR Door
1”
1/2”
1/8”
Recommended
Gap
7/32”
3”
2”
1/2”
1/2”
Frame
19/32”
For LHR Door
Lock Stile
Edge of Door
#6 X 3/4” Sheet Metal
Screws - 4 Places 9/32” Dia. Through Frame for
Wiring Access on Switch
1”
WARNING:
THESE ARE SIGNAL SWITCHES. NOT
INTENDED FOR DIRECT SWITCHING.
Type
.25 AMP
7766
Current
Rating
Surface Mount
7766 Magnetic Door
Position Switch
Installation Instructions
© Allegion 2014
Printed in U.S.A.
77660 Rev. 01/14-d
Typical Signalling Application
Red
Magnetic Switch*
Magnetic Switch*
* Switch Shown with Door Shut
LED Panel
LED Panel
Power Supply
LED
Maximum
Voltage
is 24 Volts
LED Panel Notes:
Console
Monitor Input
(Open Loop)
Yellow
Blue
Red
Yellow
Blue
LED will light when door
is open. If a lamp is
used instead of an LED,
limit current to .04 AMP.
Typical Load Switching Application
Magnetic Switch*
Switch Shown
with Relay Energized Relay Notes:
24VDC Relay
24VDC
Fail Safe
Lock
1N4004
Diode
24VDC
Power
Supply
Lock Control
Switch
Red
Yellow
Blue
24 VAC
Fail Safe
Lock
24 VAC Relay
Relay Notes:
Voltage
Suppressor
Magnetic Switch*
24VAC
Transformer
Lock Control
Switch
Switch shown
with Relay Energized
Red
Yellow
Blue
Select a relay with a coil voltage rating
of 24VDC. Coil current is not to exceed
.2 AMP. The contact rating is dependent
on the load current requirements. An
IN4004 or equivalent diode is used to
prevent inductive EMF from damaging
the magnetic switch contacts.
Select a relay with a voltage rating of 24VAC. Coil current
is not to exceed .2 AMP. The contact rating is dependent
on the load current requirements. Voltage suppressor can
be a P6KE36C Transzorb (general semiconductor) or a
V39ZA1 MOV (general electric), which is used to prevent
inductive EMF from damaging the magnetic switch
contacts.
* Switch Shown with
Door Shut
Customer
Service
1-877-671-7011
www.allegion.com/us
Table of contents
Other Schlage Door Lock manuals
Schlage
Schlage B-Series User manual
Schlage
Schlage B360/F User manual
Schlage
Schlage CO-220-75 User manual
Schlage
Schlage Encode User manual
Schlage
Schlage LE162 Wiring diagram
Schlage
Schlage FC60 User manual
Schlage
Schlage BE365 User manual
Schlage
Schlage CO-250 User manual
Schlage
Schlage DCT-A00XP14-00 User manual
Schlage
Schlage Encode SMART WIFI LEVER User manual
Schlage
Schlage D170 User manual
Schlage
Schlage AD-250 User manual
Schlage
Schlage BE365 User manual
Schlage
Schlage LE User manual
Schlage
Schlage BE468 series User manual
Schlage
Schlage L9000 Series User manual
Schlage
Schlage AD-200 User manual
Schlage
Schlage BR260 User manual
Schlage
Schlage PC60 User manual
Schlage
Schlage V10 User manual
