Salus VS20WRF User manual

1VS20WRF and VS20BRF Installer Manual

4 in 1 Digital Thermostat RF

Models: VS20WRF and VS20BRF

VS10WRF and VS10BRF

INSTALLER / USER MANUAL

2VS20WRF and VS20BRF Installer Manual

Contents

1 x Installer / User manual

4x AAA Batteries

VS20RF

Fixing screws

Contents

Box contents

Introduction

Product Compliance

System options overview

Installation

Parameter Settings

Error Codes

User Guide

Installers notes

Warranty

Box Contents

Icons used in this manual:

Safety

Important info

Your benefit

For latest PDF installation

guide please go to

www.salus-controls.com

VS10RF

3VS20WRF and VS20BRF Installer Manual

Product Compliance & Safety Information

INTRODUCTION

Thank you for purchasing the SALUS 4 in 1 room

thermostat. It must be used with the UG600/

UGE600 or with the CO10RF Zigbee Coordinator.

The Zigbee universal gateway/coordinator

allows communication with other devices in the

Salus SmartHome range. Other Zigbee devices

include wiring centre, system receiver & TRV.

Salus SmartHome Range

Safety Information

Use in accordance with the regulations. The

SALUS VS10RF/VS20RF is to be used for room

control of heating and hot water systems inside

the house.

SALUS Wiring Centre KL08RF

RX10RF

We hope you enjoy this product...

VS20 Thermostat

CO10RF

TRV10RFM

These instructions are applicable to the SALUS

model stated on the front cover of this manual

only.

Warning

This product must be fitted by a competent

person, and installation must comply with

the guidance, standards and regulations

applicable to the city, country or state where

the product is installed. Failure to comply with

the requirements of the relevant guidance,

standards and regulations could lead to injury,

death or prosecution.

UG600/UGE600

4VS20WRF and VS20BRF Installer Manual

Product Compliance & Safety Information

Installer parameter settings

The SALUS VS20 are equipped with installer parameter

section (see page 71) this must only be entered by

the installer or competent person. Changing these

parameters can have a serious effect on your heating

system

For the installer

Please enter any parameter changes in the installer

notes section (pages 111)

230V AC

Sources of danger

The thermostat must be disconnected from main

supply before removing the cover.

Emergency

Switch off the voltage to the individual thermostat

wring centre or complete system.

Warning

Always isolate the AC Main supply before

installing or working on any components that

require 230 VAC 50Hz supply.

This product complies with the essential requirements

and other relevant provisions of Directives 2014/30/

EU, 2014/53/EU (2014/35/EU forVS10WRF/VS10BRF)

and 2011/65/EU. The full text of the EU Declaration

of Conformity is available at the following internet

address: www.saluslegal.com.

Product Compliance

5VS20WRF and VS20BRF Installer Manual

System Overview - Configuration Options

Programmable Room

Thermostat (PRT)

* Grouping and timer option only available

when used with wiring centre.

UFH Manifold

Wiring Centre

Radiator

Boiler

Hot Water

TRV

Towel Rails

Group Control

Thermostat*

Group

Thermostat*

Timer

The unit can be configured to

either one of the following

6VS20WRF and VS20BRF Installer Manual

System Overview - Configuration Options

Programmable Room Thermostat (PRT)

When configured for PRT (see page 30) it mainly works by itself and allows the user to have separate Time

and Temperature control of each zone on the wiring centre, radiator valve or system receiver. Features

like Vacation , Party frost mode have to set on each individual thermostat. All PRTs paired with a wiring

centre can also use the global heat/cool changeover function if the your system supports this. This is

achieved by using the heat/cool changeover connection on the wiring centre (see wiring centre guide).

Group Control Thermostat

When configured for a PRT (see page 30) it can operate as a group control thermostat by assigning a

group when pairing with the wiring centre this allows central control of up to 7 group thermostats see

below, there can be a maximum of 2 groups per 8 zone wiring centre. Permanent temperature override,

Holiday, Party, Frost modes, can be selected centrally from the Group Control Thermostat. Holiday will

also be applied to a timer if applicable. The group thermostats can be also globally changed from heating

to cooling thermostats if you system supports this by using the switched input connection on the WC.

Group Thermostat

When configured as a digital thermostat and assigning a group when pairing with a WC it can operate as

a group thermostat (see page 29), in group mode the group thermostat will follow the time schedule and

any override modes of the group control thermostat. At least one group control thermostat is required for

grouping see above. The group thermostat can have its own programmed temperatures, manual override

and also be removed from the group temporarily or permanently.

Timer

When configured to timer the unit will operate as a timer with no temp control. This can be used for hot

water control. The timer will also follow Holiday mode from the group control thermostat if applicable.

SYSTEM

OVERVIEW

7VS20WRF and VS20BRF Installer Manual

System Overview - Zigbee Coordinator

Zigbee coordinator required for communication between these devices.

RX10RF

CO10RF TRV10RFM

KL08RF

VS20RF

UG600/UGE600

8VS20WRF and VS20BRF Installer Manual

System Overview - Salus SmartHome System

The thermostat can communicate with all these Salus SmartHome

devices.

System Receiver configured to boiler receiver.

Refer to system receiver manual RX10RF.

System Receiver

configured to one

room receiver RX2.

Refer to system

receiver RX10RF.

UNDERFLOOR HEATINGMANIFOLD

Max 6 TRV per thermostat

KL08RF or KL08NSB can be used

SYSTEM

OVERVIEW

9VS20WRF and VS20BRF Installer Manual

System Overview - Hot Water Option

Unit configured to

Hot Water Timer.

When the unit is configured as a hot water timer (see page 32)

there are two methods of connecting the cylinder thermostat.

Cylinder thermostat options

1Connected direct to WC (Default)

2Connected direct to VS20RF (requires additional parameter change. See page 71)

10 VS20WRF and VS20BRF Installer Manual

System Overview - Hot Water Option

1Connected direct to WC (Default)

For convenience there is a unique built in option allowing the cylinder

thermostat to be connected to either the HW Timer or Wiring Centre.

Please refer to Wiring Centre guide and pages 15, 20 for more information.

2Connected direct to VS20RF

(requires additional parameter change see page 32)

SYSTEM

OVERVIEW

Other manuals for VS20WRF

This manual suits for next models

Table of contents

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide