SATO SG112-ex User manual
BARCODE PRINTER
SG112ex +RTC
(KITTING MANUAL)
30/SEP/2019
Technical Department SPZ
PE-E30A02
Required tools:
•Phillips screwdriver (JIS #2, or equivalent)
To Install the Optional Real-time Clock Kit
1
Power off the product and disconnect the AC power cord.
2
Remove three screws 1 on the top of
front panel and left cover.
3
Remove two screws 2 on the back of
left cover.
4
With the media tray 3 pulled out, slide
the cutter cover 4 upwards to remove
it.
5
Release the hook at the lower part of
front panel, slide the front panel tothe
right and remove the screw 5 securing
the left cover.
6
Remove the left cover carefully so that
the KB cables are not disconnected.
7
Removetwo
screws
6andthenremove
the
RTC bracket
7.
8
Install the
RTC PCB
(
to the
RTC
bracket
8bytighteningtwo
screws
9
(Torque: 7-8kgf-cm).
9
Install the
RTC bracket
8
back to the
product by tightening two
screws
6
(Torque:7-8kgf-cm),andwindthe
RTC
cables
"
one round as shown.
10
Connectthe
RTCcables
"
tothe
CN6
RTCconnector
onthe
main
(CONT)
PCB
.
11
Install the left cover and tighten the
screw 5 at the lower part in front.
1
0
1
0
CN6 RTC
12
Tighten two screws 2 at the back of the
left cover.
13
Tighten one screw 1 at the top of the
left cover.
14
Make sure that the KB cables are
connected to the operator panelKB
PCB.
15
Install the front panel and tighten two
screws 1 on the top.
16
Install the cutter cover 3 and push back
the media tray 4.
6.1.2 To set the calendar (date and time)
1 Press the power switch of the product to
the “I” (on) position.
2 When the product is in online mode,
press the LINE button to change the
product to offline mode.
3 Press the ENTER button.
The product changes to setting mode menu.
4 Select the ADVANCED MODE using the
/ / / buttons.
ADVANCED MODE shows on the screen and the
icon is highlighted in reverse.
5 Press the ENTER button to enter the
advanced mode.
Note
If password function is enabled, PASSWORD is shown
on the screen instead. In this case, enter the password
first.
6 Press the ENTER button again until SET
CALENDAR shows on the screen.
7 Press the / buttons to select YES and
press the ENTER button to enter the
calendar setting.
8 Set the Year/Month/Date and the time in 24
hour format using the / / / buttons.
Press the ENTER button to enter the
setting.
9 Input again the same Year/Month/Date/
Time and press the ENTER button to
confirm calendar setting.
10 Press the ENTER button to enable the
calendar check function.
11 Do a factory test printing to make sure that the date and time can be printed on the
label.
Other manuals for SG112-ex
2
Other SATO Barcode Reader manuals
SATO
SATO Argox D4 Series User manual
SATO
SATO ARGOX GPIO User manual
SATO
SATO MB200 User manual
SATO
SATO ARGOX AS-9400BT User manual
SATO
SATO M-8400RVe Series User manual
SATO
SATO Argox P4 Series User manual
SATO
SATO ARGOX AS-9400DC User manual
SATO
SATO MB410i User manual
SATO
SATO MB 200i User manual
SATO
SATO ARGOX AS-9400DC User manual
SATO
SATO ARGOX AS-9400DC User manual
SATO
SATO Argox D4 Series User manual
SATO
SATO CG412DT User manual
SATO
SATO PV3 Instruction manual
SATO
SATO VP208 User manual
SATO
SATO CT408i DT User manual
SATO
SATO CL4NX RIDF User manual
SATO
SATO WS408TT-STD User manual
SATO
SATO PV4 User manual
SATO
SATO GL 4xxe Series User manual
