Saveo Scan SAVEO-RV2-Z12D User manual
* shown with Motorola MOTO G 6th Generation
Scanning with Simplicity
www.saveoscan.com
US PH: +1 720 257 7070
UK PH: +44 208 0998071
info@saveoscan.com
SAVEO-RV2-Z12D
Bluetooth SPP set-up guide
1. Getting Started
Introduction
Product Inforrmation
Operating Elements
LED Indicator
Attaching your phone to the scanner
Connecting via Bluetooth SPP
Unpairing your device
2. User Preferences
Operating Modes
Reset to Defaults
Battery Level Status
Power Saving Mode
Sound Settings
Reading Mode
Mobile Phone/Display Mode
Transmission Speed
3. Troubleshooting
4. General Information
5. Further Information
03
04
05
07
08
11
16
17
20
21
22
23
24
25
26
27
28
29
Contents
This document provide an easy way to program the decoding options and interface
selections by scanning barcodes listed in this guide.
Introduction
3
Important Notice
When printing barcodes for programming, the use of a high-resolution laser printer is
strongly recommended for the best scan result.
The settings will be updated periodically without prior notice. For the latest version, please
contact your authorized distributor.
Settings and Programming
Scan a series of selected barcode patches in this manual to affect setup and
programming of your handheld 1D Image Reader. Decoding options and interface
protocols can be tailored to a specific application.
Setup parameters are stored in non-volatile memory in the scanner and are retained even
when power is o. Setup parameters change only when you reset them.
You may need to hide adjacent code patches with your hand when doing programming
scanning.
Getting started
Table of Contents
Limited Warranty
Saveo Scan provides a one year limited warranty.
This warranty does not cover any product which has been subject to improper use,
neglect or unauthorized repair or installation.
This warranty does not cover consumable parts. (Cables & batteries are consumables.)
* Don’t put scanner in places of excessively high temperature, such as exposure to
direct sunlight
* Don’t use scanner in extremely humid conditions or in conditions of extreme
temperature change
* The rechargeable battery is permanently built into the product and cannot be
replaced.
* Never damage the rechargeable battery. Damaging the casing of the rechargeable
battery might cause explosion or re!
Product Information
Delivery contents
1 x SAVEO-RV2-Z12D scanner
1 x Charging Cradle
1 x Micro USB cable
4
Safety instructions
Read the operating instructions carefully and pay special attention to the safety
information. If you do not follow the safety instructions and information on proper
handling in this manual, we assume no liability for any resulting personal injury or
damage to property.
Table of Contents
Getting started
Getting Started
Power Switch
Power switch is located on the
underside of the scanner.
5
Switch on and Charge your Scanner
Please switch on your scanner (as illustrated) and place it in the cradle to charge for 3~4
hours before rst use.
If you want to charge smartphone and scanner simultaneously, please switch scanner to
C (Charge Mode) before placing it in the cradle.
Power on Saveo Scan
On the underside of the scanner you will nd a small recessed button.
Use a pen or paper clip to push the button until you hear a notication sound.
Ensure power switch remains depressed after you release it.
Operating Elements
Table of Contents
Operating Elements
Wrist Strap
Universal Holder
Exit Window
Getting Started
6
Table of Contents
Scan/Wake Button
(For iOS devices ONLY. Press and
hold for four seconds to raise and
lower the on-screen keyboard)
LED indicator
For Optimal Charging, please use the
original USB cable & adaptor supplied with
your mobile device. Micro USB or USB Type-C
Switch for O (Operation Mode)
and C (Charge Mode)
Use Micro USB, Type-C, or
Lightning cable (Optional) to
connect to smartphone/tablet
* shown with Optional
SBB005 Custom Rugged
Case Mount and SCF001
Saveo Flex-Protect™ Ultra-
Thin Cable
Select the Charge & Data model for the device type
by scanning the barcode below:
Type-C
Micro USB
LED Indicator
Please refer to the table below for information regarding LED status indicator.
Orange LED ON Full charged
Orange LED (Flashing) Charging / Low battery
Red LED ON Oine / Out of Range
Green LED ON Good read
Orange LED ON Good read (Batch mode)
LED Indicator Information
Getting Started
7
Table of Contents
Please Note: When the battery power is too low, the Orange LED will ash and the scanner
will emit a ‘beep’ at regular intervals. The scanner should be charged immediately. If
scanner shuts down it is recommended to charge it fully then power it back on.
Please Note: When the scanner is in sleep mode there will be no LED indication when
charging.
Attaching your phone to the scanner
Attaching your smartphone to scanner using the universal holder
Extend the retractable arm before placing phone in holder and then pushing it rmly
back against the phone.
You can view a video deomonstration here: http://youtu.be/-x-n6RMleUY
Extend retractable arm
Press button and slide outwards to
extend the arm
Insert phone
Secure phone in holder
Retract the arm until phone is held rmly
in place
Getting Started
8
Table of Contents
Attaching your phone to scanner using the smartphone ruggediser
The ruggedised case can be attached directly to the top of the scanner. The case has two
components, an inner silicone cover and an outer layer of hardened polycarbonate,
oering excellent protection while also allowing the phone to be removed with ease.
You can view a video deomonstration here: http://youtu.be/-x-n6RMleUY
The hardened polycarbonate shell is
attached securely to the scanner with
three M2X12 phillips head screws.
The phone and silicone cover are
inserted into the outer shell.
Attaching your phone to the scanner
Getting Started
9
Table of Contents
Attaching your phone to the scanner
Getting Started
10
Table of Contents
Connect phone to scanner with Micro-USB cable
As USB connection locations vary on dierent models of smartphone, the cable can be
congured for your specic model.
Please Note: The Micro-USB connection supports charging on all connected devices
and data transfer on USB OTG capable devices only.
For iOS devices, please use appropriate micro-USB adapter.
Other manuals for SAVEO-RV2-Z12D
1
Table of contents
Other Saveo Scan Scanner manuals
